Convert the driver to use the new IIO backend framework. The device
functionality is expected to be the same (meaning no added or removed
features).
Also note this patch effectively breaks ABI and that's needed so we can
properly support this device and add needed features making use of the
new IIO framework.
Given the lack of features (and devices supported) in the ad9467 driver
compared with the ADI out of tree version, we don't expect any user of
the upstream driver so no one should notice the ABI breakage. However,
if someone is affected by this, ADI will happily support transitioning
to the backend framework.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240210-iio-backend-v11-6-f5242a5fb42a@analog.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MAX34408/MAX34409 are two- and four-channel current monitors that are
configured and monitored with a standard I2C/SMBus serial interface. Each
unidirectional current sensor offers precision high-side operation with a
low full-scale sense voltage. The devices automatically sequence through
two or four channels and collect the current-sense samples and average them
to reduce the effect of impulse noise. The raw ADC samples are compared to
user-programmable digital thresholds to indicate overcurrent conditions.
Overcurrent conditions trigger a hardware output to provide an immediate
indication to shut down any necessary external circuitry.
Add as ADC driver which only supports current monitoring for now.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
Link: https://lore.kernel.org/r/20231014211254.16719-3-fr0st61te@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.
Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:
T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull Char/Misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem updates
for 6.5-rc1.
Lots of different, tiny, stuff in here, from a range of smaller driver
subsystems, including pulls from some substems directly:
- IIO driver updates and additions
- W1 driver updates and fixes (and a new maintainer!)
- FPGA driver updates and fixes
- Counter driver updates
- Extcon driver updates
- Interconnect driver updates
- Coresight driver updates
- mfd tree tag merge needed for other updates on top of that, lots of
small driver updates as patches, including:
- static const updates for class structures
- nvmem driver updates
- pcmcia driver fix
- lots of other small driver updates and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (243 commits)
bsr: fix build problem with bsr_class static cleanup
comedi: make all 'class' structures const
char: xillybus: make xillybus_class a static const structure
xilinx_hwicap: make icap_class a static const structure
virtio_console: make port class a static const structure
ppdev: make ppdev_class a static const structure
char: misc: make misc_class a static const structure
/dev/mem: make mem_class a static const structure
char: lp: make lp_class a static const structure
dsp56k: make dsp56k_class a static const structure
bsr: make bsr_class a static const structure
oradax: make 'cl' a static const structure
hwtracing: hisi_ptt: Fix potential sleep in atomic context
hwtracing: hisi_ptt: Advertise PERF_PMU_CAP_NO_EXCLUDE for PTT PMU
hwtracing: hisi_ptt: Export available filters through sysfs
hwtracing: hisi_ptt: Add support for dynamically updating the filter list
hwtracing: hisi_ptt: Factor out filter allocation and release operation
samples: pfsm: add CC_CAN_LINK dependency
misc: fastrpc: check return value of devm_kasprintf()
coresight: dummy: Update type of mode parameter in dummy_{sink,source}_enable()
...
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the large set of driver changes for char/misc drivers and
other smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem
seems under very active development recently. This required also
merging in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the
shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (223 commits)
scripts/tags.sh: fix incompatibility with PCRE2
firmware: coreboot: Remove GOOGLE_COREBOOT_TABLE_ACPI/OF Kconfig entries
mei: lower the log level for non-fatal failed messages
mei: bus: disallow driver match while dismantling device
misc: vmw_balloon: fix memory leak with using debugfs_lookup()
nvmem: stm32: fix OPTEE dependency
dt-bindings: nvmem: qfprom: add IPQ8074 compatible
nvmem: qcom-spmi-sdam: register at device init time
nvmem: rave-sp-eeprm: fix kernel-doc bad line warning
nvmem: stm32: detect bsec pta presence for STM32MP15x
nvmem: stm32: add OP-TEE support for STM32MP13x
nvmem: core: use nvmem_add_one_cell() in nvmem_add_cells_from_of()
nvmem: core: add nvmem_add_one_cell()
nvmem: core: drop the removal of the cells in nvmem_add_cells()
nvmem: core: move struct nvmem_cell_info to nvmem-provider.h
nvmem: core: add an index parameter to the cell
of: property: add #nvmem-cell-cells property
of: property: make #.*-cells optional for simple props
of: base: add of_parse_phandle_with_optional_args()
net: add helper eth_addr_add()
...
