Currently we only consider the relationship of the
old and new CDCLK frequencies when determining whether
to do the repgramming from intel_set_cdclk_pre_plane_update()
or intel_set_cdclk_post_plane_update().
It is technically possible to have a situation where the
CDCLK frequency is decreasing, but the voltage_level is
increasing due a DDI port. In this case we should bump
the voltage level already in intel_set_cdclk_pre_plane_update()
(so that the voltage_level will have been increased by the
time the port gets enabled), while leaving the CDCLK frequency
unchanged (as active planes/etc. may still depend on it).
We can then reduce the CDCLK frequency to its final value
from intel_set_cdclk_post_plane_update().
In order to handle that correctly we shall construct a
suitable amalgam of the old and new cdclk states in
intel_set_cdclk_pre_plane_update().
And we can simply call intel_set_cdclk() unconditionally
in both places as it will not do anything if nothing actually
changes vs. the current hw state.
v2: Handle cdclk_state->disable_pipes
v3: Only synchronize the cd2x update against the pipe's vblank
when the cdclk frequency is changing during the current
commit phase (Gustavo)
Cc: stable@vger.kernel.org
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240402155016.13733-3-ville.syrjala@linux.intel.com
(cherry picked from commit 34d127e2bd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently we always reprogram CDCLK from the
intel_set_cdclk_pre_plane_update() when using squash/crawl.
The code only works correctly for the cd2x update or full
modeset cases, and it was simply never updated to deal with
squash/crawl.
If the CDCLK frequency is increasing we must reprogram it
before we do anything else that might depend on the new
higher frequency, and conversely we must not decrease
the frequency until everything that might still depend
on the old higher frequency has been dealt with.
Since cdclk_state->pipe is only relevant when doing a cd2x
update we can't use it to determine the correct sequence
during squash/crawl. To that end introduce cdclk_state->disable_pipes
which simply indicates that we must perform the update
while the pipes are disable (ie. during
intel_set_cdclk_pre_plane_update()). Otherwise we use the
same old vs. new CDCLK frequency comparsiong as for cd2x
updates.
The only remaining problem case is when the voltage_level
needs to increase due to a DDI port, but the CDCLK frequency
is decreasing (and not all pipes are being disabled). The
current approach will not bump the voltage level up until
after the port has already been enabled, which is too late.
But we'll take care of that case separately.
v2: Don't break the "must disable pipes case"
v3: Keep the on stack 'pipe' for future use
Cc: stable@vger.kernel.org
Fixes: d62686ba3b ("drm/i915/adl_p: CDCLK crawl support for ADL")
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240402155016.13733-2-ville.syrjala@linux.intel.com
(cherry picked from commit 3aecee90ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since commit 0c65dc0626 ("drm/i915/jsl: s/JSL/JASPERLAKE for
platform/subplatform defines"), boot freezes on a Jasper Lake tablet
(Librem 11), usually with graphical corruption on the eDP display,
but sometimes just a black screen. This commit was included in 6.6 and
later.
That commit was intended to refactor EHL and JSL macros, but the change
to ehl_combo_pll_div_frac_wa_needed() started matching JSL incorrectly
when it was only intended to match EHL.
It replaced:
return ((IS_PLATFORM(i915, INTEL_ELKHARTLAKE) &&
IS_JSL_EHL_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
with:
return (((IS_ELKHARTLAKE(i915) || IS_JASPERLAKE(i915)) &&
IS_DISPLAY_STEP(i915, STEP_B0, STEP_FOREVER)) ||
Remove IS_JASPERLAKE() to fix the regression.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Cc: stable@vger.kernel.org
Fixes: 0c65dc0626 ("drm/i915/jsl: s/JSL/JASPERLAKE for platform/subplatform defines")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240313135424.3731410-1-jonathon.hall@puri.sm
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 1ef4885931)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Looks like the undelayed vblank gets signalled exactly when
the active period ends. That is a problem for DSB+VRR when
we are already in vblank and expect DSB to start executing
as soon as we send the push. Instead of starting, the DSB
just keeps on waiting for the undelayed vblank which won't
signal until the end of the next frame's active period,
which is far too late.
The end result is that DSB won't have even started
executing by the time the flips/etc. have completed.
We then wait for an extra 1ms, after which we terminate
the DSB and report a timeout:
[drm] *ERROR* [CRTC:80:pipe A] DSB 0 timed out waiting for idle (current head=0xfedf4000, head=0x0, tail=0x1080)
To fix this let's configure DSB to use the so called VRR
"safe window" instead of the undelayed vblank to trigger
the DSB vblank logic, when VRR is enabled.
