GPIO EOI is not set to clear interrupt status after handling the
interrupt. It should be done in irq_chip->irq_ack, but this function
is not called in handle_nested_irq(). So executing function
txgbe_gpio_irq_ack() manually in txgbe_gpio_irq_handler().
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The register of GPIO interrupt status is masked before MAC IRQ
is enabled. This is because of hardware deficiency. So manually
clear the interrupt status before using them. Otherwise, GPIO
interrupts will never be reported again. There is a workaround for
clearing interrupts to set GPIO EOI in txgbe_up_complete().
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is a cleanup patch, making code a bit more concise.
1) Use skb_network_offset(skb) in place of
(skb_network_header(skb) - skb->data)
2) Use -skb_network_offset(skb) in place of
(skb->data - skb_network_header(skb))
3) Use skb_transport_offset(skb) in place of
(skb_transport_header(skb) - skb->data)
4) Use skb_inner_transport_offset(skb) in place of
(skb_inner_transport_header(skb) - skb->data)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com> # for sfc
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add a description to Wangxun's common code lib.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ngbe driver needs phylink:
arm-linux-gnueabi-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_nway_reset':
wx_ethtool.c:(.text+0x458): undefined reference to `phylink_ethtool_nway_reset'
arm-linux-gnueabi-ld: drivers/net/ethernet/wangxun/ngbe/ngbe_main.o: in function `ngbe_remove':
ngbe_main.c:(.text+0x7c): undefined reference to `phylink_destroy'
arm-linux-gnueabi-ld: drivers/net/ethernet/wangxun/ngbe/ngbe_main.o: in function `ngbe_open':
ngbe_main.c:(.text+0xf90): undefined reference to `phylink_connect_phy'
arm-linux-gnueabi-ld: drivers/net/ethernet/wangxun/ngbe/ngbe_mdio.o: in function `ngbe_mdio_init':
ngbe_mdio.c:(.text+0x314): undefined reference to `phylink_create'
Add the missing Kconfig description for this.
Fixes: bc2426d74a ("net: ngbe: convert phylib to phylink")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240111162828.68564-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to get RX/TX queue number with ethtool -l, and set RX/TX
queue number with ethtool -L. Since interrupts need to be rescheduled,
adjust the allocation of msix enties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support to show RX/TX coalesce with ethtool -c and set RX/TX
coalesce with ethtool -C.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support to query RX/TX depth with ethtool -g, and change RX/TX depth
with ethtool -G.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to set pause params with ethtool -A and get pause
params with ethtool -a, for ethernet driver txgbe and ngbe.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the following implementation, add struct phylink and phylink_config
to wx structure. Add the helper function for converting phylink to wx,
implement ethtool ksetting and nway reset in libwx.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifconfig ethx up, will set page->refcount larger than 1,
and then ifconfig ethx down, calling __page_frag_cache_drain()
to free pages, it is not compatible with page pool.
So deleting codes which changing page->refcount.
Fixes: 3c47e8ae11 ("net: libwx: Support to receive packets in NAPI")
Signed-off-by: duanqiangwen <duanqiangwen@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device uses a custom subsystem vendor ID, the function
wx_sw_init() returns before the memory of 'wx->mac_table' is allocated.
The null pointer will causes the kernel panic.
Fixes: 79625f45ca ("net: wangxun: Move MAC address handling to libwx")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers of mdio accessing are common defined in libwx, remove the
redundant macro definitions in ngbe driver.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wangxun SP chip supports to connect with external PHY (marvell 88x3310),
which links to 10GBASE-T/1000BASE-T/100BASE-T. Add the identification of
media types from subsystem device IDs. For sp_media_copper, register mdio
bus for the external PHY.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable data path before PCS VR reset while switching PCS mode, to prevent
the blocking of data path. Enable AN interrupt for CL37 auto-negotiation.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since XPCS device identifier is implemented in the firmware version
0x20010 and above, so add a warning to prompt the users to upgrade the
firmware to make sure the driver works.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core API pci_dev_id() can be used to get the BDF number for a pci
device. We don't need to compose it manually. Use pci_dev_id() to
simplify the code a little bit.
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old way to do LAN reset is sending reset command to firmware. Once
firmware performs reset, it reconfigures what it needs.
In the new firmware versions, veto bit is introduced for NCSI/LLDP to
block PHY domain in LAN reset. At this point, writing register of LAN
reset directly makes the same effect as the old way. And it does not
reset MNG domain, so that veto bit does not change.
Since veto bit was never used, the old firmware is compatible with the
driver before and after this change. The new firmware needs to use with
the driver after this change if it wants to implement the new feature,
otherwise it is the same as the old firmware.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230717021333.94181-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Identify issues that arise by using the tests/doublebitand.cocci
semantic patch. Need to remove duplicate expression in if statement.
Signed-off-by: Wang Ming <machel@vivo.com>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool_ops get_wol and set_wol.
Implement Wake-on-LAN support.
Wol requires hardware board support which use sub id
to identify.
Magic packets are checked by fw, for now just support
WAKE_MAGIC.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some device types like TXGBE_ID_XAUI, *checksum computed in
txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the
limit on the size of *checksum.
Fixes: 049fe53653 ("net: txgbe: Add operations to interact with firmware")
Fixes: 5e2ea7801f ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20230711063414.3311-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
txgbe_shutdown() relies on txgbe_dev_shutdown() to initialise
wake by passing it by reference. However, txgbe_dev_shutdown()
doesn't use this parameter at all.
wake is then passed uninitialised by txgbe_dev_shutdown()
to pci_wake_from_d3().
Resolve this problem by:
* Removing the unused parameter from txgbe_dev_shutdown()
* Removing the uninitialised variable wake from txgbe_dev_shutdown()
* Passing false to pci_wake_from_d3() - this assumes that
although uninitialised wake was in practice false (0).
I'm not sure that this counts as a bug, as I'm not sure that
it manifests in any unwanted behaviour. But in any case, the issue
was introduced by:
3ce7547e5b ("net: txgbe: Add build support for txgbe")
Flagged by Smatch as:
.../txgbe_main.c:486 txgbe_shutdown() error: uninitialized symbol 'wake'.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
