Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased) 493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci 830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223053111.29170-1-quic_bqiang@quicinc.com
Every time the firmware boots we call ath11k_core_qmi_firmware_ready() which
ends up calling ath11k_thermal_register(). So we try to register thermal
devices multiple times. And when we power off the firmware during
suspend/hibernation (implemented in the next patch) we get a warning in resume:
hwmon hwmon4: PM: parent phy0 should not be sleeping
Workaround this similarly like ath11k_mac_register() does by testing
ATH11K_FLAG_REGISTERED.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-6-quic_bqiang@quicinc.com
We are seeing below warning in both reset and suspend/resume scenarios:
[69663.691847] ath11k_pci 0000:02:00.0: Already processed, so ignoring dma ring caps
This is because ab->num_db_cap is not cleared in
ath11k_wmi_free_dbring_caps(), so clear it to avoid such
warnings.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-5-quic_bqiang@quicinc.com
Both the firmware reset feature and the power management
suspend/resume feature share common power-down and power-up
functionality. One aspect of the power-up functionality is
the handling of the ATH11K_QMI_EVENT_FW_INIT_DONE event.
When this event is received, a call is made to
ath11k_hal_dump_srng_stats(), with the purpose to collect
information that may be useful in debugging the cause of a
firmware reset.
Unfortunately, since this functionality is shared between
both the firmware reset path and the power management
resume path, the kernel log is flooded with messages during
resume. Since these messages are not useful during resume,
and in fact can be confusing and can increase the time it
takes to resume, update the logic to only call
ath11k_hal_dump_srng_stats() during firmware reset.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-4-quic_bqiang@quicinc.com
There is no driver to match these two channels, so
remove them. This fixes warnings from MHI subsystem during suspend:
mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting
mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-3-quic_bqiang@quicinc.com
For non WoW suspend/resume, ath11k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath11k reset logic.
In order to reuse that logic, rearrange IRQ handling in the reset
path.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-2-quic_bqiang@quicinc.com
ath.git patches for v6.9
We have support for QCA2066 now and also several new features in ath12k.
Major changes:
ath12k
* firmware-2.bin support
* support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
* QCN9274: support split-PHY devices
* WCN7850: enable Power Save Mode in station mode
* WCN7850: P2P support
ath11k:
* QCA6390 & WCN6855: support 2 concurrent station interfaces
* QCA2066 support
Currently, function to check if beacon countdown is complete uses deflink
to fetch the beacon and check the counter. However, with MLO, there is
a need to check the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240216144621.514385-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
QCA2066 is a PCI based DBS device. It is very similar to WCN6855
overall: they share the same PCI device ID, the same major and
minor version numbers, the same register address, and same HAL
descriptors etc. The most significant difference is that QCA2066
supports 3-antenna configuration while WCN6855 does not. To differentiate
them, subversion numbers are used. Currently four numbers are used
by QCA2066: 0x1019A0E1, 0x1019B0E1, 0x1019C0E1 and 0x1019D0E1.
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03737-QCAHSPSWPL_V2_SILICONZ_CE-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240109021336.4143-3-quic_bqiang@quicinc.com
In ath11k_pci_probe() there is a switch statement that, based
upon the PCI device ID, assigns pci_ops. After the switch,
ath11k_pcic_register_pci_ops() is called to register the pci_ops.
Unfortunately, this registration is too late if any of the cases
in the switch need to perform operations that require the pci_ops
to already be registered. In particular, an upcoming patch for
QCA2066 needs to call ath11k_pcic_read32().
To address this issue, call ath11k_pcic_register_pci_ops() from
each case instead of doing so after the switch. That way the ops
will be registered if any subsequent operations within the case
processing require the ops to be present.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240109021336.4143-2-quic_bqiang@quicinc.com
Provide address list to mac80211 so user doesn't need to specify addresses when
a second interface is added because the address can be allocated from the list
by mac80211.
The derived addresses have LAA (Local Administered Address) bit set, and only
the first byte is changed. Take the 00:03:7f:xx:xx:xx as example to derive:
addresses[0] is unchanged, it's still 00:03:7f:xx:xx:xx,
addresses[1] is 02:03:7f:xx:xx:xx,
addresses[2] is 12:03:7f:xx:xx:xx,
addresses[3] is 22:03:7f:xx:xx:xx,
addresses[4] is 32:03:7f:xx:xx:xx.
