[Why]
On 14us for exit latency time causes underflow for 8K monitor with HDR on.
Increasing the latency to 28us fixes the underflow.
[How]
Increase the latency to 28us. This workaround should be sufficient
before we figure out why SR exit so long.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In current code, we recognize a pipe as a phantom pipe if it references
the same phantom stream. However it can also a phantom split pipe.
If the phantom split pipe has a smaller pipe index than the phantom pipe
we will mistakenly use the phantom split pipe as the phantom pipe. This
causes an incorrect subvp configuration where the first half of the
screen is flashing solid white image.
[how]
Add additional check that the pipe needs to be an OTG master pipe.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous patch to allow DTBCLK disable didn't address boot case. Driver
thinks DTBCLK is disabled by default, so we don't send disable message to
PMFW. DTBCLK is then enabled at idle desktop on boot, burning power.
[How]
Set dtbclk_en to true on boot so that disable message is sent during first
commit.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank
in FPO / SubVP / DRR cases will not have any effect
and we could hit underflow / corruption.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream
so there is no need to have two flags to control it. Unifying
this to a single flag allows dc_stream_adjust_vmin_vmax to skip
actual programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Originally, PMFW said min FCLK is 300Mhz, but min DCFCLK can be increased
to 400Mhz because min FCLK is now 600Mhz so FCLK >= 1.5 * DCFCLK hardware
requirement will still be satisfied. Increasing min DCFCLK addresses
underflow issues (underflow occurs when phantom pipe is turned on for some
Sub-Viewport configs).
[how]
Increasing DCFCLK by raising the min_dcfclk_mhz
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sohaib Nadeem <sohaib.nadeem@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want acknowledgment of the driver idle disallow from DMCUB before
continuing with any further programming.
For idle allow we want to minimize the chance of DMCUB actively
interacing with other firmware components on the system (eg. PMFW)
at the same time.
[How]
Ensure that DMCUB isn't in the middle of processing other command
submissions prior to allowing idle and after disallowing idle by
inserting a wait before the allow and by changing the wait type for
the idle disallow.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d ("drm/amd/display: add null checks before logging")
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Color caps changed between HW versions, which caused the DCN10 color
state sections in the DTN log to no longer match DCN2+ state. Create a
color state log specific to DCN2.0 and hook it up to DCN2 family
drivers. Instead of reading gamut remap reg values, display gamut remap
matrix data in fixed 31.32.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add color caps information for DPP and MPC block to show HW color caps.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Color caps changed between HW versions, which caused the DCN10 color
state sections in the DTN log to no longer match DCN3+ state. Create a
color state log specific to DCN3.0 and hook it up to DCN3.0+ and DCN3.1+
drivers.
rfc-v2:
- detail RAM mode for gamcor and blnd gamma blocks
- add MPC gamut remap matrix log
v3:
- read MPC gamut remap matrix in fixed 31.32 format
- extend to DCN3.0+ and DCN3.1+ drivers (Harry)
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- FW Release 0.0.201.0
- Fix resizing video window for dcn321
- Fix timing bandwidth calculation for HDMI
- Fix null-deref in dml2 assigned pipe search
- Add GART memory support for dmcub
- Add power_state and pme_pending flag
- Add usb4_bw_alloc_support flag
- Revert "Rework DC Z10 restore
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Because ABM will wait VStart to start getting histogram data,
it will cause we can't enter IPS while full screnn video playing.
[How]
Modify the panel refresh rate to the maximun multiple of current
refresh rate.
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It has been found a regression caused by enabling this feature during ODM to
MPC combine switch when user is resizing video window. The transition is
only needed when the feature is enabled. During the transition driver will
temporary switch to use max dppclk level through SMU set hard min interface.
The interface times out and fail to configure the max dpp clock level, which caused
system issue as the desired clock can't be set. We will continue investigating
the issue and root cause the issue where max dppclk level can't be reached.
But for now we have to disable this feature as this feature will cause us to hit this
problem in common use cases during video playback unfortunately. The issue
is dcn321 specific so it won't impact other dcn revisions.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Logging DCN3 MPC state was following DCN1 implementation that doesn't
consider new DCN3 MPC color blocks. Create new elements according to
DCN3 MPC color caps and a new DCN3-specific function for reading MPC
data.
v3:
- remove gamut remap reg reading in favor of fixed31_32 matrix data
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
The current bandwidth calculation for timing doesn't account for
certain HDMI modes overhead which leads to DSC can't be enabled.
Add support to calculate the actual bandwidth for these HDMI modes.