Cc: stable@vger.kernel.org
Fixes: 34d8311f4a ("drm/i915/dsb: Re-instate DSB for LUT updates")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9927
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306040806.21697-3-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
(cherry picked from commit 41429d9b68)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reinstate commit 88b065943c ("drm/i915/dsi: Do display on
sequence later on icl+"), for the most part. Turns out some
machines (eg. Chuwi Minibook X) really do need that updated order.
It is also the order the Windows driver uses.
However we can't just undo the revert since that would again
break Lenovo 82TQ. After staring at the VBT sequences for both
machines I've concluded that the Lenovo 82TQ sequences look
somewhat broken:
- INIT_OTP is not present at all
- what should be in INIT_OTP is found in DISPLAY_ON
- what should be in DISPLAY_ON is found in BACKLIGHT_ON
(along with the actual backlight stuff)
The Chuwi Minibook X on the other hand has a full complement
of sequences in its VBT.
So let's try to deal with the broken sequences in the
Lenovo 82TQ VBT by simply swapping the (non-existent)
INIT_OTP sequence with the DISPLAY_ON sequence. Thus we
execute DISPLAY_ON when intending to execute INIT_OTP,
and execute nothing at all when intending to execute
DISPLAY_ON. That should be 100% equivalent to the
revert, for such broken VBTs.
Cc: stable@vger.kernel.org
Fixes: 6992eb815d ("Revert "drm/i915/dsi: Do display on sequence later on icl+"")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10334
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305083659.8396-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 94ae4612ea)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pull drm updates from Dave Airlie:
"Highlights are usual, more AMD IP blocks for future hw, i915/xe
changes, Displayport tunnelling support for i915, msm YUV over DP
changes, new tests for ttm, but its mostly a lot of stuff all over the
place from lots of people.
core:
- EDID cleanups
- scheduler error handling fixes
- managed: add drmm_release_action() with tests
- add ratelimited drm debug print
- DPCD PSR early transport macro
- DP tunneling and bandwidth allocation helpers
- remove built-in edids
- dp: Avoid AUX transfers on powered-down displays
- dp: Add VSC SDP helpers
cross drivers:
- use new drm print helpers
- switch to ->read_edid callback
- gem: add stats for shared buffers plus updates to amdgpu, i915, xe
syncobj:
- fixes to waiting and sleeping
ttm:
- add tests
- fix errno codes
- simply busy-placement handling
- fix page decryption
media:
- tc358743: fix v4l device registration
video:
- move all kernel parameters for video behind CONFIG_VIDEO
sound:
- remove <drm/drm_edid.h> include from header
ci:
- add tests for msm
- fix apq8016 runner
efifb:
- use copy of global screen_info state
vesafb:
- use copy of global screen_info state
simplefb:
- fix logging
bridge:
- ite-6505: fix DP link-training bug
- samsung-dsim: fix error checking in probe
- samsung-dsim: add bsh-smm-s2/pro boards
- tc358767: fix regmap usage
- imx: add i.MX8MP HDMI PVI plus DT bindings
- imx: add i.MX8MP HDMI TX plus DT bindings
- sii902x: fix probing and unregistration
- tc358767: limit pixel PLL input range
- switch to new drm_bridge_read_edid() interface
panel:
- ltk050h3146w: error-handling fixes
- panel-edp: support delay between power-on and enable; use put_sync
in unprepare; support Mediatek MT8173 Chromebooks, BOE NV116WHM-N49
V8.0, BOE NV122WUM-N41, CSO MNC207QS1-1 plus DT bindings
- panel-lvds: support EDT ETML0700Z9NDHA plus DT bindings
- panel-novatek: FRIDA FRD400B25025-A-CTK plus DT bindings
- add BOE TH101MB31IG002-28A plus DT bindings
- add EDT ETML1010G3DRA plus DT bindings
- add Novatek NT36672E LCD DSI plus DT bindings
- nt36523: support 120Hz timings, fix includes
- simple: fix display timings on RK32FN48H
- visionox-vtdr6130: fix initialization
- add Powkiddy RGB10MAX3 plus DT bindings
- st7703: support panel rotation plus DT bindings
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
panel-orientation-quirks:
- GPD Win Mini
amdgpu:
- Validate DMABuf imports in compute VMs
- Add RAS ACA framework
- PSP 13 fixes
- Misc code cleanups
- Replay fixes
- Atom interpretor PS, WS bounds checking