The TI LMP92064 is a dual 12 Bit ADC connected via SPI.
The two channels are intended for simultaneous measurements of the voltage
across- and current through a load to allow accurate instantaneous power
measurements.
The driver does not yet take advantage of this feature, as buffering is not
yet implemented.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Link: https://lore.kernel.org/r/20221128133503.1355898-2-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD4130-8 is an ultra-low power, high precision, measurement solution for
low bandwidth battery operated applications.
The fully integrated AFE (Analog Front-End) includes a multiplexer for up
to 16 single-ended or 8 differential inputs, PGA (Programmable Gain
Amplifier), 24-bit Sigma-Delta ADC, on-chip reference and oscillator,
selectable filter options, smart sequencer, sensor biasing and excitation
options, diagnostics, and a FIFO buffer.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20221021104115.1812486-3-demonsingur@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adding support for max11410 24-bit, 1.9ksps delta-sigma adc which
has 3 differential reference and 10 differential channel inputs.
Inputs and references can be buffered internally. Inputs can also
be amplified with internal PGA.
Device has four digital filter modes: FIR50/60, FIR50, FIR60 and SINC4.
FIR 50Hz and 60Hz rejections can be enabled/disabled separately.
Digital filter selection affects sampling frequency range so driver
has to consider the configured filter when configuring sampling frequency.
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Link: https://lore.kernel.org/r/20221003105903.229-2-Ibrahim.Tilki@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such
as temperature and supply voltage levels. The AMS has two SYSMON blocks.
PL-SYSMON block is capable of monitoring off chip voltage and
temperature.
PL-SYSMON block has DRP, JTAG and I2C interface to enable monitoring
from an external master. Out of these interfaces currently only DRP is
supported. Other block PS-SYSMON is memory mapped to PS.
The AMS can use internal channels to monitor voltage and temperature as
well as one primary and up to 16 auxiliary channels for measuring
external voltages.
The voltage and temperature monitoring channels also have event capability
which allows to generate an interrupt when their value falls below or
raises above a set threshold.
Co-developed-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Link: https://lore.kernel.org/r/20211203212358.31444-4-anand.ashok.dumbre@xilinx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We could probably drop a lot more of these, but for now this removes
unnecessary restrictions on stand alone ADC devices.
For these 3 drivers the false dependency seems to date all
the way back to their initial introduction.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Nothing in this driver depends on OF firmware so drop the dependency
and update the headers to remove the false impression such a dependency
exists.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Commit 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP
ADC") adds the config IMX8QXP_ADC for this new driver, which depends on
the non-existing config ARCH_MXC_ARM64.
Hence, ./scripts/checkkconfigsymbols.py warns:
ARCH_MXC_ARM64
Referencing files: drivers/iio/adc/Kconfig
Probably, the existing config ARCH_MXC is intended to be referred here.
So, repair the dependency to refer to that config.
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211111083954.6286-1-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Basically the TI TSC2046 touchscreen controller is 8 channel ADC optimized for
the touchscreen use case. By implementing it as an IIO ADC device, we can
make use of resistive-adc-touch and iio-hwmon drivers.
Polled readings are currently not implemented to keep this patch small, so
iio-hwmon will not work out of the box for now.
So far, this driver was tested with a custom version of resistive-adc-touch driver,
since it needs to be extended to make use of Z1 and Z2 channels. The X/Y
are working without additional changes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210428073208.19570-4-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Because a dependency on HAS_IOMEM and OF was added for the ADI AXI ADC
driver, this makes the AD9467 driver have some build/dependency issues
when OF is disabled (typically on ACPI archs like x86).
This is because the selection of the AD9467 enforces the ADI_AXI_ADC symbol
which is blocked by the OF (and potentially HAS_IOMEM) being disabled.
To fix this, we make the AD9467 driver depend on the ADI_AXI_ADC symbol.
The AD9467 driver cannot operate on it's own. It requires the ADI AXI ADC
driver to stream data (or some similar IIO interface).
So, the fix here is to make the AD9467 symbol depend on the ADI_AXI_ADC
symbol. At some point this could become it's own subgroup of high-speed
ADCs.
Fixes: be24c65e9f ("iio: adc: adi-axi-adc: add proper Kconfig dependencies")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210324182746.9337-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
