Bits to enable/disable and check state for D2D moved from
XELPDP_PORT_BUF_CTL1 to DDI_BUF_CTL (now named DDI_CTL_DE in the spec).
Make the functions mtl_ddi_disable_d2d() and mtl_ddi_enable_d2d generic
to work with multiple reg location and bitfield layout.
v2: Set/Clear XE2LPD_DDI_BUF_D2D_LINK_ENABLE in saved_port_bits when
enabling/disabling D2D so DDI_BUF_CTL is correctly programmed in
other places without overriding these bits (Clint)
v3: Leave saved_port_bits alone as those bits are not meant to be
modified outside of the port initialization. Rather propagate the
additional bit in DDI_BUF_CTL to be set when that register is
written again after D2D is enabled.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126224638.4132016-2-lucas.demarchi@intel.com
On HSW non-ULT (or at least on Dell Latitude E6540) external displays
start to flicker when we enable PSR on the eDP. We observe a much higher
SR and PC6 residency than should be possible with an external display,
and indeen much higher than what we observe with eDP disabled and
only the external display enabled. Looks like the hardware is somehow
ignoring the fact that the external display is active during PSR.
I wasn't able to redproduce this on my HSW ULT machine, or BDW.
So either there's something specific about this particular laptop
(eg. some unknown firmware thing) or the issue is limited to just
non-ULT HSW systems. All known registers that could affect this
look perfectly reasonable on the affected machine.
As a workaround let's unmask the LPSP event to prevent PSR entry
except while in LPSP mode (only pipe A + eDP active). This
will prevent PSR entry entirely when multiple pipes are active.
The one slight downside is that we now also prevent PSR entry
when driving eDP with pipe B or C, but I think that's a reasonable
tradeoff to avoid having to implement a more complex workaround.
Cc: stable@vger.kernel.org
Fixes: 783d8b8087 ("drm/i915/psr: Re-enable PSR1 on hsw/bdw")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10092
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118212131.31868-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
(cherry picked from commit 94501c3ca6)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Instead of waiting until the interrupt reaches GuC, we can grab a
forcewake while triggering the H2G interrupt. GEN11_GUC_HOST_INTERRUPT
is inside sgunit and is not affected by forcewakes. However, there
could be some delays when platform is entering/exiting some higher
level platform sleep states and a H2G is triggered. A forcewake
ensures those sleep states have been fully exited and further
processing occurs as expected. The hysteresis timers for C6 and
higher sleep states will ensure there is no unwanted race between the
wake and processing of the interrupts by GuC.
This will have an official WA soon so adding a FIXME in the comments.
v2: Make the new ranges watertight to address BAT failures and update
commit message (Matt R).
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119193513.221730-1-vinay.belgaumkar@intel.com
Currently icl_compute_tc_phy_dplls() assumes that the active
PLL will be the TC PLL (as opposed to the TBT PLL). The actual
PLL will be selected during the modeset enable sequence, but
we need to put *something* into the crtc_state->shared_dpll
already during compute_config().
The downside of assuming one PLL or the other is that we'll
fail to fastset if the assumption doesn't match what was in
use previously. So let's instead keep the same PLL that was
in use previously (assuming there was one). This should allow
fastset to work again when using TBT PLL, at least in the
steady state.
Now, assuming we want keep the same PLL may not be entirely
correct either. But we should be covered by the type-c link
reset handling which will force a full modeset by flagging
connectors_changed=true which means the resulting modeset
can't be converted into a fastset even if the full crtc state
looks identical.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118142436.25928-1-ville.syrjala@linux.intel.com
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
This reverts commit cfeff354f7.
A core design consideration with legacy cursor updates is that the
cursor must not touch any other plane, even if we were to force it
to take the slow path. That is the real reason why the cursor uses
a fixed ddb allocation, not because bspec says so.
Treating cursors as any other plane during ddb allocation
violates that, which means we can now pull other planes into
fully unsynced legacy cursor mailbox commits. That is
definitely not something we've ever considered when designing
the rest of the code. The noarm+arm register write split in
particular makes that dangerous as previous updates can get
disarmed pretty much at any random time, and not necessarily
in an order that is actually safe (eg. against ddb overlaps).
So if we were to do this then:
- someone needs to expend the appropriate amount of brain
cells thinking through all the tricky details
- we should do it for all skl+ platforms since all
of those have double buffered wm/ddb registers. The current
arbitrary mtl+ cutoff doesn't really make sense
For the moment just go back to the original behaviour where
the cursor's ddb alloation does not change outside of
modeset/fastset. As of now anything else isn't safe.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213102519.13500-10-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Our legacy cursor updates are actually mailbox updates.
Ie. the hardware latches things once per frame on start of
vblank, but we issue an number of updates per frame,
withough any attempt to synchronize against the vblank
in software. So in theory only the last update issued
during the frame will latch, and the previous ones are
discarded.
However this can lead to problems with maintaining the
ggtt/iommu mappings as we have no idea which updates
will actually latch.
