Commit e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at
correct rate") breaks the dw UARTs on Intel Bay Trail (BYT) and
Cherry Trail (CHT) SoCs.
Before this change the RTL8732BS Bluetooth HCI which is found
connected over the dw UART on both BYT and CHT boards works properly:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: RTL: fw version 0x365d462e
where as after this change probing it fails:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: command 0xfc20 tx timeout
Bluetooth: hci0: RTL: download fw command failed (-110)
Revert the changes to fix this regression.
Fixes: e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at correct rate")
Cc: stable@vger.kernel.org
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Collingbourne <pcc@google.com>
Link: https://lore.kernel.org/r/20240317214123.34482-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
When userspace opens the console, we call set_termios() passing a
termios with the console's configured baud rate. Currently this causes
dw8250_set_termios() to disable and then re-enable the UART clock at
the same frequency as it was originally. This can cause corruption
of any concurrent console output. Fix it by skipping the reclocking
if we are already at the correct rate.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240222192635.1050502-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # 8250_bcm*
Link: https://lore.kernel.org/r/20231110152927.70601-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-9-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: VAMSHI GAJJELA <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20220713131722.2316829-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure LSR flags are preserved in dw8250_tx_wait_empty(). This
function is called from a low-level out function and therefore cannot
call serial_lsr_in() as it would lead to infinite recursion.
It is borderline if the flags need to be saved here at all since this
code relates to writing LCR register which usually implies no important
characters should be arriving.
Fixes: 914eaf935e ("serial: 8250_dw: Allow TX FIFO to drain before writing to UART_LCR")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW based controllers like the one on Renesas RZ/N1 must be programmed as
flow controllers when using DMA.
* Table 11.45 of the system manual, "Flow Control Combinations", states
that using UART with DMA requires setting the DMA in the peripheral
flow controller mode regardless of the direction.
* Chapter 11.6.1.3 of the system manual, "Basic Interface Definitions",
explains that the burst size in the above case must be configured in
the peripheral's register DEST/SRC_BURST_SIZE.
Experiments shown that upon Rx timeout, the DMA transaction needed to be
manually cleared as well.
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use device tree match data rather than multiple calls to
of_device_is_compatible() by introducing a platform data structure and
adding a quirks mask.
Provide a stub to the compatibles without quirks to simplify the
handling of the upcoming changes.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
[<miquel.raynal@bootlin.com: Minor changes + creation of a real pdata structure]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the StarFive JH7100 RISC-V SoC the UART core clocks can't be set to
exactly 16 * 115200Hz and many other common bitrates. Trying this will
only result in a higher input clock, but low enough that the UART's
internal divisor can't come close enough to the baud rate target.
So rather than try to set the input clock it's better to skip the
clk_set_rate call and rely solely on the UART's internal divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
The driver was updating the port uartclk before setting the new rate in
an attempt to avoid having the clock notifier redundantly update the
divisors.
The set_termios() callback is however called under the termios semaphore
and tty-port mutex so the worker scheduled by the clock notifier will
block in serial8250_update_uartclk() until the uartclk and divisors have
been updated anyway.
Drop the unnecessary swaps and incorrect comment and simply update the
uartclk field if the clock-rate change was successful.
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored except deferred probe. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190925162617.30368-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
