Instead of retrieving the backlight brightness in struct
backlight_properties manually, and then checking whether the backlight
should be on at all, use backlight_get_brightness() which does all
this and insulates this from future changes.
Instead of manually checking the power state in struct
backlight_properties, use backlight_is_blank().
While we're at it, drop .fb_blank from the initialisation function; it
is deprecated, and this helps make progress towards enabling its
removal. This change makes no functional difference since
FB_BLANK_UNBLANK is the default value.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220616172316.1355133-4-steve@sk2.org
The probe routine acquires the reset GPIO using GPIOD_OUT_LOW. Directly
afterwards it calls acx565akm_detect(), which sets the GPIO value to
HIGH. If the bootloader initialized the GPIO to HIGH before the probe
routine was called, there is only a very short time period of a few
instructions where the reset signal is LOW. Exact time depends on
compiler optimizations, kernel configuration and alignment of the stars,
but I expect it to be always way less than 10us. There are no public
datasheets for the panel, but acx565akm_power_on() has a comment with
timings and reset period should be at least 10us. So this potentially
brings the panel into a half-reset state.
The result is, that panel may not work after boot and can get into a
working state by re-enabling it (e.g. by blanking + unblanking), since
that does a clean reset cycle. This bug has recently been hit by Ivaylo
Dimitrov, but there are some older reports which are probably the same
bug. At least Tony Lindgren, Peter Ujfalusi and Jarkko Nikula have
experienced it in 2017 describing the blank/unblank procedure as
possible workaround.
Note, that the bug really goes back in time. It has originally been
introduced in the predecessor of the omapfb driver in commit 3c45d05be3
("OMAPDSS: acx565akm panel: handle gpios in panel driver") in 2012.
That driver eventually got replaced by a newer one, which had the bug
from the beginning in commit 84192742d9 ("OMAPDSS: Add Sony ACX565AKM
panel driver") and still exists in fbdev world. That driver has later
been copied to omapdrm and then was used as a basis for this driver.
Last but not least the omapdrm specific driver has been removed in
commit 45f16c82db ("drm/omap: displays: Remove unused panel drivers").
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 1c8fc3f0c5 ("drm/panel: Add driver for the Sony ACX565AKM panel")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127200429.129868-1-sebastian.reichel@collabora.com
Thierry needs fd70c7755b ("drm/bridge: tc358767: fix max_tu_symbol
value") to be able to merge his dp_link patch series.
Some adjacent changes conflicts, plus some clashes in i915 due to
cherry-picking and git trying to be helpful and leaving both versions
in.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a type field to the drm_panel structure to report the panel type,
using DRM_MODE_CONNECTOR_* macros (the values that make sense are LVDS,
eDP, DSI and DPI). This will be used to initialise the corresponding
connector type.
Update all panel drivers accordingly. The panel-simple driver only
specifies the type for the known to be LVDS panels, while all other
panels are left as unknown and will be converted on a case-by-case
basis as they all need to be carefully reviewed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-2-laurent.pinchart@ideasonboard.com
Instead of requiring all drivers to set the dev and funcs fields of
drm_panel manually after calling drm_panel_init(), pass the data as
arguments to the function. This simplifies the panel drivers, and will
help future refactoring when adding new arguments to drm_panel_init().
The panel drivers have been updated with the following Coccinelle
semantic patch, with manual inspection to verify that no call to
drm_panel_init() with a single argument still exists.
@@
expression panel;
expression device;
identifier ops;
@@
drm_panel_init(&panel
+ , device, &ops
);
...
(
-panel.dev = device;
-panel.funcs = &ops;
|
-panel.funcs = &ops;
-panel.dev = device;
)
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823193245.23876-3-laurent.pinchart@ideasonboard.com
