Simplify 'xhci_try_enable_msi()' and reduce unnecessary function calls.
xHCI driver first tries to allocate 'num_online_cpu()' number of MSI-X
vectors, if that fails it falls back to a single MSI vector. There is no
good reason for this, we currently only support a primary interrupter.
However, we are still interested in knowing if there are more vectors
available, which will be utilized once we get secondary interrupter
support.
Call 'pci_alloc_irq_vectors()' once (with MSI-X and MSI flag), instead
of separately for MSI-X and MSI. And accept any number of MSI-X or MSI
vectors between 1 and 'num_online_cpu()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commits 7b8ef22ea5 ("usb: xhci: plat: Add USB phy support") and
9134c1fd05 ("usb: xhci: plat: Add USB 3.0 phy support") added support
for looking up legacy PHYs from the sysdev devicetree node and
initialising them.
This broke drivers such as dwc3 which manages PHYs themself as the PHYs
would now be initialised twice, something which specifically can lead to
resources being left enabled during suspend (e.g. with the
usb_phy_generic PHY driver).
As the dwc3 driver uses driver-name matching for the xhci platform
device, fix this by only looking up and initialising PHYs for devices
that have been matched using OF.
Note that checking that the platform device has a devicetree node would
currently be sufficient, but that could lead to subtle breakages in case
anyone ever tries to reuse an ancestor's node.
Fixes: 7b8ef22ea5 ("usb: xhci: plat: Add USB phy support")
Fixes: 9134c1fd05 ("usb: xhci: plat: Add USB 3.0 phy support")
Cc: stable@vger.kernel.org # 4.1
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Stanley Chang <stanley_chang@realtek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Tested-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231103164323.14294-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
There is a 120ms delay implemented for allowing the XHCI host controller to
detect a U3 wakeup pulse. The intention is to wait for the device to retry
the wakeup event if the USB3 PORTSC doesn't reflect the RESUME link status
by the time it is checked. As per the USB3 specification:
tU3WakeupRetryDelay ("Table 7-12. LTSSM State Transition Timeouts")
This would allow the XHCI resume sequence to determine if the root hub
needs to be also resumed. However, in case there is no device connected,
or if there is only a HSUSB device connected, this delay would still affect
the overall resume timing.
Since this delay is solely for detecting U3 wake events (USB3 specific)
then ignore this delay for the disconnected case and the HSUSB connected
only case.
[skip helper function, rename usb3_connected variable -Mathias ]
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this driver enables the xHC clocks while resuming from sleep, it calls
clk_prepare_enable() without checking for errors and blithely goes on to
read/write the xHC's registers -- which, with the xHC not being clocked,
at least on ARM32 usually causes an imprecise external abort exceptions
which cause kernel oops. Currently, the chips for which the driver does
the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based
on ARM32 CPUs, as it seems...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 8bd954c561 ("usb: host: xhci-plat: suspend and resume clocks")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some situations where xhci removal happens parallel to xhci_handshake,
we encounter a scenario where the xhci_handshake can't succeed, and it
polls until timeout.
If xhci_handshake runs until timeout it can on some platforms result in
a long wait which might lead to a watchdog timeout.
Add a helper that checks xhci status during the handshake, and exits if
set state is entered. Use this helper in places where xhci_handshake is
called unlocked and has a long timeout. For example xhci command timeout
and xhci reset.
[commit message and code comment rewording -Mathias]
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current function that both removes and frees an interrupter isn't
optimal when using several interrupters. The array of interrupters need
to be protected with a lock while removing interrupters, but the default
xhci spin lock can't be used while freeing the interrupters event ring
segment table as dma_free_coherent() should be called with IRQs enabled.
There is no need to free the interrupter under the lock, so split this
code into separate unlocked free part, and a lock protected remove part.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase the event ring dequeue pointer for port change events in the
same way as other event types. No need to handle it separately.
This only touches the driver side tracking of event ring dequeue.
Note: this does move forward the event ring dequeue increase for port
change events a bit.
Previously the dequeue was increased before temporarily dropping
the xhci lock while kicking roothub polling.
Now dequeue is increased after re-aquiring the lock.
This should not matter as event ring dequeue is not touched at all by
hub thread. It's only touched in xhci interrupt handler.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No matter what type of event we receive we want to increase the event
ring dequeue pointer one step for every event that is handled.
For unknown reasons the event ring dequeue increase is done inside the
transfer event handler and port event handler.
