The WA states that we need to alert the GSC FW before doing a GSC engine
reset and then wait for 200ms. The GuC owns engine reset, so on the i915
side we only need to apply this for full GT reset.
Given that we do full GT resets in the resume paths to cleanup the HW
state and that a long wait in those scenarios would not be acceptable,
a faster path has been introduced where, if the GSC is idle, we try first
to individually reset the GuC and all engines except the GSC and only fall
back to full reset if that fails.
Note: according to the WA specs, if the GSC is idle it should be possible
to only wait for the uC wakeup time (~15ms) instead of the whole 200ms.
However, the GSC FW team have mentioned that the wakeup time can change
based on other things going on in the HW and pcode, so a good security
margin would be required. Given that when the GSC is idle we already
skip the wait & reset entirely and that this reduced wait would still
likely be too long to use in resume paths, it's not worth adding support
for this reduced wait.
v2: add comment to explain why it is safe to skip the GSC reset (John)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323231857.2194435-2-daniele.ceraolospurio@intel.com
Driver Changes:
- Fix issue #6333: "list_add corruption" and full system lockup from
performance monitoring (Janusz)
- Give the punit time to settle before fatally failing (Aravind, Chris)
- Don't use stolen memory or BAR for ring buffers on LLC platforms (John)
- Add missing ecodes and correct timeline seqno on GuC error captures (John)
- Make sure DSM size has correct 1MiB granularity on Gen12+ (Nirmoy,
Lucas)
- Fix potential SSEU max_subslices array-index-out-of-bounds access on Gen11 (Andrea)
- Whitelist COMMON_SLICE_CHICKEN3 for UMD access on Gen12+ (Matt R.)
- Apply Wa_1408615072/Wa_1407596294 correctly on Gen11 (Matt R)
- Apply LNCF/LBCF workarounds correctly on XeHP SDV/PVC/DG2 (Matt R)
- Implement Wa_1606376872 for Xe_LP (Gustavo)
- Consider GSI offset when doing MCR lookups on Meteorlake+ (Matt R.)
- Add engine TLB invalidation for Meteorlake (Matt R.)
- Fix GSC Driver-FLR completion on Meteorlake (Alan)
- Fix GSC races on driver load/unload on Meteorlake+ (Daniele)
- Disable MC6 for MTL A step (Badal)
- Consolidate TLB invalidation flow (Tvrtko)
- Improve debug GuC/HuC debug messages (Michal Wa., John)
- Move fd_install after last use of fence (Rob)
- Initialize the obj flags for shmem objects (Aravind)
- Fix missing debug object activation (Nirmoy)
- Probe lmem before the stolen portion (Matt A)
- Improve clean up of GuC busyness stats worker (John)
- Fix missing return code checks in GuC submission init (John)
- Annotate two more workaround/tuning registers as MCR on PVC (Matt R)
- Fix GEN8_MISCCPCTL definition and remove unused INF_UNIT_LEVEL_CLKGATE (Lucas)
- Use sysfs_emit() and sysfs_emit_at() (Nirmoy)
- Make kobj_type structures constant (Thomas W.)
- make kobj attributes const on gt/ (Jani)
- Remove the unused virtualized start hack on buddy allocator (Matt A)
- Remove redundant check for DG1 (Lucas)
- Move DG2 tuning to the right function (Lucas)
- Rename dev_priv to i915 for private data naming consistency in gt/ (Andi)
- Remove unnecessary whitelisting of CS_CTX_TIMESTAMP on Xe_HP platforms (Matt R.)
-
- Escape wildcard in method names in kerneldoc (Bagas)
- Selftest improvements (Chris, Jonathan, Tvrtko, Anshuman, Tejas)
- Fix sparse warnings (Jani)
[airlied: fix unused variable in intel_workarounds]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZBMSb42yjjzczRhj@jlahtine-mobl.ger.corp.intel.com
Add definitions for various pipe timestamp registers:
- frame timestamp (last start of vblank) (g4x+), already had this defined
- flip timestamp (when SURF was last written) (g4x+)
- flipdone timestamp (when last flipdone was signalled) (tgl+)
Note that on pre-tgl the flip related timestamps are only updated
for primary plane flips, but on tgl+ we can select which plane
updates them (via PIPE_MISC2). Let's define those related bits
as well.
Curiously VLV/CHV do not have the frame/flip timestamp registers,
despite all the other related registers being inherited from g4x.
This means we can get rid of the pipe_offsets[] usage for these,
and thus the implicit dev_priv is gone as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230314130255.23273-4-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
The Wa_14017073508 require to send Media Busy/Idle mailbox while
accessing Media tile. As of now it is getting handled while __gt_unpark,
__gt_park. But there are various corner cases where forcewakes are taken
without __gt_unpark i.e. without sending Busy Mailbox especially during
register reads. Forcewakes are taken without busy mailbox leads to
GPU HANG. So bringing mailbox calls under forcewake calls are no feasible
option as forcewake calls are atomic and mailbox calls are blocking.