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want to be able to read the MPC's gamut remap matrix similar to
what we do with .dpp_get_gamut_remap functions. On the other hand, we
don't need a hook here because only DCN3+ has the MPC gamut remap
block, being absent in previous families.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN3 DPP color state was uncollected and some state elements from DCN1
doesn't fit DCN3. Create new elements according to DCN3 color caps and
fill them up for DTN log output.
rfc-v2:
- fix reading of gamcor and blnd gamma states
- remove gamut remap register in favor of gamut remap matrix reading
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of read gamut remap data from hw values, convert HW register
values (S2D13) into a fixed-point 31.32 matrix for color state log.
Change DCN10 log to print data in the format of the gamut remap matrix.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want to be able to read the DPP's gamut remap matrix.
v2:
- code-style and doc comments clean-up (Melissa)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prepare to hook up color state log according to the DCN version.
v3:
- put functions in single line (Siqueira)
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'status' variable in 'core_link_read_dpcd()' &
'core_link_write_dpcd()' was uninitialized.
Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'.
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'.
Cc: stable@vger.kernel.org
Cc: Jerry Zuo <jerry.zuo@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the below gcc with W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_replay.c:262: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Set REPLAY power optimization flags and coasting vtotal.
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_replay.c:284: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* send Replay general cmd to DMUB.
Fixes: e379787cbc ("drm/amd/display: Add some functions for Panel Replay")
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is likely that the statement related to 'dml_edp' is misplaced. So move
it in the correct "case SIGNAL_TYPE_EDP".
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Align the returned error code with legacy DP
- Allow Z8 for multiplane configurations on DCN35
- Set default Z8 minimum residency for DCN35
- Rework DC Z10 restore
- Enable Panel Replay for static screen use case
- Add DP audio BW validation
- Fix dml2 assigned pipe search
- Ensure populate uclk in bb construction
- Update P010 scaling cap
- Reenable windowed mpo odm support
- Fix DML2 watermark calculation
- Clear OPTC mem select on disable
- Floor to mhz when requesting dpp disp clock changes to SMU
- Port DENTIST hang and TDR fixes to OTG disable W/A
- Add logging resource checks
- Add Replay IPS register for DMUB command table
- Init link enc resources in dc_state only if res_pool presents
- Allow IPS2 during Replay
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Power improvement over DCN314, but also addresses a functional issue
where plane_state remains uncleared on pipes that aren't actually
active.
[How]
Update the check to allow for zero streams to be treated as z8 allow.
Update the check to remove plane count on the active stream case.
Z8 will still be blocked based on stutter duration, which is likely to
be the case for most multi plane configurations.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call currently does two things:
1. Exits DMCUB from idle optimization if it was in
2. Checks DMCUB scratch register to determine if we need to call
DMCUB to do deferred HW restore and then sends the command if it's
ready for it.
By doing (1) we prevent driver idle from being renotified in the cases
where driver had previously allowed DC level idle optimizations via
dc_allow_idle_optimizations since it thinks:
allow == dc->idle_optimizations_allowed
...and that the operation is a no-op.
We want driver idle to be resent at the next opprotunity to do so
for video playback cases.
[How]
Migrate all usecases of dc_z10_restore to only perform (2).
Add extra calls to dc_allow_idle_optimizations to handle (1) and also
keep SW state matching with when we requested enter/exit of DMCUB
idle optimizations.
Ensure cursor idle optimizations false always get called when IPS
is supported.
Further rework/redesign is needed to decide whether we need a separate
level of DM allow vs DC allow and when to attempt re-entry.
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Timings with small HBlank (such as CVT RBv2) can result in insufficient
HBlank bandwidth for audio SDP transmission when DSC is active. This
will cause some higher bandwidth audio modes to fail.
The combination of CVT RBv2 timings + DSC can commonly be encountered
in MST scenarios.
[How]
Add DP audio bandwidth validation for 8b/10b MST and 128b/132b SST/MST
cases and filter out modes that cannot be supported with the current
timing config.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DML2 currently finds assigned pipes in array order rather than the
existing linked list order. This results in rearranging pipe order
on flip and more importantly otg inst and pipe idx mismatch.
This change preserves the order of existing pipes and guarantees
the head pipe will have matching otg inst and pipe idx.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- For some SKUs, the optimal DCFCLK for each UCLK is less than the
smallest DCFCLK STA target due to low memory bandwidth. There is
an assumption that the DCFCLK STA targets will always be less
than one of the optimal DCFCLK values, but this is not true for
SKUs that have low memory bandwidth. In this case we need to
populate the optimal UCLK for each DCFCLK STA targets as the max
UCLK freq.
- Also fix a bug in DML where start_state is not assigned and used
correctly.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