- DML2 fixes
- Audio fixes
- DCN 3.5 Z state fixes
- Remove deprecated ida_simple usage
- UBSAN fixes
- RAS fixes
- Enable seq64 infrastructure
- DC color block enablement
- Documentation updates
- DC documentation updates
- DMCUB updates
- ATHUB 4.1 support
- LSDMA 7.0 support
- JPEG DPG support
- IH 7.0 support
- HDP 7.0 support
- VCN 5.0 support
- SMU 13.0.6 updates
- NBIO 7.11 updates
- SDMA 6.1 updates
- MMHUB 3.3 updates
- DCN 3.5.1 support
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Validate DMABuf imports in compute VMs
- SVM fixes
- Trap handler updates and enhancements
- Fix cache size reporting
- Relocate the trap handler
radeon:
- Atom interpretor PS, WS bounds checking
- Misc code cleanups
xe:
- new query for GuC submission version
- Remove unused persistent exec_queues
- Add vram frequency sysfs attributes
- Add the flag XE_VM_BIND_FLAG_DUMPABLE
- Drop pre-production workarounds
- Drop kunit tests for unsupported platforms
- Start pumbling SR-IOV support with memory based interrupts for VF
- Allow to map BO in GGTT with PAT index corresponding to XE_CACHE_UC
to work with memory based interrupts
- Add GuC Doorbells Manager as prep work SR-IOV
- Implement additional workarounds for xe2 and MTL
- Program a few registers according to perfomance guide spec for Xe2
- Fix remaining 32b build issues and enable it back
- Fix build with CONFIG_DEBUG_FS=n
- Fix warnings from GuC ABI headers
- Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF
- Release mmap mappings on rpm suspend
- Disable mid-thread preemption when not properly supported by
hardware
- Fix xe_exec by reserving extra fence slot for CPU bind
- Fix xe_exec with full long running exec queue
- Canonicalize addresses where needed for Xe2 and add to devcoredum
- Toggle USM support for Xe2
- Only allow 1 ufence per exec / bind IOCTL
- Add GuC firmware loading for Lunar Lake
- Add XE_VMA_PTE_64K VMA flag
i915:
- Add more ADL-N PCI IDs
- Enable fastboot also on older platforms
- Early transport for panel replay and PSR
- New ARL PCI IDs
- DP TPS4 PHY test pattern support
- Unify and improve VSC SDP for PSR and non-PSR cases
- Refactor memory regions and improve debug logging
- Rework global state serialization
- Remove unused CDCLK divider fields
- Unify HDCP connector logging format
- Use display instead of graphics version in display code
- Move VBT and opregion debugfs next to the implementation
- Abstract opregion interface, use opaque type
- MTL fixes
- HPD handling fixes
- Add GuC submission interface version query
- Atomically invalidate userptr on mmu-notifier
- Update handling of MMIO triggered reports
- Don't make assumptions about intel_wakeref_t type
- Extend driver code of Xe_LPG to Xe_LPG+
- Add flex arrays to struct i915_syncmap
- Allow for very slow HuC loading
- DP tunneling and bandwidth allocation support
msm:
- Correct bindings for MSM8976 and SM8650 platforms
- Start migration of MDP5 platforms to DPU driver
- X1E80100 MDSS support
- DPU:
- Improve DSC allocation, fixing several important corner cases
- Add support for SDM630/SDM660 platforms
- Simplify dpu_encoder_phys_ops
- Apply fixes targeting DSC support with a single DSC encoder
- Apply fixes for HCTL_EN timing configuration
- X1E80100 support
- Add support for YUV420 over DP
- GPU:
- fix sc7180 UBWC config
- fix a7xx LLC config
- new gpu support: a305B, a750, a702
- machine support: SM7150 (different power levels than other a618)
- a7xx devcoredump support
habanalabs:
- configure IRQ affinity according to NUMA node
- move HBM MMU page tables inside the HBM
- improve device reset
- check extended PCIe errors
ivpu:
- updates to firmware API
- refactor BO allocation
imx:
- use devm_ functions during init
hisilicon:
- fix EDID includes
mgag200:
- improve ioremap usage
- convert to struct drm_edid
- Work around PCI write bursts
nouveau:
- disp: use kmemdup()
- fix EDID includes
- documentation fixes
qaic:
- fixes to BO handling
- make use of DRM managed release
- fix order of remove operations
rockchip:
- analogix_dp: get encoder port from DT
- inno_hdmi: support HDMI for RK3128
- lvds: error-handling fixes
ssd130x:
- support SSD133x plus DT bindings
tegra:
- fix error handling
tilcdc:
- make use of DRM managed release
v3d:
- show memory stats in debugfs
- Support display MMU page size
