Ideally the busyness worker should take a gt pm wakeref because the
worker only needs to be active while gt is awake. However, the gt_park
path cancels the worker synchronously and this complicates the flow if
the worker is also running at the same time. The cancel waits for the
worker and when the worker releases the wakeref, that would call gt_park
and would lead to a deadlock.
The resolution is to take the global pm wakeref if runtime pm is already
active. If not, we don't need to update the busyness stats as the stats
would already be updated when the gt was parked.
Note:
- We do not requeue the worker if we cannot take a reference to runtime
pm since intel_guc_busyness_unpark would requeue the worker in the
resume path.
- If the gt was parked longer than time taken for GT timestamp to roll
over, we ignore those rollovers since we don't care about tracking the
exact GT time. We only care about roll overs when the gt is active and
running workloads.
- There is a window of time between gt_park and runtime suspend, where
the worker may run. This is acceptable since the worker will not find
any new data to update busyness.
v2: (Daniele)
- Edit commit message and code comment
- Use runtime pm in the worker
- Put runtime pm after enabling the worker
- Use Link tag and add Fixes tag
v3: (Daniele)
- Reword commit and comments and add details
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/7077
Fixes: 77cdd054dd ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230925192117.2497058-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit e2f99b79d4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Ideally the busyness worker should take a gt pm wakeref because the
worker only needs to be active while gt is awake. However, the gt_park
path cancels the worker synchronously and this complicates the flow if
the worker is also running at the same time. The cancel waits for the
worker and when the worker releases the wakeref, that would call gt_park
and would lead to a deadlock.
The resolution is to take the global pm wakeref if runtime pm is already
active. If not, we don't need to update the busyness stats as the stats
would already be updated when the gt was parked.
Note:
- We do not requeue the worker if we cannot take a reference to runtime
pm since intel_guc_busyness_unpark would requeue the worker in the
resume path.
- If the gt was parked longer than time taken for GT timestamp to roll
over, we ignore those rollovers since we don't care about tracking the
exact GT time. We only care about roll overs when the gt is active and
running workloads.
- There is a window of time between gt_park and runtime suspend, where
the worker may run. This is acceptable since the worker will not find
any new data to update busyness.
v2: (Daniele)
- Edit commit message and code comment
- Use runtime pm in the worker
- Put runtime pm after enabling the worker
- Use Link tag and add Fixes tag
v3: (Daniele)
- Reword commit and comments and add details
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/7077
Fixes: 77cdd054dd ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230925192117.2497058-1-umesh.nerlige.ramappa@intel.com
There is no reason to add gtt_offset to the cached head/tail pointers
stream->oa_buffer.head and stream->oa_buffer.tail. This causes the code to
constantly add gtt_offset and subtract gtt_offset and is error
prone.
It is much simpler to maintain stream->oa_buffer.head and
stream->oa_buffer.tail without adding gtt_offset to them and just allow for
the gtt_offset when reading/writing from/to HW registers.
v2: Minor tweak to commit message due to dropping patch in previous series
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920040211.2351279-1-ashutosh.dixit@intel.com
Rename struct drm_gpuva_manager to struct drm_gpuvm including
corresponding functions. This way the GPUVA manager's structures align
very well with the documentation of VM_BIND [1] and VM_BIND locking [2].
It also provides a better foundation for the naming of data structures
and functions introduced for implementing a common dma-resv per GPU-VM
including tracking of external and evicted objects in subsequent
patches.
[1] Documentation/gpu/drm-vm-bind-async.rst
[2] Documentation/gpu/drm-vm-bind-locking.rst
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920144343.64830-2-dakr@redhat.com
Starting with Xe_LP+, GFX_MSTR_IRQ contains status bits that have W1C
behavior. If we do not properly reset them, we would miss delivery of
interrupts if a pending bit is set when enabling IRQs.
As an example, the display part of our probe routine contains paths
where we wait for vblank interrupts. If a display interrupt was already
pending when enabling IRQs, we would time out waiting for the vblank.
