At the moment modesetting pipe C on IVB will fail if pipe B uses 4 FDI
lanes. Make the BW sharing more dynamic by trying to reduce pipe B's
link bpp in this case, until pipe B uses only up to 2 FDI lanes.
For this instead of the encoder compute config retry loop - which
reduced link bpp only for the encoder's pipe - reduce the maximum link
bpp for pipe B/C as required after all CRTC states are computed and
recompute the CRTC states with the new bpp limit.
Atm, all FDI encoder's compute config function returns an error if a BW
constrain prevents increasing the pipe bpp value. The corresponding
crtc_state->bw_constrained check can be replaced with checking
crtc_state->max_link_bpp_x16, add TODO comments for this. SDVO is an
exception where this case is only handled in the outer config retry
loop, failing the modeset with a WARN, add a FIXME comment to handle
this in the encoder code similarly to other encoders.
v2:
- Don't assume that a CRTC is already in the atomic state, while
reducing its link bpp.
- Add DocBook description to intel_fdi_atomic_check_link().
v3:
- Enable BW management for FDI links in a separate patch. (Ville)
v4: (Ville)
- Fail the SDVO encoder config computation if it doesn't support the
link bpp limit.
- Add TODO: comments about checking link_bpp_x16 instead of
bw_constrained.
v5:
- Replace link bpp limit check with a FIXME: comment in
intel_sdvo_compute_config(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Amended commit message wrt. changes in v5]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921195159.2646027-11-imre.deak@intel.com
In non-DSC mode the link bpp can be set in 2*3 bpp steps in the pipe bpp
range, while in DSC mode it can be set in 1/16 bpp steps to any value
up to the maximum pipe bpp. Update the limits accordingly in both modes
to prepare for a follow-up patch which may need to reduce the max link
bpp value and starts to check the link bpp limits in DSC mode as well.
While at it add more detail to the link limit debug print and print it
also for DSC mode.
v2:
- Add to_bpp_frac_dec() instead of open coding it. (Jani)
v3: (Ville)
- Add BPP_X16_FMT / BPP_X16_ARG.
- Add TODO: comment about initializing the DSC link bpp limits earlier.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921195159.2646027-5-imre.deak@intel.com
A follow-up patch will need to limit the output link bpp both in the
non-DSC and DSC configuration, so track the pipe and link bpp limits
separately in the link_config_limits struct.
Use .4 fixed point format for link bpp matching the 1/16 bpp granularity
in DSC mode and for now keep this limit matching the pipe bpp limit.
v2: (Jani)
- Add to_bpp_int(), to_bpp_x16() helpers instead of opencoding them.
- Rename link_config_limits::link.min/max_bpp to min/max_bpp_x16.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921195159.2646027-3-imre.deak@intel.com
Make the seamless_m_n flag more like the update_pipe fastset
flag, ie. the flag will only be set if we need to do the seamless
M/N update, and in all other cases the flag is cleared. Also
rename the flag to update_m_n to make it more clear it's similar
to update_pipe.
I believe special casing seamless_m_n like this makes sense
as it also affects eg. vblank evasion. We can potentially avoid
some vblank evasion tricks, simplify some checks, and hopefully
will help with the VRR vs. M/N mess.
Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901130440.2085-6-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Apparently Acer Chromebook C740 (BDW-ULT) doesn't have the
eDP HPD line properly connected, and thus fails the new
HPD check during eDP probe. The result is that we lose the
eDP output.
I suspect all such machines would be Chromebooks or other
Linux exclusive systems as the Windows driver likely wouldn't
work either. I did check a few other BDW machines here and
those do have eDP HPD connected, one of them even is a
different Chromebook (Samus).
To account for these funky machines let's skip the HPD check when
it looks like the eDP port is the only one using that specific AUX
channel. In case of multiple ports sharing the same AUX CH (eg. on
Asrock B250M-HDV) we still do the check and thus should correctly
ignore the eDP port in favor of the other DP port (usually a DP->VGA
converter).
v2: Don't oops during list iteration
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9264
Fixes: cfe5bdfb27 ("drm/i915: Check HPD live state during eDP probe")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230908052527.685-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Currently, we take the max lane, rate and pipe bpp, to get the maximum
compressed bpp possible. We then set the output bpp to this value.
This patch provides support to have max bpp, min rate and min lanes,
that can support the min compressed bpp.
v2:
-Avoid ending up with compressed bpp, same as pipe bpp. (Stan)
-Fix the checks for limits->max/min_bpp while iterating over list of
valid DSC bpcs. (Stan)
v3:
-Refactor the code to have pipe bpp/compressed bpp computation and slice
count calculation separately for different cases.
v4:
-Separate the pipe_bpp calculation for eDP and DP.
v5:
-Get rid of magic numbers for max and min bpp,
and improve documentation. (Stan).
-Use functions for {src_sink}_{min_max}_compressed_bpp (Ville).
v6:
-Remove lines to set link config to max.
v7:
-Split the part to separate edp and dp functions for computing DSC BPP
into separate patch.
v8:
-Separate mechanism to get compressed bpp for ICL,TGL and XELPD+.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230817142459.89764-17-ankit.k.nautiyal@intel.com
Currently there are many places where we use output_bpp for link bpp and
compressed bpp.
Lets use consistent naming:
output_bpp : The intermediate value taking into account the
output_format chroma subsampling.
compressed_bpp : target bpp for the DSC encoder.
link_bpp : final bpp used in the link.