The issue already fixed in B step so disabling MC6 on A step and
reverting previous commit which handles Wa_14017073508
Fixes: 8f70f1ec58 ("drm/i915/mtl: Add Wa_14017073508 for SAMedia")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Badal Nilawar <badal.nilawar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230310061339.2495416-2-badal.nilawar@intel.com
The idea that ctg uses different HPD live state bits is
total nonsense, at least on my machine (Dell Latitude
E5400).
The only reason DP-B even works on my ctg is that DP-D
live state is stuck high, even though there is no physical
DP-D port. So when the detect checks DP-B live state it
sees the stuck live state of DP-D instead. If I hack
the driver to not register DP-D at all, and thus we never
enabe DP-D HPD, DP-B stops working as well.
Just to put some conclusive evidence into this mess,
here are the actual hotplug register values for each port:
Everything disconnected:
PORT_HOTPLUG_EN (0x00061110): 0x00000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
PORT_HOTPLUG_EN (0x00061110): 0x08000000
PORT_HOTPLUG_STAT (0x00061114): 0x08000000
PORT_HOTPLUG_EN (0x00061110): 0x10000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
PORT_HOTPLUG_EN (0x00061110): 0x20000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
Only port B connected:
PORT_HOTPLUG_EN (0x00061110): 0x00000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
PORT_HOTPLUG_EN (0x00061110): 0x08000000
PORT_HOTPLUG_STAT (0x00061114): 0x08000000
PORT_HOTPLUG_EN (0x00061110): 0x10000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
PORT_HOTPLUG_EN (0x00061110): 0x20000000
PORT_HOTPLUG_STAT (0x00061114): 0x20000000
Only port C connected:
PORT_HOTPLUG_EN (0x00061110): 0x00000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
PORT_HOTPLUG_EN (0x00061110): 0x08000000
PORT_HOTPLUG_STAT (0x00061114): 0x08000000
PORT_HOTPLUG_EN (0x00061110): 0x10000000
PORT_HOTPLUG_STAT (0x00061114): 0x10000000
PORT_HOTPLUG_EN (0x00061110): 0x20000000
PORT_HOTPLUG_STAT (0x00061114): 0x00000000
So the enable bit and live state bit always match 1:1.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302161013.29213-4-ville.syrjala@linux.intel.com
Define the contents of the transcoder timing registers using
REG_GENMASK() & co. For ease of maintenance let's just define
the bitmasks with the full 16bit width (also used by the
current hand rolled stuff) even though not all bits are actually
used. None of the unsued bits have ever contained anything.
Jani spotted that the CRT load detection code did use narrower
bitmasks, so that is now going to change. But that is fine
since any garbage in the high bits would have been caught by
the state checker that always used the full 16bit masks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Name the CPU transcoder timing registers TRANS_FOO rather than
just FOO. This is the modern name, after the pipe/transcoder split
happened. Makes it a bit more obvious whether you pass in a pipe or
a transcoder.
PIPESRC is a bit special as it's a pipe register, even though it
lives in the transcoder registers range (0x60000 instead of 0x70000).
And BCLRPAT I suppose is a transcoder register (since it has something
to do with the timing generator), but it doesn't even exist after gen4
so I left it to use the only name it ever had in bspec.
And while at it let's pass in the correct enum in few more
places why don't we. Although in all those places the distinction
doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Avoid the array lookup, converting the PLL macros after ICL to
_PICK_EVEN_RANGES. This provides the following reduction in code size:
$ size build64/drivers/gpu/drm/i915/i915.o{.old,.new}
text data bss dec hex filename
4027456 185703 6984 4220143 4064ef build64/drivers/gpu/drm/i915/i915.o.old
4026997 185703 6984 4219684 406324 build64/drivers/gpu/drm/i915/i915.o.new
At the same time it's safer, avoiding out-of-bounds array access. This
allows to remove _MMIO_PLL3() that is now unused.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-4-lucas.demarchi@intel.com
Lets eradicate a silent conflict between drm-intel-next and
drm-intel-gt-next which added a duplicate function (try_firmware_load).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Driver Changes:
Fixes/improvements/new stuff:
- Fix workarounds on Gen2-3 (Tvrtko Ursulin)
- Fix HuC delayed load memory leaks (Daniele Ceraolo Spurio)
- Fix a BUG caused by impendance mismatch in dma_fence_wait_timeout and GuC (Janusz Krzysztofik)
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663 (Matt Atwood)
- Apply recommended L3 hashing mask tuning parameters (Gen12+) (Matt Roper)
- Improve suspend / resume times with VT-d scanout workaround active (Andi Shyti, Chris Wilson)
- Silence misleading "mailbox access failed" warning in snb_pcode_read (Ashutosh Dixit)
- Fix null pointer dereference on HSW perf/OA (Umesh Nerlige Ramappa)
- Avoid trampling the ring during buffer migration (and selftests) (Chris Wilson, Matthew Auld)
