The refresh reported by modetest is 60.46Hz, and the actual measurement
is 60.01Hz, which is outside the expected tolerance. Adjust hporch and
pixel clock to fix it. After repair, modetest and actual measurement were
all 60.01Hz.
Modetest refresh = Pixel CLK/ htotal* vtotal, but measurement frame rate
is HS->LP cycle time(Vblanking). Measured frame rate is not only affecte
by Htotal/Vtotal/pixel clock, also affected by Lane-num/PixelBit/LineTime
/DSI CLK. Assume that the DSI controller could not make the mode that we
requested(presumably it's PLL couldn't generate the exact pixel clock?).
If you use a different DSI controller, you may need to readjust these
parameters. Now this panel looks like it's only used by me on the MTK
platform, so let's change this set of parameters.
Fixes: 1bc2ef065f ("drm/panel: Support for Starry-himax83102-j02 TDDI MIPI-DSI panel")
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120020109.3216343-1-yangcong5@huaqin.corp-partner.google.com
Atm the allocated MST PBN value is calculated from the TU size (number
of allocated MTP slots) as
PBN = TU * pbn_div
pbn_div being the link BW for each MTP slot. For DP 1.4 link rates this
worked, as pbn_div there is guraranteed to be an integer number, however
on UHBR this isn't the case. To get a PBN, TU pair where TU is a
properly rounded-up value covering all the BW corresponding to PBN,
calculate first PBN and from PBN the TU value.
Calculate PBN directly from the effective pixel data rate, instead of
calculating it indirectly from the corresponding TU and pbn_div values
(which are in turn derived from the pixel data rate and BW overhead).
Add a helper function to calculate the effective data rate, also adding
a note that callers of intel_dp_link_required() may also need to check
the effective data rate (vs. the data rate w/o the BW overhead).
While at it add a note to check if WA#14013163432 is applicable.
v2:
- Fix PBN calculation, deriving it from the effective data rate directly
instead of using the indirect TU and pbn_div values for this.
- Add a note about WA#14013163432. (Arun)
v3:
- Fix rounding up quotient while calculating remote_tu. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117150929.1767227-3-imre.deak@intel.com
The next patch will calculate the PBN value directly from the pixel data
rate and the BW allocation overhead, not requiring the data, link M/N
and TU values for this. To prepare for that move the calculation of BW
overheads from intel_dp_mst_compute_m_n() to
intel_dp_mst_find_vcpi_slots_for_bpp().
While at it store link_bpp in a .4 fixed point format.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-8-imre.deak@intel.com
The link M/N ratio is the data rate / link symbol clock rate, fix things
up accordingly. On DP 1.4 this ratio was correct as the link symbol clock
rate in that case matched the link data rate (in bytes/sec units, the
symbol size being 8 bits), however it wasn't correct for UHBR rates
where the symbol size is 32 bits.
Kudos to Arun noticing in Bspec the incorrect use of link data rate in
the ratio's N value.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-7-imre.deak@intel.com
Since the edid_firmware module parameter was moved from
drm_kms_helper.ko to drm.ko in v4.15, we've had a backwards
compatibility helper in place, with a DRM_NOTE() suggesting to migrate
to drm.edid_firmware. This was added in commit ac6c35a4d8 ("drm: add
backwards compatibility support for drm_kms_helper.edid_firmware").
More than five years and 30+ kernel releases later, drop the backward
compatibility.
v2: Drop the warnings too
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114151406.61230-1-jani.nikula@intel.com
Many user-space compositors fail with mode setting if a CRTC has
more than one connected connector. This is the case with the BMC
on Aspeed systems. Work around this problem by setting the BMC's
connector status to disconnected when the physical connector has
a display attached. This way compositors will only see one connected
connector at a time; either the physical one or the BMC.
Suggested-by: Jocelyn Falempe <jfalempe@redhat.com>
Fixes: e329cb53b4 ("drm/ast: Add BMC virtual connector")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116130217.22931-1-tzimmermann@suse.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the sprd drm drivers from always returning zero in the
remove callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-33-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-32-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-31-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-30-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-29-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-28-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-27-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the etnaviv drm driver from always returning zero in
the remove callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-25-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-24-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-23-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the armada drm drivers from always returning zero in
the remove callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-21-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-20-u.kleine-koenig@pengutronix.de
Error messages resulting from incorrect usage of the kernel uabi should
not spam dmesg by default. But it is useful to enable them to debug
userspace. So demote to DRM_UT_DRIVER.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/564189/
The EXT_external_objects extension is a bit awkward as it doesn't pass
explicit modifiers, leaving the importer to guess with incomplete
information. In the case of vk (turnip) exporting and gl (freedreno)
importing, the "OPTIMAL_TILING_EXT" layout depends on VkImageCreateInfo
flags (among other things), which the importer does not know. Which
unfortunately leaves us with the need for a metadata back-channel.
The contents of the metadata are defined by userspace. The
EXT_external_objects extension is only required to work between
compatible versions of gl and vk drivers, as defined by device and
driver UUIDs.
v2: add missing metadata kfree
v3: Rework to move copy_from/to_user out from under gem obj lock
to avoid angering lockdep about deadlocks against fs-reclaim
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/566157/
Until various PM devfreq/QoS and interconnect patches land, we could
potentially trigger reclaim from gpu scheduler thread, and under enough
memory pressure that could trigger a sort of deadlock. Eventually the
wait will timeout and we'll move on to consider other GEM objects. But
given that there is still a potential for deadlock/stalling, we should
reduce the timeout to contain the damage.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/568031/
Fix a sparse warning with this message
"warning:dereference of noderef expression". In this context it means we
are dereferencing a __rcu tagged pointer directly.
We should not be directly dereferencing a rcu pointer. To get a normal
(non __rcu tagged pointer) from a __rcu tagged pointer we are using the
function unrcu_pointer(...). The non __rcu tagged pointer then can be
dereferenced just like a normal pointer.
I tested with qemu with this command
qemu-system-x86_64 \
-m 2G \
-smp 2 \
-kernel bzImage \
-append "console=ttyS0 root=/dev/sda earlyprintk=serial net.ifnames=0" \
-drive file=bullseye.img,format=raw \
-net user,host=10.0.2.10,hostfwd=tcp:127.0.0.1:10021-:22 \
-net nic,model=e1000 \
-enable-kvm \
-nographic \
-pidfile vm.pid \
2>&1 | tee vm.log
with lockdep enabled.
Fixes: 0ec5f02f0e ("drm/nouveau: prevent stale fence->channel pointers, and protect with rcu")
Signed-off-by: Abhinav Singh <singhabhinav9051571833@gmail.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113191303.3277733-1-singhabhinav9051571833@gmail.com
