In multi-channel scenarios, the granted channel must be aborted before
suspending. Otherwise, the firmware will be put into a wrong state,
resulting in an association failure after resuming.
With this patch, the granted channel will be aborted before suspending
if necessary.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To avoid using incorrect 6g power settings after disconnection,
it should to update back to the default state when disconnected.
Fixes: 51ba0e3a15 ("wifi: mt76: mt7921: add 6GHz power type support for clc")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are several power type should be supported in 6GHz band. mt7921
apply 6GHz power type from AP settings and clc will setup the
corresponding regulatory power.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move the following shared usb routines in mt792x module:
- mt792xu_stop
- mt792x_stop
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move struct ieee80211_chanctx_conf up to struct mt76_vif to allow the
connac2 library can access the struct ieee80211_chanctx_conf * member in
struct mt76_vif.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: David Ruth <druth@chromium.org>
Tested-by: David Ruth <druth@chromium.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When drv_tx calls race against local tx scheduling, the queue fill status checks
can potentially race, leading to dma queue entries being overwritten.
Fix this by deferring packets from drv_tx calls to the tx worker, in order to
ensure that all regular queue tx comes from the same context.
Reported-by: Ryder Lee <Ryder.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There were are a number of cases in mac80211 and iwlwifi (at
least) that used the sband->iftype_data pointer directly,
instead of using the accessors to find the right array entry
to use.
Make sparse warn when such a thing is done.
To not have a lot of casts, add two helper functions/macros
- ieee80211_set_sband_iftype_data()
- for_each_sband_iftype_data()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move acpi_sar code in mt792x-lib module since it is shared between
mt7921 and mt7925 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reduce duplicated code moving mac shared code in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt792x-lib module will contain the shared code between mt7921 and new
MT79 WiFi7 chipset
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ampdu_state field is used by most of the drivers, so move it in
mt76_wcid structure.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on poll_list field in mt76_wcid structure and get rid of
private copy.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure
and get rid of private copies.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_connac2_mac_fill_txs() counts tx_nss but ethtool doesn't show
stats. Add missing histogram accordingly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get missing tx retries/failed counts from txfree done events and report
them via mt7921_sta_statistics().
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7921 support following antenna combiantions only.
* primary + secondary (2x2)
* primary only (1x1)
Since we cannot work on secondary antenna only, return error if the
antenna bitmap is 0x2 in .set_antenna().
For example:
iw phy0 set antenna 3 3 /* valid */
iw phy0 set antenna 1 1 /* valid */
iw phy0 set antenna 2 2 /* invalid */
Cc: stable@vger.kernel.org
Fixes: e0f9fdda81 ("mt76: mt7921: add ieee80211_ops")
Suggested-by: Knox Chiou <knoxchiou@google.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kalle Valo says:
====================
wireless-next patches for v6.4
Most likely the last -next pull request for v6.4. We have changes all
over. rtw88 now supports SDIO bus and iwlwifi continues to work on
Wi-Fi 7 support. Not much stack changes this time.
Major changes:
cfg80211/mac80211
- fix some Fine Time Measurement (FTM) frames not being bufferable
- flush frames before key removal to avoid potential unencrypted
transmission depending on the hardware design
iwlwifi
- preparation for Wi-Fi 7 EHT and multi-link support
rtw88
- SDIO bus support
- RTL8822BS, RTL8822CS and RTL8821CS SDIO chipset support
rtw89
- framework firmware backwards compatibility
brcmfmac
- Cypress 43439 SDIO support
mt76
- mt7921 P2P support
- mt7996 mesh A-MSDU support
- mt7996 EHT support
- mt7996 coredump support
wcn36xx
- support for pronto v3 hardware
ath11k
- PCIe DeviceTree bindings
- WCN6750: enable SAR support
ath10k
- convert DeviceTree bindings to YAML
* tag 'wireless-next-2023-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (261 commits)
wifi: rtw88: Update spelling in main.h
wifi: airo: remove ISA_DMA_API dependency
wifi: rtl8xxxu: Simplify setting the initial gain
wifi: rtl8xxxu: Add rtl8xxxu_write{8,16,32}_{set,clear}
wifi: rtl8xxxu: Don't print the vendor/product/serial
wifi: rtw88: Fix memory leak in rtw88_usb
wifi: rtw88: call rtw8821c_switch_rf_set() according to chip variant
wifi: rtw88: set pkg_type correctly for specific rtw8821c variants
wifi: rtw88: rtw8821c: Fix rfe_option field width
wifi: rtw88: usb: fix priority queue to endpoint mapping
wifi: rtw88: 8822c: add iface combination
wifi: rtw88: handle station mode concurrent scan with AP mode
wifi: rtw88: prevent scan abort with other VIFs
wifi: rtw88: refine reserved page flow for AP mode
wifi: rtw88: disallow PS during AP mode
wifi: rtw88: 8822c: extend reserved page number
wifi: rtw88: add port switch for AP mode
wifi: rtw88: add bitmap for dynamic port settings
wifi: rtw89: mac: use regular int as return type of DLE buffer request
wifi: mac80211: remove return value check of debugfs_create_dir()
...