As the transfer event handler got more complex and can now loop through
several transfer TRBs on a transfer ring, there were additinal checks
added to avoid increasing event ring dequeue more than one step.
No need for elaborate checks to avoid increasing event ring dequeue
in case the transfer event handler goes through a loop.
Just increasing the event ring dequeue outside the transfer event
handler.
End goal is to increase event ring dequeue in just one place.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initial xhci_ring allocation has just been amended to assign a
monotonically increasing number to each ring segment.
However rings may be expanded after initial allocation.
So number newly inserted segments starting from the preceding segment in
the ring and renumber all segments succeeding the newly inserted ones.
This is not a fix because ring expansion currently isn't done on the
Event Ring and that's the only ring type using the segment number.
It's just in preparation for when either Event Ring expansion is added
or when other ring types start making use of the segment number.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The next_trb() helper relies on a link TRB at the end of a ring segment
to know a segment ends. This works well with transfer rings that use
link trbs, but not with event rings.
Event rings segments are always filled by host to segment size
before moving to next segment. It does not use link TRBs
Check for both link trb and full segment in next_trb() helper to
support event rings.
Useful if several interrupters with several event rings are supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f ("xhci: Refactor interrupter code for initial multi interrupter support.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Event Handler Busy bit shall be cleared by software when the Event
Ring is empty. The xHC is thereby informed that it may raise another
interrupt once it has enqueued new events (sec 4.17.2).
However since commit dc0ffbea57 ("usb: host: xhci: update event ring
dequeue pointer on purpose"), the EHB bit is already cleared after half
a segment has been processed.
As a result, spurious interrupts may occur:
- xhci_irq() processes half a segment, clears EHB, continues processing
remaining events.
- xHC enqueues new events. Because EHB has been cleared, xHC sets
Interrupt Pending bit. Interrupt moderation countdown begins.
- Meanwhile xhci_irq() continues processing events. Interrupt
moderation countdown reaches zero, so an MSI interrupt is signaled.
- xhci_irq() empties the Event Ring, clears EHB again and is done.
- Because an MSI interrupt has been signaled, xhci_irq() is run again.
It discovers there's nothing to do and returns IRQ_NONE.
Avoid by clearing the EHB bit only at the end of xhci_irq().
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.5+
Cc: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-hub.c tracks suspended ports in a suspended_port bitfield.
This is checked when responding to a Get_Status(PORT) request to see if a
port in running U0 state was recently resumed, and adds the required
USB_PORT_STAT_C_SUSPEND change bit in those cases.
The suspended_port bit was left uncleared if a device is disconnected
during suspend. The bit remained set even when a new device was connected
and enumerated. The set bit resulted in a incorrect Get_Status(PORT)
response with a bogus USB_PORT_STAT_C_SUSPEND change
bit set once the new device reached U0 link state.
USB_PORT_STAT_C_SUSPEND change bit is only used for USB2 ports, but
xhci-hub keeps track of both USB2 and USB3 suspended ports.
Cc: stable@vger.kernel.org
Reported-by: Wesley Cheng <quic_wcheng@quicinc.com>
Closes: https://lore.kernel.org/linux-usb/d68aa806-b26a-0e43-42fb-b8067325e967@quicinc.com/
Fixes: 1d5810b692 ("xhci: Rework port suspend structures for limited ports.")
Tested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned in:
commit 474ed23a62 ("xhci: align the last trb before link if it is
easily splittable.")
A bounce buffer is utilized for ensuring that transfers that span across
ring segments are aligned to the EP's max packet size. However, the device
that is used to map the DMA buffer to is currently using the XHCI HCD,
which does not carry any DMA operations in certain configrations.
Migration to using the sysdev entry was introduced for DWC3 based
implementations where the IOMMU operations are present.
Replace the reference to the controller device to sysdev instead. This
allows the bounce buffer to be properly mapped to any implementations that
have an IOMMU involved.
cc: stable@vger.kernel.org
Fixes: 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calculate the IN/OUT budget separately to improve the bandwidth schedule,
meanwhile should avoid Start-Split token overlap between IN and OUT
endpoints, and take into account the FS/LS bandwidth boundary in each
microframe and also in each FS frame.
Calculate the budget for SS of OUT eps and CS of IN eps, but not include
extra-cs, and always add at most extra-cs allowed.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230830122820.18859-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