vc4:
- fix error handling in plane prepare_fb
- fix framebuffer test in plane helpers
virtio:
- add venus capset defines
vkms:
- fix OOB access when programming the LUT
- Kconfig improvements
vmwgfx:
- unmap surface before changing plane state
- fix memory leak in error handling
- documentation fixes
- list command SVGA_3D_CMD_DEFINE_GB_SURFACE_V4 as invalid
- fix null-pointer deref in execbuf
- refactor display-mode probing
- fix fencing for creating cursor MOBs
- fix cursor-memory lifetime
xlnx:
- fix live video input for ZynqMP DPSUB
lima:
- fix memory leak
loongson:
- fail if no VRAM present
meson:
- switch to new drm_bridge_read_edid() interface
renesas:
- add RZ/G2L DU support plus DT bindings
mxsfb:
- Use managed mode config
sun4i:
- HDMI: updates to atomic mode setting
mediatek:
- Add display driver for MT8188 VDOSYS1
- DSI driver cleanups
- Filter modes according to hardware capability
- Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
etnaviv:
- enhancements for NPU and MRT support"
* tag 'drm-next-2024-03-13' of https://gitlab.freedesktop.org/drm/kernel: (1420 commits)
drm/amd/display: Removed redundant @ symbol to fix kernel-doc warnings in -next repo
drm/amd/pm: wait for completion of the EnableGfxImu message
drm/amdgpu/soc21: add mode2 asic reset for SMU IP v14.0.1
drm/amdgpu: add smu 14.0.1 support
drm/amdgpu: add VPE 6.1.1 discovery support
drm/amdgpu/vpe: add VPE 6.1.1 support
drm/amdgpu/vpe: don't emit cond exec command under collaborate mode
drm/amdgpu/vpe: add collaborate mode support for VPE
drm/amdgpu/vpe: add PRED_EXE and COLLAB_SYNC OPCODE
drm/amdgpu/vpe: add multi instance VPE support
drm/amdgpu/discovery: add nbif v6_3_1 ip block
drm/amdgpu: Add nbif v6_3_1 ip block support
drm/amdgpu: Add pcie v6_1_0 ip headers (v5)
drm/amdgpu: Add nbif v6_3_1 ip headers (v5)
arch/powerpc: Remove <linux/fb.h> from backlight code
macintosh/via-pmu-backlight: Include <linux/backlight.h>
fbdev/chipsfb: Include <linux/backlight.h>
drm/etnaviv: Restore some id values
drm/amdkfd: make kfd_class constant
drm/amdgpu: add ring timeout information in devcoredump
...
The icl+ power well code currently assumes that every AUX power
well maps to an encoder which is using said power well. That is
by no menas guaranteed as we:
- only register encoders for ports declared in the VBT
- combo PHY HDMI-only encoder no longer get an AUX CH since
commit 9856308c94 ("drm/i915: Only populate aux_ch if really needed")
However we have places such as intel_power_domains_sanitize_state()
that blindly traverse all the possible power wells. So these bits
of code may very well encounbter an aux power well with no associated
encoder.
In this particular case the BIOS seems to have left one AUX power
well enabled even though we're dealing with a HDMI only encoder
on a combo PHY. We then proceed to turn off said power well and
explode when we can't find a matching encoder. As a short term fix
we should be able to just skip the PHY related parts of the power
well programming since we know this situation can only happen with
combo PHYs.
Another option might be to go back to always picking an AUX CH for
all encoders. However I'm a bit wary about that since we might in
theory end up conflicting with the VBT AUX CH assignment. Also
that wouldn't help with encoders not declared in the VBT, should
we ever need to poke the corresponding power wells.
Longer term we need to figure out what the actual relationship
is between the PHY vs. AUX CH vs. AUX power well. Currently this
is entirely unclear.
Cc: stable@vger.kernel.org
Fixes: 9856308c94 ("drm/i915: Only populate aux_ch if really needed")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10184
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223203216.15210-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 6a8c66bf0e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The TBT DP tunnel BW request logic in the Thunderbolt Connection Manager
depends on the GFX driver reading out the sink's DPRX capabilities in
response to a long HPD pulse. Since in i915 this read-out can be blocked
by another connector's/encoder's hotplug event handling (which is
serialized by drm_mode_config::connection_mutex), do a dummy DPRX read-out
in the encoder's HPD pulse handler (which is not blocked by other
encoders).