However as only 3 addresses are reported now, so addresses[3] and addresses[4]
aren't actually derived.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20230714023801.2621802-3-quic_cjhuang@quicinc.com
Add hardware parameter support_dual_stations to indicate whether 2 station
interfaces are supported. For chips which support this feature, limit total
number of AP interface and mesh point to 1. The max interfaces are 3 for such
chips.
The chips affected are:
QCA6390 hw2.0
WCN6855 hw2.0
WCN6855 hw2.1
Other chips are not affected.
For affected chips, remove radar_detect_widths because now
num_different_channels is set to 2. radar_detect_widths can be set only when
num_different_channels is 1, see mac80211 function wiphy_verify_combinations
for details. This means that in affectected chips DFS cannot be enabled in AP
mode.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20230714023801.2621802-2-quic_cjhuang@quicinc.com
Currently, function to update beacon counter uses deflink to fetch
the beacon and then update the counter. However, with MLO, there is
a need to update the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data during beacon update counter.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 9476cda44c ("wifi: ath11k: Consistently use ath11k_vif_to_arvif()")
previously replaced all open coding of the ath11k_vif_to_arvif()
functionality. Subsequently two more instances of open coding were
introduced, one in commit 92425f788f ("wifi: ath11k: fill parameters for
vdev set tpc power WMI command") and one in commit 6f4e235be6 ("wifi:
ath11k: add parse of transmit power envelope element"), so fix those as
well.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240205-ath11k_vif_to_arvif-v1-1-7c41313c8318@quicinc.com
Currently, at the end of ath11k_mac_fill_reg_tpc_info(), the
reg_tpc_info struct is populated, including the following:
reg_tpc_info->is_psd_power = is_psd_power;
reg_tpc_info->eirp_power = eirp_power;
Kernel test robot complains on uninitialized symbol:
drivers/net/wireless/ath/ath11k/mac.c:7949
ath11k_mac_fill_reg_tpc_info() error: uninitialized symbol 'eirp_power'.
This is because there are some code paths that never set eirp_power, so
the assignment of reg_tpc_info->eirp_power can come from an
uninitialized variable. Functionally this is OK since the eirp_power
only has meaning when is_psd_power is true, and all code paths which set
is_psd_power to true also set eirp_power. However, to keep the robot
happy, always initialize eirp_power before use.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 92425f788f ("wifi: ath11k: fill parameters for vdev set tpc power WMI command")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202024011.11341-1-quic_bqiang@quicinc.com
Currently in ath11k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160
are used to calculate max_nss, see
if (support_160)
max_nss = min(rx_mcs_80, rx_mcs_160);
else
max_nss = rx_mcs_80;
Kernel test robot complains on uninitialized symbols:
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath11k/mac.c:2323 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
This is because there are some code paths that never set them, so
the assignment of max_nss can come from uninitialized variables.
This could result in some unknown issues since a wrong peer_nss
might be passed to firmware.
Change to initialize them to an invalid value at the beginning. This
makes sense because even max_nss gets an invalid value, due to either
or both of them being invalid, we can get an valid peer_nss with
following guard:
arg->peer_nss = min(sta->deflink.rx_nss, max_nss)
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 3db26ecf71 ("ath11k: calculate the correct NSS of peer for HE capabilities")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202023547.11141-1-quic_bqiang@quicinc.com
Currently when connecting to an AP with 11AX-HE phy mode, host sends
WMI_VDEV_PARAM_SET_HEMU_MODE parameter to firmware after
WMI_PEER_ASSOC_CMDID command. This results in TXBF not working, because
firmware calculates TXBF values while handling WMI_PEER_ASSOC_CMDID,
however at that time WMI_VDEV_PARAM_SET_HEMU_MODE has not been sent yet.
See below log:
AP sends "VHT/HE/EHT NDP Announcement" to station, and station sends
"Action no Ack" of category code HE to AP, the "Nc Index" and
"Codebook Information" are wrong:
Issued action:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 152
HE MIMO Control: 0x0004008018
.... .... .... .... .... .... .... .... .... .000 = Nc Index: 1 Column (0)
.... .... .... .... .... .... .... ..0. .... .... = Codebook Information: 0
Change to send WMI_VDEV_PARAM_SET_HEMU_MODE before WMI_PEER_ASSOC_CMDID,
then firmware will calculate the TXBF values with valid parameters
instead of empty values. TXBF works well and throughput performance is
improved from 80 Mbps to 130 Mbps with this patch.