The problem is exacerbated by the hardware's annoying disarming
behaviour; any non-arming register write will disarm an already
armed update, only to be rearmed later by the arming register
(CURBASE in case of cursors). If a disarming write happens
just before the start of vblank, and the arming write happens
after start of vblank we have effectively prevented the hardware
from latching anything. And if we manage to straddle multiple
sequential vblank starts in this manner we effectively prevent
the hardware from latching any new registers for an arbitrary
amount of time. This provides more time for the (potentially
still in use by the hardware) gtt/iommu mappings to be torn
down.
A partial solution, of course, is to use vblank evasion to
avoid the register writes from spreading on both sides of
the start of vblank.
I've previously highlighted this problem as a general issue
affecting mailbox updates. I even added some notes to the
{i9xx,skl}_crtc_planes_update_arm() to remind us that the noarm
and arm phases both need to pulled into the vblank evasion
critical section if we actually decided to implement mailbox
updates in general. But as I never impelemented the noarm+arm
split for cursors we don't have to worry about that for the
moment.
We've been lucky enough so far that this hasn't really caused
problems. One thing that does help is that Xorg generally
sticks to the same cursor BO. But igt seems pretty good at
hitting this on MTL now, so apparently we have to start
thinking about this.
v2: Wait for PSR exit to avoid the vblank evasion timeout (1ms)
tripping due to PSR exit latency (~5ms typically)
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240116204927.23499-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
There isn't really any reason to make the caller suffer through
checking the vblank evasion min/max scanlines. If we somehow
ended up with bogus values (which really shouldn't happen)
then just skip the actual vblank evasion loop but otherwise
plow ahead as normal.
The only "real" change is that we now get+put a vblank reference
even if the min/max values are bogus, previously we skipped
directly to the end.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213102519.13500-7-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
On HSW non-ULT (or at least on Dell Latitude E6540) external displays
start to flicker when we enable PSR on the eDP. We observe a much higher
SR and PC6 residency than should be possible with an external display,
and indeen much higher than what we observe with eDP disabled and
only the external display enabled. Looks like the hardware is somehow
ignoring the fact that the external display is active during PSR.
I wasn't able to redproduce this on my HSW ULT machine, or BDW.
So either there's something specific about this particular laptop
(eg. some unknown firmware thing) or the issue is limited to just
non-ULT HSW systems. All known registers that could affect this
look perfectly reasonable on the affected machine.
As a workaround let's unmask the LPSP event to prevent PSR entry
except while in LPSP mode (only pipe A + eDP active). This
will prevent PSR entry entirely when multiple pipes are active.
The one slight downside is that we now also prevent PSR entry
when driving eDP with pipe B or C, but I think that's a reasonable
tradeoff to avoid having to implement a more complex workaround.
Cc: stable@vger.kernel.org
Fixes: 783d8b8087 ("drm/i915/psr: Re-enable PSR1 on hsw/bdw")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10092
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118212131.31868-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
This reverts commit 88b065943c.
Lenovo 82TQ is unhappy if we do the display on sequence this
late. The display output shows severe corruption.
It's unclear if this is a failure on our part (perhaps
something to do with sending commands in LP mode after HS
/video mode transmission has been started? Though the backlight
on command at least seems to work) or simply that there are
some commands in the sequence that are needed to be done
earlier (eg. could be some DSC init stuff?). If the latter
then I don't think the current Windows code would work
either, but maybe this was originally tested with an older
driver, who knows.
Root causing this fully would likely require a lot of
experimentation which isn't really feasible without direct
access to the machine, so let's just accept failure and
go back to the original sequence.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240116210821.30194-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit dc524d0597)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Pull drm fixes from Dave Airlie:
"This is just a wrap up of fixes from the last few days. It has the
proper fix to the i915/xe collision, we can clean up what you did
later once rc1 lands.
Otherwise it's a few other i915, a v3d, rockchip and a nouveau fix to
make GSP load on some original Turing GPUs.
i915:
- Fixes for kernel-doc warnings enforced in linux-next
- Another build warning fix for string formatting of intel_wakeref_t
- Display fixes for DP DSC BPC and C20 PLL state verification
v3d:
- register readout fix
rockchip:
- two build warning fixes
nouveau:
- fix GSP loading on Turing with different nvdec configuration"
* tag 'drm-next-2024-01-15-1' of git://anongit.freedesktop.org/drm/drm:
nouveau/gsp: handle engines in runl without nonstall interrupts.
drm/i915/perf: reconcile Excess struct member kernel-doc warnings
drm/i915/guc: reconcile Excess struct member kernel-doc warnings
drm/i915/gt: reconcile Excess struct member kernel-doc warnings
drm/i915/gem: reconcile Excess struct member kernel-doc warnings
drm/i915/dp: Fix the max DSC bpc supported by source
drm/i915: don't make assumptions about intel_wakeref_t type
drm/i915/dp: Fix the PSR debugfs entries wrt. MST connectors
drm/i915/display: Fix C20 pll selection for state verification
drm/v3d: Fix support for register debugging on the RPi 4
drm/rockchip: vop2: Drop unused if_dclk_rate variable
drm/rockchip: vop2: Drop superfluous include
This reverts commit 88b065943c.