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-21-imre.deak@intel.com
Suspend and resume DP tunnels during system suspend/resume, disabling
the BW allocation mode during suspend, re-enabling it after resume. This
reflects the link's BW management component (Thunderbolt CM) disabling
BWA during suspend. Before any BW requests the driver must read the
sink's DPRX capabilities (since the BW manager requires this
information, so snoops for it on AUX), so ensure this read takes place.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-20-imre.deak@intel.com
Add the atomic state during a modeset required to enable the DP tunnel
BW allocation mode on links where such a tunnel was detected. This state
applies to an already enabled output, the state added for a newly
enabled output will be computed and added/cleared to/from the atomic
state in a follow-up patch.
v2:
- s/old_crtc_state/crtc_state in intel_crtc_duplicate_state().
- Move intel_dp_tunnel_atomic_cleanup_inherited_state() to a follow-up
patch adding the corresponding state. (Ville)
- Move intel_dp_tunnel_atomic_clear_stream_bw() to a follow-up
patch adding the corresponding state.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-14-imre.deak@intel.com
Add support to enable the DP tunnel BW allocation mode. Follow-up
patches will call the required helpers added here to prepare for a
modeset on a link with DP tunnels, the last change in the patchset
actually enabling BWA.
With BWA enabled, the driver will expose the full mode list a display
supports, regardless of any BW limitation on a shared (Thunderbolt)
link. Such BW limits will be checked against only during a modeset, when
the driver has the full knowledge of each display's BW requirement.
If the link BW changes in a way that a connector's modelist may also
change, userspace will get a hotplug notification for all the connectors
sharing the same link (so it can adjust the mode used for a display).
The BW limitation can change at any point, asynchronously to modesets
on a given connector, so a modeset can fail even though the atomic check
for it passed. In such scenarios userspace will get a bad link
notification and in response is supposed to retry the modeset.
v2:
- Fix old vs. new connector state in intel_dp_tunnel_atomic_check_state().
(Ville)
- Fix propagating the error from
intel_dp_tunnel_atomic_compute_stream_bw(). (Ville)
- Move tunnel==NULL checks from driver to DRM core helpers. (Ville)
- Simplify return flow from intel_dp_tunnel_detect(). (Ville)
- s/dp_tunnel_state/inherited_dp_tunnels (Ville)
- Simplify struct intel_dp_tunnel_inherited_state. (Ville)
- Unconstify object pointers (vs. states) where possible. (Ville)
- Init crtc_state while declaring it in check_group_state(). (Ville)
- Join obj->base.id, obj->name arg lines in debug prints to reduce LOC.
(Ville)
- Add/rework intel_dp_tunnel_atomic_alloc_bw() to prepare for moving the
BW allocation from encoder hooks up to intel_atomic_commit_tail()
later in the patchset.
- Disable BW alloc mode during system suspend.
- Allocate the required BW for all tunnels during system resume.
- Add intel_dp_tunnel_atomic_clear_stream_bw() instead of the open-coded
sequence in a follow-up patch.
- Add function documentation to all exported functions.
- Add CONFIG_USB4 dependency to CONFIG_DRM_I915_DP_TUNNEL.
v3:
- Rebase on intel_dp_get_active_pipes() change in previous patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-4-imre.deak@intel.com
Sync instead of only try-sync non-blocking commits when getting the
active pipes through a given DP port. Atm intel_dp_get_active_pipes()
will only try to sync a given pipe and if that would block ignore the
pipe. This was supposed to avoid link retraining in case a pending
modeset would do that anyway, however that could incorrectly ignore
fastset pipes as well for instance (which don't retraing the link).
The TC port reset path needs to handle all pipes, even if a waiting for
a pending commit would block. To account for the above cases sync all
the pipes unconditionally.
This also prepares for a follow-up change enabling the DP tunnel BW
allocation mode which needs to ensure that all active pipes are synced
and returned from intel_dp_get_active_pipes().
v2:
- Add a separate function to try-sync the pipes. (Ville)
v3:
- Just sync the pipes unconditionally in intel_dp_get_active_pipes().
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-3-imre.deak@intel.com
On shared (Thunderbolt) links with DP tunnels, the modeset may need to
be retried on all connectors on the link due to a link BW limitation
arising only after the atomic check phase. To support this add a helper
function queuing a work to retry the modeset on a given port's connector
and at the same time any MST connector with streams through the same
port. A follow-up change enabling the DP tunnel Bandwidth Allocation
Mode will take this into use.
v2:
- Send the uevent only to enabled MST connectors. (Jouni)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-5-imre.deak@intel.com