Good action after this patch:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 409
HE MIMO Control: 0x0004008219
.... .... .... .... .... .... .... .... .... .001 = Nc Index: 2 Columns (1)
.... .... .... .... .... .... .... ..1. .... .... = Codebook Information: 1
This change applies to all chipsets.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 38dfe775d0 ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240131021832.17298-1-quic_bqiang@quicinc.com
ath.git patches for v6.9
We have new features for both ath11k and ath12k. ath12k is now under
heavy refactoring in preparation for MLO support.
Major changes:
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
Currently ath11k_mac_op_unassign_vif_chanctx() deletes peer but
ath11k_mac_op_assign_vif_chanctx() doesn't create it. This results in
connection failure if MAC80211 calls drv_unassign_vif_chanctx() and
drv_assign_vif_chanctx() during AUTH and ASSOC, see below log:
[ 102.372431] wlan0: authenticated
[ 102.372585] ath11k_pci 0000:01:00.0: wlan0: disabling HT/VHT/HE as WMM/QoS is not supported by the AP
[ 102.372593] ath11k_pci 0000:01:00.0: mac chanctx unassign ptr ffff895084638598 vdev_id 0
[ 102.372808] ath11k_pci 0000:01:00.0: WMI vdev stop id 0x0
[ 102.383114] ath11k_pci 0000:01:00.0: vdev stopped for vdev id 0
[ 102.384689] ath11k_pci 0000:01:00.0: WMI peer delete vdev_id 0 peer_addr 20:e5:2a:21:c4:51
[ 102.396676] ath11k_pci 0000:01:00.0: htt peer unmap vdev 0 peer 20:e5:2a:21:c4:51 id 3
[ 102.396711] ath11k_pci 0000:01:00.0: peer delete resp for vdev id 0 addr 20:e5:2a:21:c4:51
[ 102.396722] ath11k_pci 0000:01:00.0: mac removed peer 20:e5:2a:21:c4:51 vdev 0 after vdev stop
[ 102.396780] ath11k_pci 0000:01:00.0: mac chanctx assign ptr ffff895084639c18 vdev_id 0
[ 102.400628] wlan0: associate with 20:e5:2a:21:c4:51 (try 1/3)
[ 102.508864] wlan0: associate with 20:e5:2a:21:c4:51 (try 2/3)
[ 102.612815] wlan0: associate with 20:e5:2a:21:c4:51 (try 3/3)
[ 102.720846] wlan0: association with 20:e5:2a:21:c4:51 timed out
The peer delete logic in ath11k_mac_op_unassign_vif_chanctx() is
introduced by commit b4a0f54156 ("ath11k: move peer delete after
vdev stop of station for QCA6390 and WCN6855") to fix firmware
crash issue caused by unexpected vdev stop/peer delete sequence.
Actually for a STA interface peer should be deleted in
ath11k_mac_op_sta_state() when STA's state changes from
IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST, which also coincides
with current peer creation design that peer is created during
IEEE80211_STA_NOTEXIST -> IEEE80211_STA_NONE transition. So move
peer delete back to ath11k_mac_op_sta_state(), also stop vdev before
deleting peer to fix the firmware crash issue mentioned there. In
this way the connection failure mentioned here is also fixed.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: b4a0f54156 ("ath11k: move peer delete after vdev stop of station for QCA6390 and WCN6855")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-5-quic_bqiang@quicinc.com
In ath11k_mac_op_assign_vif_chanctx(), there is a logic to
create peer using ar->mac_addr for a STA vdev. This is invalid
because a STA vdev should have a peer created using AP's
MAC address. Besides, if we run into that logic, it means a peer
has already been created earlier, we should not create it again.
So remove it.
This is found during code review.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-2-quic_bqiang@quicinc.com
Currently 32 bit DMA mask is used, telling kernel to get us an DMA
address under 4GB when mapping a buffer. This results in a very high
CPU overhead in the case where IOMMU is disabled and more than 4GB
system memory is installed. The reason is, with more than 4GB memory
installed, kernel is likely to allocate a buffer whose physical
address is above 4GB. While with IOMMU disabled, kernel has to involve
SWIOTLB to map/unmap that buffer, which consumes lots of CPU cycles.
We did hit an issue caused by the reason mentioned above: in a system
that disables IOMMU and gets 8GB memory installed, a total of 40.5%
CPU usage is observed in throughput test. CPU profiling shows nearly
60% of CPU cycles are consumed by SWIOTLB.
