Add a 200ms delay after sending a ctrl report to Quadro,
Octo, D5 Next and Aquaero to give them enough time to
process the request and save the data to memory. Otherwise,
under heavier userspace loads where multiple sysfs entries
are usually set in quick succession, a new ctrl report could
be requested from the device while it's still processing the
previous one and fail with -EPIPE. The delay is only applied
if two ctrl report operations are near each other in time.
Reported by a user on Github [1] and tested by both of us.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/82
Fixes: 752b927951 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230807172004.456968-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 662d20b3a5 ("hwmon: (aquacomputer_d5next) Add support for
temperature sensor offsets") changed aqc_get_ctrl_val() to return
the value through a parameter instead of through the return value,
but didn't fix up a case that relied on the old behavior. Fix it
to use the proper received value and not the return code.
Fixes: 662d20b3a5 ("hwmon: (aquacomputer_d5next) Add support for temperature sensor offsets")
Cc: stable@vger.kernel.org
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230714120712.16721-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Leakshield leak prevention system, which communicates
through a proprietary USB HID protocol. Implemented by Noah Bergbauer [1].
Two temperature sensors are exposed, along with pressure (current, min, max
and target), reservoir volume (total and filled), pump speed and flow. Pump
speed and flow values are user provided and allow the Leakshield to
optimize its operation. Writing them to the device is subject of future
patches.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/41
Originally-from: Noah Bergbauer <main@ehvag.de>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230520095447.509287-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the option to control fan PWM on Aquacomputer Aquaero. The Aquaero is
the most complex Aquacomputer device, control is therefore more complicated
then on already supported devices.
Setting PWM requires multiple steps. First, an internal static PWM
controller is set to the desired PWM value. Second, the fan is set to use
that PWM controller. Last, the minimum and maximum accepted PWM values
of the fan are set to allow all possible PWM values.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-7-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Aquastream Ultimate watercooling pump, which communicates
through a proprietary USB HID protocol.
Coolant temp and external temp sensor readings are available, along with
speed, power, voltage and current of both the pump and optionally connected
fan. It also exposes pressure and flow speed readings.
Additionally, serial number and firmware version are exposed through
debugfs.
Tested by a user on Github [1].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/50
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230203120324.579808-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorganize macro definitions into sections for each supported
device, with additional comments on their purpose. This should
make it easier to follow what report each offset is coming
from. Also, reformat per-device initializations in
aqc_probe() to organize them into sections (fan info,
temp sensors, other parameters and lastly labels).
No functional changes.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20221107142455.655998-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading virtual temperature sensors for the D5 Next, Octo,
Quadro and Farbwerk 360.
Virtual temperature sensors are written to the device by the user, pulling
from an arbitrary value source. Writing to them is not yet reverse
engineered, so the only way to set them for now is to use the official
software.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220817121441.112198-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The offsets for setting speeds of fans connected to Quadro are off by one.
Set them to their correct values.
The offsets as shown point to registers for setting the fan control mode,
which will be explored in future patches, but slipped in here. When
setting fan speeds, the resulting values were overlapping, which made the
fans still run in my initial testing.
Fixes: cdbe34da01 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Quadro fan controller")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220914114327.6941-1-savicaleksa83@gmail.com
Cc: stable@vger.kenrel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As preparation for adding support for more devices in upcoming patches,
move device-specific data, such as number of fans, temperature sensors,
register offsets etc. to struct aqc_data. This is made possible by
the fact that the supported Aquacomputer devices share the same layouts
of sensor substructures. This allows aqc_raw_event() and others to stay
general and not be cluttered with similar loops for each device.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220707115050.90021-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware
temperature sensors of the Aquacomputer Farbwerk RGB controller, which
communicates through a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
Also, add Jack Doan to MAINTAINERS for this driver.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/YmTcrq8Gzel0zYYD@jackdesk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Octo fan controller, which communicates
through a proprietary USB HID protocol.
Four temperature sensors and eight PWM controllable fans are available.
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220404134212.9690-1-savicaleksa83@gmail.com
[groeck: Add missing "select CRC16"]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
of the Aquacomputer Farbwerk 360 RGB controller, which communicates through
a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