====================
Link: https://lore.kernel.org/r/20230421104726.800BCC433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
FIF_* flags from mac80211 is not ABI. mt7921 should not pass it into mcu
directly. Remap FIF_* to driver defined flags as mcu command input.
Fixes: c222f77fd4 ("wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent")
Signed-off-by: Neil Chen <yn.chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Should not use AND operator to check vif type NL80211_IFTYPE_MONITOR, and
that will cause we go into sniffer command for both STA and MONITOR
mode. However, the sniffer command would set channel properly (with some
extra options), the STA mode still works even if using the wrong
command.
Fix vif type check to make sure we using the right command to update
channel.
Fixes: 914189af23 ("wifi: mt76: mt7921: fix channel switch fail in monitor mode")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to get EHT rate stats from ethtool.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The rx filter, in mt7921 series, may be changed in fw operation. There is
a racing problem if rx filter controlled by both driver and firmware at
the same time. To avoid this issue, let mt7921 driver set rx filter by new
command MCU_CE_CMD_SET_RX_FILTER and allow the firmware controlling it
only.
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Neil Chen <yn.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the chanctx enabled, IEEE80211_CONF_CHANGE_CHANNEL in .config()
would not be called anymore. mt76 cannot control RF channel for monitor.
Add monitor type set-channel flow in .change_chanctx().
Fixes: 41ac53c899 ("wifi: mt76: mt7921: introduce chanctx support")
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When mt7921_abort_roc is called with dev->mutex held, it can deadlock while
calling cancel_work_sync(&phy->roc_work), because the work function could
be waiting to acquire the mutex.
Fix this by flushing the work before taking the mutex
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Fixes: 034ae28b56 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Fixes: 41ac53c899 ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We should update CLC config before SAR set to synchronize all
related settings.
Fixes: 23bdc5d8ca ("wifi: mt76: mt7921: introduce Country Location Control support")
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware can have the capability to manage the channel context
scheduling on multiple roles running on the device including Station,
AP and P2P GC/GO mode (will be extended based on the future patchset)
to help users sharing the network with others on a single device.
The firmware is able to support the channel chanctx up to 2 interface
simultaneously running on the different channels.
Another thing to be noted is that before the driver is going sent out the
management frames, the driver has to get the privilege from the firmware
to occupy the current channel context until the frame handshake is
completed and then get the privilege back to the firmware.
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce remain_on_channel support. Additionally, we add
mt7921_check_offload_capability to disable .remain_on_channel and
.cancel_remain_on_channel and related configuration because those
operations would rely on the fundamental MCU commands that will be only
supported with newer firmware.
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a chanctx parameter to mt76_connac_mcu_uni_add_bss signature to allow
the firmware binds the BSS into the specific channel context.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We should reset mstat->airtime_ac along with clear up the entries in the
hardware WLAN table for the Rx and Rx accumulative airtime. Otherwsie, the
value msta->airtime_ac - [tx, rx]_last may be a negative and that is not
the actual airtime the device took in the last run.
Reported-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7921_mutex_acquire at mt7921_[start, stop]_ap to fix the race
with the context holding dev->muxtex and the driver might access the
device in low power state.
Fixes: 24299fc869 ("mt76: mt7921: enable rx header traslation offload")
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7921_mutex_acquire at mt7921_[start, stop]_ap to fix the race
with the context holding dev->muxtex and the driver might access the
device in low power state.
Fixes: 9d958b60eb ("mt76: mt7921: fix command timeout in AP stop period")
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 patches for 5.20
- preparation for new chipset support
- fixes
- VHT/HE related improvements
- ACPI SAR support
[kvalo@kernel.org: fix mac80211 API changes in start_ap() and stop_ap()]
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce len to __mt76_mcu_msg_alloc signature in order to add the
capability to specify two different value for allocation and copy length.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The current driver has worked with HW beacon filter and connection
monitor all the way, here we move the enablement into the initialization
stage like other HW features being done to get rid of others are
confused why these configurations would be changed at runtime.
We still leave a way to turn off these offload features in debugfs knobs
but that is just for debugging purposes.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware beacon filter works whether or not the PM flag is set, so we
drop redundant dependency checks on PM flags.
Additionally, the patch implicitly allow the MT7921[E, S, U] to have a
consistent configuration of the hardware beacon filter.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
