.n_sectors is rarely used. In fact it is only used in swp.c and to
calculate the flash size in the core. The use in swp.c might be
converted to use the (largest) flash erase size. For now, we just
locally calculate the sector size.
Simplify the flash_info database and set the size of the flash directly.
This also let us use the SZ_x macros.
Verified that there's no flash that specifies BP and sector size of zero
to make sure we avoid a division by zero in
spi_nor_get_min_prot_length_sr(). We'll protect from a possible division
by zero in a further patch by introducing a default value for
sector_size.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-5-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Infineon S28Hx (SEMPER Octal) and S25FS256T (SEMPER Nano) support Clear
Program and Erase Failure Flags (CLPEF, 82h) instead of CLSR(30h).
Introduce a new mfr_flag together with the infrastructure to allow
manufacturer private data in the core. With this we remove the need
to have if checks in the code at runtime and instead set the correct
opcodes at probe time. S25Hx (SEMPER QSPI) supports CLSR but it may
be disabled by CFR3x[2] while CLPEF is always available. Therefore,
the mfr_flag is also applied to S25Hx for safety.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20230726075257.12985-2-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
SPI NOR chips are made of pages, which gathered in small groups make
(erase) sectors. Sectors, gathered together, make banks inside the
chip. Until now, there was only one bank per device supported, but we
are about to introduce support for new chips featuring several banks (up
to 4 so far) where different operations may happen in parallel.
Let's allow describing these additional bank parameters, and let's do
this independently of any other value (like the number of sectors) with
an absolute value.
By default we consider that all chips have a single bank.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20230328154105.448540-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Use NOR parameters in the probe's sequence of calls, thus
nor->params->size instead of nor->mtd.size and let the mtd_info
fields be used by the mtd calls (mtd->_erase, mtd->_read, mtd->_write).
mtd_info fields should not be used during probe because we haven't
registered mtd yet. It's safe to drop xilinx's setting of nor->mtd.size,
now that we use nor->params->size in spi_nor_set_addr_width().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-3-tudor.ambarus@microchip.com
As it was before the blamed commit, s3an_nor_scan() was called
after mtd size was set with params->size, and it overwrote the mtd
size value with '8 * nor->page_size * nor->info->n_sectors' when
XSR_PAGESIZE was set. With the introduction of
s3an_post_sfdp_fixups(), we missed to update the mtd size for the
s3an flashes. Fix the mtd size by updating both nor->params->size,
(which will update the mtd_info size later on) and nor->mtd.size
(which is used in spi_nor_set_addr_width()).
Fixes: 641edddb4f ("mtd: spi-nor: Add s3an_post_sfdp_fixups()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-2-tudor.ambarus@microchip.com
The SPI NOR controllers drivers must not be able to use structures that
are meant just for the SPI NOR core.
struct spi_nor_flash_parameter is filled at run-time with info gathered
from flash_info, manufacturer and sfdp data. struct spi_nor_flash_parameter
should be opaque to the SPI NOR controller drivers, make sure it is.
spi_nor_option_flags, spi_nor_read_command, spi_nor_pp_command,
spi_nor_read_command_index and spi_nor_pp_command_index are defined for the
core use, make sure they are opaque to the SPI NOR controller drivers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Create a SPI NOR manufacturer driver for Xilinx chips, and move the
Xilinx definitions outside of core.c.
While at it, remove the SPI_S3AN flag which is now useless.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