Avoid the potential issue by clearing GFX_MSTR_IRQ as part of the IRQ
reset.
v2:
- Move logic from gen11_gt_irq_reset() to dg1_irq_reset(). (Matt)
BSpec: 50875, 54028
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920195351.59421-2-gustavo.sousa@intel.com
Multiple power domains need to be handled explicitly in each driver. The
driver core can not handle it automatically since it is not aware of
power sequencing requirements the hardware might have. This is not a
problem for simpledrm since everything is expected to be powered on by
the bootloader. simpledrm has just ensure it remains powered on during
its lifetime.
This is required on Apple silicon M2 and M2 Pro/Max/Ultra desktop
systems. The HDMI output initialized by the bootloader requires keeping
the display controller and a DP phy power domain on.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230912-simpledrm-multiple-power-domains-v2-1-01b66bfb1980@jannau.net
The driver uses a naming convention where functions for struct drm_*_funcs
callbacks are named ssd130x_$object_$operation, while the callbacks for
struct drm_*_helper_funcs are named ssd130x_$object_helper_$operation.
The idea is that this helper_ prefix in the function names denote that are
for struct drm_*_helper_funcs callbacks. This convention was copied from
other drivers when ssd130x was written, but Maxime pointed out that is the
exception rather than the norm.
So let's get rid of the _helper prefixes from the function handlers names.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230914195138.1518065-1-javierm@redhat.com
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
We have the same h/vsync_end vs. h/vtotal quirk in the VBT parser
that was also present in EDID parser. Adjust the VBT parser the
same way as was done for hte EDID parser to fixup h/vsync_end
instead of h/vtotal. While I'm not currently aware of any machines
that need this for the VBT it seems prudent to keep both parsers
in sync.
And while at it let's add some debugs here as well. A bit
lackluster but didn't feel like plumbing the connector all
the way down at this time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920211934.14920-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
There are some weird EDIDs floating around that have the sync
pulse extending beyond the end of the blanking period.
On the currently problemtic machine (HP Omni 120) EDID reports
the following mode:
"1600x900": 60 108000 1600 1780 1860 1800 900 910 913 1000 0x40 0x5
which is then "corrected" to have htotal=1861 by the current drm_edid.c
code.
The fixup code was originally added in commit 7064fef563 ("drm: work
around EDIDs with bad htotal/vtotal values"). Googling around we end up in
https://bugs.launchpad.net/ubuntu/hardy/+source/xserver-xorg-video-intel/+bug/297245
where we find an EDID for a Dell Studio 15, which reports:
(II) VESA(0): clock: 65.0 MHz Image Size: 331 x 207 mm
(II) VESA(0): h_active: 1280 h_sync: 1328 h_sync_end 1360 h_blank_end 1337 h_border: 0
(II) VESA(0): v_active: 800 v_sync: 803 v_sync_end 809 v_blanking: 810 v_border: 0
Note that if we use the hblank size (as opposed of the hsync_end)
from the DTD to determine htotal we get exactly 60Hz refresh rate in
both cases, whereas using hsync_end to determine htotal we get a
slightly lower refresh rates. This makes me believe the using the
hblank size is what was intended even in those cases.
Also note that in case of the HP Onmi 120 the VBIOS boots with these:
crtc timings: 108000 1600 1780 1860 1800 900 910 913 1000, type: 0x40 flags: 0x5
ie. it just blindly stuffs the bogus hsync_end and htotal from the DTD
into the transcoder timing registers, and the display works. I believe
the (at least more modern) hardware will automagically terminate the hsync
pulse when the timing generator reaches htotal, which again points that we
should use the hblank size to determine htotal. Unfortunatley the old bug
reports for the Dell machines are extremely lacking in useful details so
we have no idea what kind of timings the VBIOS programmed into the
hardware :(
Let's just flip this quirk around and reduce the length of the sync
pulse instead of extending the blanking period. This at least seems
to be the correct thing to do on more modern hardware. And if any
issues crop up on older hardware we need to debug them properly.
v2: Add debug message breadcrumbs (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8895
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920211934.14920-1-ville.syrjala@linux.intel.com
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver unbind time. Among other things, this means that if a
panel is in use that it won't be cleanly powered off at system
shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
I have attempted to put this in the right place at unbind time. In
most other DRM drivers the call is made right after the call to
drm_kms_helper_poll_fini(), so I've put it there. That means that this
call will also be made in the case that we hit errors in bind, since
kirin_drm_kms_cleanup() is called both in the bind error path and in
unbind. I believe this is harmless even though it's not needed in the
bind error path.