By enabling 36 bit DMA mask, we can bypass SWIOTLB for any buffer
whose physical address is below 64GB. There are two types of DMA mask
within struct device, named dma_mask and coherent_dma_mask. Here we
only enable 36 bit for dma_mask, because firmware crashes if
coherent_dma_mask is also enabled, due to some unknown hardware
limitations. This is acceptable because coherent_dma_mask is used for
mapping a consistent DMA buffer, which generally does not happen in
a hot path.
With this change, the total CPU usage mentioned in above issue drops
to 18.9%.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123015201.28939-1-quic_bqiang@quicinc.com
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Link: https://lore.kernel.org/r/20240122153434.E0254C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 7636c9a6e7 ("wifi: ath11k: Add multi TX ring support for WCN6750")
added HAL_RX_BUF_RBM_SW4_BM to enum hal_rx_buf_return_buf_manager. However,
as flagged by the kernel-doc script, the documentation was not updated:
drivers/net/wireless/ath/ath11k/hal.h:689: warning: Enum value 'HAL_RX_BUF_RBM_SW4_BM' not described in enum 'hal_rx_buf_return_buf_manager'
So update the documentation. No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240111-document-hal_rx_buf_rbm_sw4_bm-v1-1-ad277e8ab3cc@quicinc.com
When station is connected to a 6 GHz AP, it has 2 ways to configure
the power limit to firmware. The first way is to send 2 WMI commands
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to
firmware, the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to
firmware which include more parameters for power control.
When firmware supports SERVICE_EXT_TPC_REG, it means firmware supports
WMI_VDEV_SET_TPC_POWER_CMDID, then ath11k selects the second way.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-13-quic_bqiang@quicinc.com
There are two power types for 6 GHz regulatory, one is AP, another
is client.
When firmware boots up, WMI_REG_CHAN_LIST_CC_EXT_EVENTID is sent from
firmware at an early stage, the interface mode is not decided at
this point, then ath11k select reg rules of AP type as default.
After interface is created, it is exactly decided the interface
type such as AP/mesh point/station. Then ath11k need to update
reg rules to the exact power type matched to the interface type.
The client power type is used for station interface, and AP power
type is used for AP/mesh point interface.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-5-quic_bqiang@quicinc.com
spin_lock()/spin_unlock() are used in ath11k_reg_chan_list_event() to
acquire/release ab->base_lock. For now this is safe because that
function is only called in soft IRQ context.
But ath11k_reg_chan_list_event() will be called from process
context in an upcoming patch, and this can result in a deadlock if
ab->base_lock is acquired in process context and then soft IRQ occurs
on the same CPU and tries to acquire that lock.
Fix it by using spin_lock_bh() and spin_unlock_bh() instead.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 69a0fcf8a9 ("ath11k: Avoid reg rules update during firmware recovery")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-4-quic_bqiang@quicinc.com
The regulatory info of WMI_REG_CHAN_LIST_CC_EXT_EVENTID is not saved
in ath11k now, the info should be saved in ath11k. Save the info for
each radio and support switch regulatory rules dynamically.
As mac.c will also call ath11k_reg_handle_chan_list() in next patches move the
function to reg.c.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231218085844.2658-3-quic_bqiang@quicinc.com
virt_to_phys() doesn't work on systems with IOMMU enabled, which have
non-identity physical-to-IOVA mappings. It leads to IO_PAGE_FAULTs like this:
[IO_PAGE_FAULT domain=0x0023 address=0x1cce00000 flags=0x0020]
And no association to the AP can be established.
This patch changes that to dma_map_single(), which works correctly. Even
virt_to_phys() documentation says device drivers should not use it:
This function does not give bus mappings for DMA transfers. In
almost all conceivable cases a device driver should not be using
this function
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Zhenghao Gu <imguzh@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231212031914.47339-1-imguzh@gmail.com
Since 'ath11k_wmi_tlv_parse_alloc()' always operates on
'skb->data, skb->len' tuple, it may be simplified to pass
the only 'skb' argument instead (which also implies
refactoring of 'ath11k_pull_bcn_tx_status_ev()' and
'ath11k_pull_chan_info_ev()' in the same way). Compile
tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161117.75145-1-dmantipov@yandex.ru
In v6.7-rc1 sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
Workaround the warnings by refactoring the code to a new function, which also
reduces code duplication. And in the new function use max3() to make the code
more readable.
No functional changes, compile tested only.
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161740.1582340-1-kvalo@kernel.org
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231117093056.873834-9-u.kleine-koenig@pengutronix.de
