SCCC (SCC Context) is a context with QP granularity that contains
information about congestion control. Dump SCCC and QPC together
to improve troubleshooting.
When dumping raw QPC with rdmatool, there will be a total of 576 bytes
data output, where the first 512 bytes is QPC and the last 64 bytes is
SCCC. When congestion control is disabled, the 64 byte SCCC will be all 0.
Example:
$rdma res show qp -jpr
[ {
"ifindex": 0,
"ifname": "hns_0",
"data": [ 67,0,0,0... 512bytes
4,0,2... 64bytes]
},...
} ]
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240305055257.823513-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently, congestion control algorithm is statically configured in
FW, and all QPs use the same algorithm(except UD which has a fixed
configuration of DCQCN). This is not flexible enough.
Support userspace configuring congestion control algorithm with QP
granularity while creating QPs. If the algorithm is not specified in
userspace, use the default one.
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240301104845.1141083-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Commit 27c5fd271d ("RDMA/hns: The UD mode can only be configured
with DCQCN") adds a check of congest control alorithm for UD. But
that patch causes a problem: hr_dev->caps.congest_type is global,
used by all QPs, so modifying this field to DCQCN for UD QPs causes
other QPs unable to use any other algorithm except DCQCN.
Revert the modification in commit 27c5fd271d ("RDMA/hns: The UD
mode can only be configured with DCQCN"). Add a new field cong_type
to struct hns_roce_qp and configure DCQCN for UD QPs.
Fixes: 27c5fd271d ("RDMA/hns: The UD mode can only be configured with DCQCN")
Fixes: f91696f2f0 ("RDMA/hns: Support congestion control type selection according to the FW")
Signed-off-by: Luoyouming <luoyouming@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240219061805.668170-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
'struct hns_roce_hem' is used to refer to the last level of
dma buffer managed by the hw, pointed by a single BA(base
address) in the previous level of BT(base table), so the dma
buffer in 'struct hns_roce_hem' must be contiguous.
Right now the size of dma buffer in 'struct hns_roce_hem' is
decided by mhop->buf_chunk_size in get_hem_table_config(),
which ensure the mhop->buf_chunk_size is power of two of
PAGE_SIZE, so there will be only one contiguous dma buffer
allocated in hns_roce_alloc_hem(), which means hem->chunk_list
and chunk->mem for linking multi dma buffers is unnecessary.
This patch removes the hem->chunk_list and chunk->mem and other
related macro and function accordingly.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240113085935.2838701-7-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
IB-core and rdma-core restrict the sgid_index specified by users,
which is uint8_t/u8 data type, to only be within the range of 0-255,
so it's meaningless to support excessively large gid_table_len.
On the other hand, ib-core creates as many sysfs gid files as
gid_table_len, most of which are not only useless because of the
reason above, but also greatly increase the traversal time of
the sysfs gid files for applications.
This patch limits the maximum length of gid table to 256.
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20231207114231.2872104-4-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
During device init, a struct for HW stats will be allocated. As HW
stats are not supported for VF and HIP08, currently
hns_roce_alloc_hw_port_stats() returns NULL in this case. However,
ib-core considers the returned NULL pointer as memory allocation
failure and returns ENOMEM, eventually leading to the failure of VF
and HIP08 init.
In the case where the driver does not support the .alloc_hw_port_stats()
ops, ib-core will return EOPNOTSUPP and ignore this error code in the
upper layer function. So for VF and HIP08, just don't set the HW stats
ops to ib-core.
Fixes: 5a87279591 ("RDMA/hns: Support hns HW stats")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20231017125239.164455-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
ucmd in hns_roce_create_qp_common() are not initialized. But it works fine
until new member sdb_addr is added to struct hns_roce_ib_create_qp.
If the user-mode driver uses an old version ABI, then the value of the new
member will be undefined after ib_copy_from_udata().
This patch fixes it by initialize this variable to 0. And the default value
of the new member sdb_addr will be 0 which is invalid.
Fixes: 0425e3e6e0 ("RDMA/hns: Support flush cqe for hip08 in kernel space")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20231017125239.164455-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The current driver will print all asynchronous events. Some of the
print levels are set improperly, e.g. SRQ limit reach and SRQ last
wqe reach, which may also occur during normal operation of the software.