For handling shutdown, we rely on the common technique of seeing if
the drvdata is NULL to know whether we need to call
drm_atomic_helper_shutdown(). This makes it important to make sure
that the drvdata is NULL if bind failed or if unbind was called. We
don't need the actual check for NULL and we'll rely on the patch
("drm/atomic-helper: drm_atomic_helper_shutdown(NULL) should be a
noop").
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.6.I21e0916bbd276033f7d31979c0da171458dedd4d@changeid
Based on grepping through the source code these drivers appear to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver remove (or unbind) time. Among other things, this means
that if a panel is in use that it won't be cleanly powered off at
system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
A few notes about these fixes:
- I confirmed that these drivers were all DRIVER_MODESET type drivers,
which I believe makes this relevant.
- I confirmed that these drivers were all DRIVER_ATOMIC.
- When adding drm_atomic_helper_shutdown() to the remove/unbind path,
I added it after drm_kms_helper_poll_fini() when the driver had
it. This seemed to be what other drivers did. If
drm_kms_helper_poll_fini() wasn't there I added it straight after
drm_dev_unregister().
- This patch deals with drivers using the component model in similar
ways as the patch ("drm: Call drm_atomic_helper_shutdown() at
shutdown time for misc drivers")
- These fixes rely on the patch ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop") to simplify
shutdown.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> # tilcdc
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.5.I771eb4bd03d8772b19e7dcfaef3e2c167bce5846@changeid
Based on grepping through the source code these drivers appear to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.3.I10dbe099fb1059d304ba847d19fc45054f7ffe9f@changeid
Based on grepping through the source code these drivers appear to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
All of the drivers in this patch were fairly straightforward to fix
since they already had a call to drm_atomic_helper_shutdown() at
remove/unbind time but were just lacking one at system shutdown. The
only hitch is that some of these drivers use the component model to
register/unregister their DRM devices. The shutdown callback is part
of the original device. The typical solution here, based on how other
DRM drivers do this, is to keep track of whether the device is bound
based on drvdata. In most cases the drvdata is the drm_device, so we
can just make sure it is NULL when the device is not bound. In some
drivers, this required minor code changes. To make things simpler,
drm_atomic_helper_shutdown() has been modified to consider a NULL
drm_device as a noop in the patch ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop").
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.2.I9115e5d094a43e687978b0699cc1fe9f2a3452ea@changeid
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
This driver was fairly easy to update. The drm_device is stored in the
drvdata so we just have to make sure the drvdata is NULL whenever the
device is not bound. To make things simpler,
drm_atomic_helper_shutdown() has been modified to consider a NULL
drm_device as a noop in the patch ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop").
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901164111.RFT.1.I3d5598bd73a59b5ded71430736c93f67dc5dea61@changeid
Introduce correspondent definitions for choosing between CD2X CDCLK
and PLL CDCLK as a source. All the entries in cdclk table for xe2lpd are
defined with PLL CDCLK as source, so simply set it. Also
skl_cdclk_decimal() shouldn't be set in CDCLK_CTL anymore, so skip it
for display version 20 and above.
v2:
- Remove unneeded comment and use REG_BIT() (Matt Roper)
- Rename CDCLK_SOURCE_SEL_CDCLK_PLL() to MDCLK_SOURCE_SEL_CDCLK_PLL
to match spec (Lucas)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230919192128.2045154-22-lucas.demarchi@intel.com
Add a new CDCLK table for Lunar Lake.
v2:
- Remove mdclk from the table as it's not needed (Matt Roper)
- Update waveform values to the latest from spec (Matt Roper)
- Rename functions and calculation to match by pixel rate (Lucas)
v3: Keep only the table: as far as intel_pixel_rate_to_cdclk()
is concerned, the minimum cdclk should still be half the pixel
rate on Xe2 (bspec 68858:
"Pipe maximum pixel rate = 2 * CDCLK frequency * Pipe Ratio")
(Matt Roper)
Bspec: 68861, 68858
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230919192128.2045154-19-lucas.demarchi@intel.com
