In brcmf_chip_recognition(), the return value from an MMIO read is
interpreted as various fields without checking if it failed, which is
harmless today, as the interpreted fields are checked for validity a
few lines below. However, in corner cases (on my MacbookPro 14,1,
sometimes after waking from sleep or soft reboot), when this happens,
it causes the logging to be misleading, because the message indicates
an unsupported chip type ("brcmfmac: brcmf_chip_recognition: chip
backplane type 15 is not supported"). This patch detects this case
slightly earlier and logs an appropriate message, with the same return
result as is the case today.
Signed-off-by: Neal Sidhwaney <nealsid@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230603060021.57225-1-nealsid@gmail.com
At least on BCM4387, the D11 cores are held in reset on cold startup and
firmware expects to release reset itself. Just assert reset here and let
firmware deassert it. Premature deassertion results in the firmware
failing to initialize properly some of the time, with strange AXI bus
errors.
Also, BCM4387 has 3 cores, up from 2. The logic for handling that is in
brcmf_chip_ai_resetcore(), but since we aren't using that any more, just
handle it here.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214092423.15175-1-marcan@marcan.st
The commit that introduced support for this chip incorrectly claimed it
is a Cypress-specific part, while in actuality it is just a variant of
BCM4355 silicon (as evidenced by the chip ID).
The relationship between Cypress products and Broadcom products isn't
entirely clear but given what little information is available and prior
art in the driver, it seems the convention should be that originally
Broadcom parts should retain the Broadcom name.
Thus, rename the relevant constants and firmware file. Also rename the
specific 89459 PCIe ID to BCM43596, which seems to be the original
subvariant name for this PCI ID (as defined in the out-of-tree bcmdhd
driver).
Since Cypress added this part and will presumably be providing its
supported firmware, we keep the CYW designation for this device.
We also drop the RAW device ID in this commit. We don't do this for the
other chips since apparently some devices with them exist in the wild,
but there is already a 4355 entry with the Broadcom subvendor and WCC
firmware vendor, so adding a generic fallback to Cypress seems
redundant (no reason why a device would have the raw device ID *and* an
explicitly programmed subvendor).
Fixes: dce45ded76 ("brcmfmac: Support 89459 pcie")
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230212063813.27622-2-marcan@marcan.st
Add HW and SDIO ids for use with the SparkLan AP6275S
Add the firmware mapping structures for the BRCM43752 chipset.
The 43752 needs some things setup similar to the 43012 chipset.
The WATERMARK shows better performance when initialized to the 4373 value.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812165218.2508258-2-angus@akkea.ca
The 2018 13" MacBook Pro (MacBookPro15,2) has a Broadcom chip, the 4364.
This chip appears to be specific to Apple and is not found in other
hardware.
Add this chip to the brcmfmac driver so that it can be recognized
automatically. Note that the PCI device id is 4464 even though the chip
is referred to as the 4364.
Signed-off-by: brian m. carlson <sandals@crustytoothpaste.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer 4359 chip revisions need a different rambase address.
This fixes firmware download on such devices which fails otherwise.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two D11 cores in RSDB chips like 4359. We have to reset two
D11 cores simutaneously before firmware download, or the firmware may
not be initialized correctly and cause "fw initialized failed" error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_get_regaddr:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:790:5: warning: variable mpnum set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:10: warning: variable nsp set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:5: warning: variable nmp set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
- Allow GCI to be added to core list even when it doesn't have a wrapper.
- Allow 8K address space size.
- Don't overwrite the address value when an additional size descriptor
is in place.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM4366E is a wireless chipset with a BCM43664 ChipCommon. It's
supported by the same firmware as 4366c0.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
[arend: rebase patch and remove unnecessary definition]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The chip id can either be four or five digits. For the chip name either
the hexadecimal value needs to be taken (four digits) or the decimal
value (five digits). The function brcmf_chip_name() does this conversion
so use it to store the name in driver revision info.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add 43455 into the save-restore(SR) capable chip list, so
the SR engine will be enabled with 43455 FW which built-in the -sr
function.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On recent Broadcom chipsets PMU is present as separated core and it
can't be accessed using ChipCommon anymore as it fails with e.g.:
[ 18.198412] Unhandled fault: imprecise external abort (0x1406) at 0xb6da200f
Add a new helper function that will return a proper core that should be
used for accessing PMU registers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is an extra bitfield with info about some present hardware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Separated PMU core can be found in new devices and should be used for
accessing PMU registers (which were routed through ChipCommon so far).
This core is one of exceptions that doesn't have or need wrapper address
to be still safely accessible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far we were looking for address descriptors without a check for
crossing current component border. In case of dealing with unsupported
descriptor or descriptor missing at all the code would incorrectly get
data from another component.
Consider this binary-described component from BCM4366 EROM:
4bf83b01 TAG==CI CID==0x83b
20080201 TAG==CI PORTS==0+1 WRAPPERS==0+1
18400035 TAG==ADDR SZ_SZD TYPE_SLAVE
00050000
18107085 TAG==ADDR SZ_4K TYPE_SWRAP
Driver was assigning invalid base address to this core:
brcmfmac: [6 ] core 0x83b:32 base 0x18109000 wrap 0x18107000
which came from totally different component defined in EROM:
43b36701 TAG==CI CID==0x367
00000201 TAG==CI PORTS==0+1 WRAPPERS==0+0
18109005 TAG==ADDR SZ_4K TYPE_SLAVE
This change will also allow us to support components without wrapper
address in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Part of reorganising wireless drivers directory and Kconfig. Note that I had to
edit Makefiles from subdirectories to use the new location.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
