Aquantia AQR813 is the Octal Port variant of the AQR113. Add PHY ID for
it to provide support for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Aquantia AQR113 PHY ID. Aquantia AQR113 is just a chip size variant of
the already supported AQR133C where the only difference is the PHY ID
and the hw chip size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PMD Global Transmit Disable bit should be cleared for normal operation.
This should be HW default, however I found that on Asus RT-AX89X that uses
AQR113C PHY and firmware 5.4 this bit is set by default.
With this bit set the AQR cannot achieve a link with its link-partner and
it took me multiple hours of digging through the vendor GPL source to find
this out, so lets always clear this bit during .config_init() to avoid a
situation like this in the future.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240211181732.646311-1-robimarko@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After merging the net-next tree, today's linux-next build (x86_64
allmodconfig) failed like this:
drivers/net/phy/aquantia/aquantia_firmware.c: In function 'aqr_fw_load_memory':
drivers/net/phy/aquantia/aquantia_firmware.c:135:23: error: implicit declaration of function 'crc_ccitt_false'; did you mean 'crc_ccitt_byte'? [-Werror=implicit-function-declaration]
135 | crc = crc_ccitt_false(crc, crc_data, sizeof(crc_data));
| ^~~~~~~~~~~~~~~
| crc_ccitt_byte
Caused by commit e93984ebc1 ("net: phy: aquantia: add firmware load support")
interacting with commit ("lib: crc_ccitt_false() is identical to crc_itu_t()")
from the mm tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20231221130946.7ed9a805@canb.auug.org.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On further testing on BE target with kernel test robot, it was notice
that the endianness conversion for addr and CRC in fw_load_memory was
wrong.
Drop the cpu_to_le32 conversion for addr load as it's not needed.
Use get_unaligned_le32 instead of get_unaligned for FW data word load to
correctly convert data in the correct order to follow system endian.
Also drop the cpu_to_be32 for CRC calculation as it's wrong and would
cause different CRC on BE system.
The loaded word is swapped internally and MAILBOX calculates the CRC on
the swapped word. To correctly calculate the CRC to be later matched
with the one from MAILBOX, use an u8 struct and swap the word there to
keep the same order on both LE and BE for crc_ccitt_false function.
Also add additional comments on how the CRC verification for the loaded
section works.
CRC is calculated as we load the section and verified with the MAILBOX
only after the entire section is loaded to skip additional slowdown by
loop the section data again.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311210414.sEJZjlcD-lkp@intel.com/
Fixes: e93984ebc1 ("net: phy: aquantia: add firmware load support")
Tested-by: Robert Marko <robimarko@gmail.com> # ipq8072 LE device
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231128135928.9841-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aquantia PHY-s require firmware to be loaded before they start operating.
It can be automatically loaded in case when there is a SPI-NOR connected
to Aquantia PHY-s or can be loaded from the host via MDIO.
This patch adds support for loading the firmware via MDIO as in most cases
there is no SPI-NOR being used to save on cost.
Firmware loading code itself is ported from mainline U-boot with cleanups.
The firmware has mixed values both in big and little endian.
PHY core itself is big-endian but it expects values to be in little-endian.
The firmware is little-endian but CRC-16 value for it is stored at the end
of firmware in big-endian.
It seems the PHY does the conversion internally from firmware that is
little-endian to the PHY that is big-endian on using the mailbox
but mailbox returns a big-endian CRC-16 to verify the written data
integrity.
Co-developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MMD_VEND define to header to clean things up and in preparation for
firmware loading support that require some define placed in
aquantia_main.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move aquantia PHY driver to separate driectory in preparation for
firmware loading support to keep things tidy.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