Currently, the information of these event is printed as a warning,
which causes a large amount of printing even during normal use of the
application. As a result, the service performance deteriorates.
This patch fixes the printing storms by modifying the print level.
Fixes: b00a92c8f2 ("RDMA/hns: Move all prints out of irq handle")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20231017125239.164455-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Compared with normal doorbell, using record doorbell can shorten the
process of ringing the doorbell and reduce the latency.
Add a flag HNS_ROCE_CAP_FLAG_SRQ_RECORD_DB to allow FW to
enable/disable SRQ record doorbell.
If the flag above is set, allocate the dma buffer for SRQ record
doorbell and write the buffer address into SRQC during SRQ creation.
For userspace SRQ, add a flag HNS_ROCE_RSP_SRQ_CAP_RECORD_DB to notify
userspace whether the SRQ record doorbell is enabled.
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20230926130026.583088-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently, direct wqe is not supported for wr-list. RoCE driver excludes
direct wqe for wr-list by judging whether the number of wr is 1.
For a wr-list where the second wr is a length-error atomic wr, the
post-send driver handles the first wr and adds 1 to the wr number counter
firstly. While handling the second wr, the driver finds out a length error
and terminates the wr handle process, remaining the counter at 1. This
causes the driver mistakenly judges there is only 1 wr and thus enters
the direct wqe process, carrying the current length-error atomic wqe.
This patch fixes the error by adding a judgement whether the current wr
is a bad wr. If so, use the normal doorbell process but not direct wqe
despite the wr number is 1.
Fixes: 01584a5edc ("RDMA/hns: Add support of direct wqe")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20230804012711.808069-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Long message loopback slice is used for achieving traffic balance between
QPs. It prevents the problem that QPs with large traffic occupying the
hardware pipeline for a long time and QPs with small traffic cannot be
scheduled.
Currently, its maximum value is set to 16K, which means only after a QP
sends 16K will the second QP be scheduled. This value is too large, which
will lead to unbalanced traffic scheduling, and thus it needs to be
modified.
The setting range of the long message loopback slice is modified to be
from 1024 (the lower limit supported by hardware) to mtu. Actual testing
shows that this value can significantly reduce error in hardware traffic
scheduling.
This solution is compatible with both HIP08 and HIP09. The modified
lp_pktn_ini has a maximum value of 2 (when mtu is 256), so the range
checking code for lp_pktn_ini is no longer necessary and needs to be
deleted.
Fixes: 0e60778efb ("RDMA/hns: Modify the value of MAX_LP_MSG_LEN to meet hardware compatibility")
Link: https://lore.kernel.org/r/20230512092245.344442-4-huangjunxian6@hisilicon.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
For hns, the specification of an entry like resource (E.g. WQE/CQE/EQE)
depends on BT page size, buf page size and hopnum. For user mode, the buf
page size depends on UMEM. Therefore, the actual specification is
controlled by BT page size and hopnum.
The current BT page size and hopnum are obtained from firmware. This makes
the driver inflexible and introduces unnecessary constraints. Resource
allocation failures occur in many scenarios.
This patch will calculate whether the BT page size set by firmware is
sufficient before allocating BT, and increase the BT page size if it is
insufficient.
Fixes: 1133401412 ("RDMA/hns: Optimize base address table config flow for qp buffer")
Link: https://lore.kernel.org/r/20230512092245.344442-3-huangjunxian6@hisilicon.com
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
On HIP08, the queried timeout attr is different from the timeout attr
configured by the user.
It is found by rdma-core testcase test_rdmacm_async_traffic:
======================================================================
FAIL: test_rdmacm_async_traffic (tests.test_rdmacm.CMTestCase)
----------------------------------------------------------------------
Traceback (most recent call last):
File "./tests/test_rdmacm.py", line 33, in test_rdmacm_async_traffic
self.two_nodes_rdmacm_traffic(CMAsyncConnection, self.rdmacm_traffic,
File "./tests/base.py", line 382, in two_nodes_rdmacm_traffic
raise(res)
AssertionError
Fixes: 926a01dc00 ("RDMA/hns: Add QP operations support for hip08 SoC")
Link: https://lore.kernel.org/r/20230512092245.344442-2-huangjunxian6@hisilicon.com
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