Lenovo 82TQ is unhappy if we do the display on sequence this
late. The display output shows severe corruption.
It's unclear if this is a failure on our part (perhaps
something to do with sending commands in LP mode after HS
/video mode transmission has been started? Though the backlight
on command at least seems to work) or simply that there are
some commands in the sequence that are needed to be done
earlier (eg. could be some DSC init stuff?). If the latter
then I don't think the current Windows code would work
either, but maybe this was originally tested with an older
driver, who knows.
Root causing this fully would likely require a lot of
experimentation which isn't really feasible without direct
access to the machine, so let's just accept failure and
go back to the original sequence.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10071
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240116210821.30194-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Pull pwm updates from Thierry Reding:
"This contains a bunch of cleanups and simplifications across the
board, as well as a number of small fixes.
Perhaps the most notable change here is the addition of an API that
allows PWMs to be used in atomic contexts, which is useful when time-
critical operations are involved, such as using a PWM to generate IR
signals.
Finally, I have decided to step down as PWM subsystem maintainer. Due
to other responsibilities I have lately not been able to find the time
that the subsystem deserves and Uwe, who has been helping out a lot
for the past few years and has many things planned for the future, has
kindly volunteered to take over. I have no doubt that he will be a
suitable replacement"
* tag 'pwm/for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
MAINTAINERS: pwm: Thierry steps down, Uwe takes over
pwm: linux/pwm.h: fix Excess kernel-doc description warning
pwm: Add pwm_apply_state() compatibility stub
pwm: cros-ec: Drop documentation for dropped struct member
pwm: Drop two unused API functions
pwm: lpc18xx-sct: Don't modify the cached period of other PWM outputs
pwm: meson: Simplify using dev_err_probe()
pwm: stmpe: Silence duplicate error messages
pwm: Reduce number of pointer dereferences in pwm_device_request()
pwm: crc: Use consistent variable naming for driver data
pwm: omap-dmtimer: Drop locking
dt-bindings: pwm: ti,pwm-omap-dmtimer: Update binding for yaml
media: pwm-ir-tx: Trigger edges from hrtimer interrupt context
pwm: bcm2835: Allow PWM driver to be used in atomic context
pwm: Make it possible to apply PWM changes in atomic context
pwm: renesas: Remove unused include
pwm: Replace ENOTSUPP with EOPNOTSUPP
pwm: Rename pwm_apply_state() to pwm_apply_might_sleep()
pwm: Stop referencing pwm->chip
pwm: Update kernel doc for struct pwm_chip
...
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
Pull header cleanups from Kent Overstreet:
"The goal is to get sched.h down to a type only header, so the main
thing happening in this patchset is splitting out various _types.h
headers and dependency fixups, as well as moving some things out of
sched.h to better locations.
This is prep work for the memory allocation profiling patchset which
adds new sched.h interdepencencies"
* tag 'header_cleanup-2024-01-10' of https://evilpiepirate.org/git/bcachefs: (51 commits)
Kill sched.h dependency on rcupdate.h
kill unnecessary thread_info.h include
Kill unnecessary kernel.h include
preempt.h: Kill dependency on list.h
rseq: Split out rseq.h from sched.h
LoongArch: signal.c: add header file to fix build error
restart_block: Trim includes
lockdep: move held_lock to lockdep_types.h
sem: Split out sem_types.h
uidgid: Split out uidgid_types.h
seccomp: Split out seccomp_types.h
refcount: Split out refcount_types.h
uapi/linux/resource.h: fix include
x86/signal: kill dependency on time.h
syscall_user_dispatch.h: split out *_types.h
mm_types_task.h: Trim dependencies
Split out irqflags_types.h
ipc: Kill bogus dependency on spinlock.h
shm: Slim down dependencies
workqueue: Split out workqueue_types.h
...
Currently if rc6 is supported, it gets enabled and the sysfs files for
rc6_enable_show and rc6_enable_dev_show uses masks to check information
from drm_i915_private.
However rc6_support functions take more variables and conditions into
consideration and thus these masks are not enough for most of the modern
hardware and it is simpley lyting to the user.
Let's fix it by at least use the rc6.supported flag from intel_gt
information.
Signed-off-by: Juan Escamilla <jcescami@wasd.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240110010302.553597-1-jcescami@wasd.net
Document nested struct members with full names as described in
Documentation/doc-guide/kernel-doc.rst.
intel_guc.h:305: warning: Excess struct member 'lock' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'guc_ids' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'num_guc_ids' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'guc_ids_bitmap' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'guc_id_list' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'guc_ids_in_use' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'destroyed_contexts' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'destroyed_worker' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'reset_fail_worker' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'reset_fail_mask' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'sched_disable_delay_ms' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'sched_disable_gucid_threshold' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'lock' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'gt_stamp' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'ping_delay' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'work' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'shift' description in 'intel_guc'
intel_guc.h:305: warning: Excess struct member 'last_stat_jiffies' description in 'intel_guc'
18 warnings as Errors
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231226195432.10891-3-rdunlap@infradead.org
(cherry picked from commit e4cf1a70fa)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