- Fix DG2 visual corruption on small BAR systems by not forgetting to copy CCS aux state (Matthew Auld)
- More fixing of DG2 visual corruption by not forgetting to copy CCS aux state of backup objects (Matthew Auld)
- Fix TLB invalidation for Gen12.50 video and compute engines (Andrzej Hajda)
- Limit Wa_22012654132 to just specific steppings (Matt Roper)
- Fix userspace crashes due eviction not working under lock contention after the object locking conversion (Matthew Auld)
- Avoid double free is user deploys a corrupt GuC firmware (John Harrison)
- Fix 32-bit builds by using "%zu" to format size_t (Nirmoy Das)
- Fix a possible BUG in TTM async unbind due not reserving enough fence slots (Nirmoy Das)
- Fix potential use after free by not exposing the GEM context id to userspace too early (Rob Clark)
- Show clamped PL1 limit to the user (hwmon) (Ashutosh Dixit)
- Workaround unreliable reset on Jasperlake (Chris Wilson)
- Cover rest of SVG unit MCR registers (Gustavo Sousa)
- Avoid PXP log spam on platforms which do not support the feature (Alan Previn)
- Re-disable RC6p on Sandy Bridge to avoid GPU hangs and visual glitches (Sasa Dragic)
Future platform enablement:
- Manage uncore->lock while waiting on MCR register (Matt Roper)
- Enable Idle Messaging for GSC CS (Vinay Belgaumkar)
- Only initialize GSC in tile 0 (José Roberto de Souza)
- Media GT and Render GT share common GGTT (Aravind Iddamsetty)
- Add dedicated MCR lock (Matt Roper)
- Implement recommended caching policy (PVC) (Wayne Boyer)
- Add hardware-level lock for steering (Matt Roper)
- Check full IP version when applying hw steering semaphore (Matt Roper)
- Enable GuC GGTT invalidation from the start (Daniele Ceraolo Spurio)
- MTL GSC firmware support (Daniele Ceraolo Spurio, Jonathan Cavitt)
- MTL OA support (Umesh Nerlige Ramappa)
- MTL initial gt workarounds (Matt Roper)
Driver refactors:
- Hold forcewake and MCR lock over PPAT setup (Matt Roper)
- Acquire fw before loop in intel_uncore_read64_2x32 (Umesh Nerlige Ramappa)
- GuC filename cleanups and use submission API version number (John Harrison)
- Promote pxp subsystem to top-level of i915 (Alan Previn)
- Finish proofing the code agains object size overflows (Chris Wilson, Gwan-gyeong Mun)
- Start adding module oriented dmesg output (John Harrison)
Miscellaneous:
- Correct kerneldoc for intel_gt_mcr_wait_for_reg() (Matt Roper)
- Bump up sample period for busy stats selftest (Umesh Nerlige Ramappa)
- Make GuC default_lists const data (Jani Nikula)
- Fix table order verification to check all FW types (John Harrison)
- Remove some limited use register access wrappers (Jani Nikula)
- Remove struct_member macro (Andrzej Hajda)
- Remove hardcoded value with a macro (Nirmoy Das)
- Use helper func to find out map type (Nirmoy Das)
- Fix a static analysis warning (John Harrison)
- Consolidate VMA active tracking helpers (Andrzej Hajda)
- Do not cover all future platforms in TLB invalidation (Tvrtko Ursulin)
- Replace zero-length arrays with flexible-array members (Gustavo A. R. Silva)
- Unwind hugepages to drop wakeref on error (Chris Wilson)
- Remove a couple of superfluous i915_drm.h includes (Jani Nikula)
Merges:
- Merge drm/drm-next into drm-intel-gt-next (Rodrigo Vivi)
danvet: Fix up merge conflict in intel_uc_fw.c, we ended up with 2
copies of try_firmware_load() somehow.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y8fW2Ny1B1hZ5ZmF@tursulin-desk
The implementation of Wa_22011450934 introduced three new register
definitions in i915_reg.h that didn't get moved to the GT/engine
register headers when all the other registers moved; let's move them to
the appropriate headers and tidy up their definitions now for
consistency:
- STATE_ACK_DEBUG is moved to the engine register header and converted
to a parameterized definition; the workaround only needs the RCS
instance to be programmed, but there are instances on other engines
that could be used by other workarounds in the future.
- The two CULLBIT registers move to the GT register header. Since
they belong to MMIO ranges that became MCR starting with Xe_HP,
their definitions should be defined as MCR_REG() and use an Xe_HP
prefix to keep the register semantics clear.
Note that the MCR definition is just for consistency and to prevent
accidental misuse if other workarounds related to these registers show
up in the future. There's no functional change to today's driver since
the workaround that references these registers only accesses them via
MI_LRR engine instructions. Engine-initiated register accesses do not
utilize the same steering controls as CPU-initiated accesses; they
use a different steering control register (0x20CC) which is initialized
to a non-terminated DSS target by pre-OS firmware and never changed
thereafter (i915 does not touch it and userspace does not have
permission to change that register).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230117202627.4134579-1-matthew.d.roper@intel.com
