The recent change to allow large frames without hardware checksumming
slotted in software checksumming in the driver if hardware could not
do it.
This will however upset TSO (TCP Segment Offloading). Typical
error dumps includes this:
skb len=2961 headroom=222 headlen=66 tailroom=0
(...)
WARNING: CPU: 0 PID: 956 at net/core/dev.c:3259 skb_warn_bad_offload+0x7c/0x108
gemini-ethernet-port: caps=(0x0000010000154813, 0x00002007ffdd7889)
And the packets do not go through.
The TSO implementation is bogus: a TSO enabled driver must propagate
the skb_shinfo(skb)->gso_size value to the TSO engine on the NIC.
Drop the size check and TSO offloading features for now: this
needs to be fixed up properly.
After this ethernet works fine on Gemini devices with a direct connected
PHY such as D-Link DNS-313.
Also tested to still be working with a DSA switch using the Gemini
ethernet as conduit interface.
Link: https://lore.kernel.org/netdev/CANn89iJLfxng1sYL5Zk0mknXpyYQPCp83m3KgD2KJ2_hKCpEUg@mail.gmail.com/
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: d4d0c5b4d2 ("net: ethernet: cortina: Handle large frames")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX max frame size is over 10000 for the Gemini ethernet,
but the TX max frame size is actually just 2047 (0x7ff after
checking the datasheet). Reflect this in what we offer to Linux,
cap the MTU at the TX max frame minus ethernet headers.
We delete the code disabling the hardware checksum for large
MTUs as netdev->mtu can no longer be larger than
netdev->max_mtu meaning the if()-clause in gmac_fix_features()
is never true.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-3-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Gemini ethernet controller provides hardware checksumming
for frames up to 1514 bytes including ethernet headers but not
FCS.
If we start sending bigger frames (after first bumping up the MTU
on both interfaces sending and receiving the frames), truncated
packets start to appear on the target such as in this tcpdump
resulting from ping -s 1474:
23:34:17.241983 14:d6:4d:a8:3c:4f (oui Unknown) > bc:ae:c5:6b:a8:3d (oui Unknown),
ethertype IPv4 (0x0800), length 1514: truncated-ip - 2 bytes missing!
(tos 0x0, ttl 64, id 32653, offset 0, flags [DF], proto ICMP (1), length 1502)
OpenWrt.lan > Fecusia: ICMP echo request, id 1672, seq 50, length 1482
If we bypass the hardware checksumming and provide a software
fallback, everything starts working fine up to the max TX MTU
of 2047 bytes, for example ping -s2000 192.168.1.2:
00:44:29.587598 bc:ae:c5:6b:a8:3d (oui Unknown) > 14:d6:4d:a8:3c:4f (oui Unknown),
ethertype IPv4 (0x0800), length 2042:
(tos 0x0, ttl 64, id 51828, offset 0, flags [none], proto ICMP (1), length 2028)
Fecusia > OpenWrt.lan: ICMP echo reply, id 1683, seq 4, length 2008
The bit enabling to bypass hardware checksum (or any of the
"TSS" bits) are undocumented in the hardware reference manual.
The entire hardware checksum unit appears undocumented. The
conclusion that we need to use the "bypass" bit was found by
trial-and-error.
Since no hardware checksum will happen, we slot in a software
checksum fallback.
Check for the condition where we need to compute checksum on the
skb with either hardware or software using == CHECKSUM_PARTIAL instead
of != CHECKSUM_NONE which is an incomplete check according to
<linux/skbuff.h>.
On the D-Link DIR-685 router this fixes a bug on the conduit
interface to the RTL8366RB DSA switch: as the switch needs to add
space for its tag it increases the MTU on the conduit interface
to 1504 and that means that when the router sends packages
of 1500 bytes these get an extra 4 bytes of DSA tag and the
transfer fails because of the erroneous hardware checksumming,
affecting such basic functionality as the LuCI web interface.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-2-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Drop the special defines in a bunch of drivers where the
removal is relatively simple so grouping into one patch
does not impact reviewability.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of drivers use eth_random_addr(netdev->dev_addr)
thus writing to netdev->dev_addr directly, and not setting
the address type. Switch them to eth_hw_addr_random().
@@
expression netdev;
@@
- eth_random_addr(netdev->dev_addr);
+ eth_hw_addr_random(netdev);
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
eth_hw_addr_set() takes a u8 pointer, like other
etherdevice helpers. Convert the few drivers which
require casts because they memcpy from "endian marked"
types.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cortina/gemini.c: In function gmac_get_ringparam:
drivers/net/ethernet/cortina/gemini.c:2125:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/cortina/gemini.c: In function gmac_init:
drivers/net/ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
these variable is never used, so remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's nice if the phy is online before we register the netdev
so try to do that first.
Stop trying to do "second tried" to register the phy, it
works perfectly fine the first time.
Stop remvoving the phy in uninit. Remove it when the
driver is remove():d, symmetric to where it is added, in
probe().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way,
when probe fails, netdev can be freed automatically.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the missing clk_disable_unprepare() before return
from gemini_ethernet_port_probe() in the error handling case.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of gmac_setup_txqs() the allocated desc_ring is
leaked if TX queue base is not aligned. Release it via
dma_free_coherent.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to free allocated netdev in remove like
what is done in probe failure.
Add the free to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header file related to ethernet driver for Cortina Gemini
devices. For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX stats should be started with the tx_stats_syncp,
there seems to be a copy/paste error in the driver.
Signed-off-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supposedly handles frames up to 10236 bytes and
implements .ndo_change_mtu() so accept 10236 minus the ethernet
header for a VLAN tagged frame on the netdevices. Use
ETH_MIN_MTU as minimum MTU.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initialization sequence for the ethernet, setting up
interrupt routing and such things, need to be done after
both the ports are clocked and reset. Before this the
config will not "take". Move the initialization to the
port probe function and keep track of init status in
the state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was not tested with two ports actually in use at
the same time. (I blame this on lack of actual hardware using
that feature.) Now after locating a system using both ports,
add necessary fix to make both ports come up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch over to using a module parameter and debug prints
that can be controlled by this or ethtool like everyone
else. Depromote all other prints to debug messages.
The phy_print_status() was already in place, albeit never
really used because the debuglevel hiding it had to be
set up using ethtool.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to calculate the hardware register enumerator
for the maximum L3 length isn't entirely simple to read.
Use the existing defines and rewrite the function into a
table look-up.
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in gemini dev_warn message
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