For 444 sampling without DSC:
link_bpp = output_bpp = pipe_bpp
For 420 sampling without DSC:
output_bpp = pipe_bpp / 2
link_bpp = output_bpp
For 444 sampling with DSC:
output_bpp = pipe_bpp
link_bpp = compressed_bpp, computed with output_bpp (i.e. pipe_bpp in
this case)
For 420 sampling with DSC:
output_bpp = pipe_bpp/2
link_bpp = compressed_bpp, computed with output_bpp
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230817142459.89764-5-ankit.k.nautiyal@intel.com
The issue fixed in
commit a8ddac7c9f ("drm/i915: Avoid HPD poll detect triggering a new detect cycle")
on VLV, CHV is still present on platforms where the display hotplug
detection functionality is available whenever the device is in D0 state
(hence these platforms switch to HPD polling only when the device is
runtime suspended).
The above commit avoids an endless i915_hpd_poll_init_work() ->
connector detect loop by making sure that by the end of
i915_hpd_poll_init_work() all display power references acquired by the
connector detect functions which can trigger a new cycle (display core
power domain) are dropped. However on platforms where HPD polling is
enabled/disabled only from the runtime suspend/resume handlers, this is
not ensured: for instance eDP VDD, TypeC port PHYs and the runtime
autosuspend delay may still keep the device runtime resumed (via a power
reference acquired during connector detection and hence result in an
endless loop like the above).
Solve the problem described in the above commit on all platforms, by
making sure that a i915_hpd_poll_init_work() -> connector detect
sequence can't take any power reference in the first place which would
trigger a new cycle, instead of relying on these power references to be
dropped by the end of the sequence.
With the default runtime autosuspend delay (10 sec) this issue didn't
happen in practice, since the device remained runtime resumed for the
whole duration of the above sequence. CI/IGT tests however set the
autosuspend delay to 0, which makes the problem visible, see References:
below.
Tested on GLK, CHV.
v2: Don't warn about a requeued work, to account for disabling
polling directly during driver loading, reset and system resume.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/7940#note_1997403
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230809104307.1218058-1-imre.deak@intel.com
- Removing unused declarations (Arnd, Gustavo)
- ICL+ DSI modeset sequence fixes (Ville)
- Improvements on HDCP (Suraj)
- Fixes and clean up on MTL Display (Mika Kahola, Lee, RK, Nirmoy, Chaitanya)
- Restore HSW/BDW PSR1 (Ville)
- Other PSR Fixes (Jouni)
- Fixes around DC states and other Display Power (Imre)
- Init DDI ports in VBT order (Ville)
- General documentation fixes (Jani)
- General refactor for better organization (Jani)
- Bigjoiner fix (Stanislav)
- VDSC Fixes and improvements (Stanialav, Suraj)
- Hotplug fixes and improvements (Simon, Suraj)
- Start using plane scale factor for relative data rate (Stanislav)
- Use shmem for dpt objects (RK)
- Simplify expression &to_i915(dev)->drm (Uwe)
- Do not access i915_gem_object members from frontbuffer tracking (Jouni)
- Fix uncore race around i915->params.mmio_debug (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZMv4RCzGyCmG/BDe@intel.com
Currently we just clamp that value to the highest supported one, however that
means, we are not able to fit this into our available bandwidth range, so we
might see glitches or FIFO underruns.
While choosing less compressed bpp than min bpp required to handle the mode is
harmless and might even save some bandwidth, choosing higher compressed bpp than
min bpp required to handle the required mode config, can cause issues.
So in that case lets just conclude that even with DSC, we are not able to comply
with bandwidth requirements and fail.
v2: - s/clamp_t/min_t/ (Luca Coelho)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230629122534.8815-1-stanislav.lisovskiy@intel.com
[Why]
The sequence for collecting down_reply from source perspective should
be:
Request_n->repeat (get partial reply of Request_n->clear message ready
flag to ack DPRX that the message is received) till all partial
replies for Request_n are received->new Request_n+1.
Now there is chance that drm_dp_mst_hpd_irq() will fire new down
request in the tx queue when the down reply is incomplete. Source is
restricted to generate interveleaved message transactions so we should
avoid it.
Also, while assembling partial reply packets, reading out DPCD DOWN_REP
Sideband MSG buffer + clearing DOWN_REP_MSG_RDY flag should be
wrapped up as a complete operation for reading out a reply packet.
Kicking off a new request before clearing DOWN_REP_MSG_RDY flag might
be risky. e.g. If the reply of the new request has overwritten the
DPRX DOWN_REP Sideband MSG buffer before source writing one to clear
DOWN_REP_MSG_RDY flag, source then unintentionally flushes the reply
for the new request. Should handle the up request in the same way.
[How]
Separete drm_dp_mst_hpd_irq() into 2 steps. After acking the MST IRQ
event, driver calls drm_dp_mst_hpd_irq_send_new_request() and might
trigger drm_dp_mst_kick_tx() only when there is no on going message
transaction.
Changes since v1:
* Reworked on review comments received
-> Adjust the fix to let driver explicitly kick off new down request
when mst irq event is handled and acked
-> Adjust the commit message
Changes since v2:
* Adjust the commit message
* Adjust the naming of the divided 2 functions and add a new input
parameter "ack".
* Adjust code flow as per review comments.
Changes since v3:
* Update the function description of drm_dp_mst_hpd_irq_handle_event
Changes since v4:
* Change ack of drm_dp_mst_hpd_irq_handle_event() to be an array align
the size of esi[]
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
