This adds support for using CS42L42 as a SoundWire device.
SoundWire-specifics are kept separate from the I2S implementation as
much as possible, aiming to limit the risk of breaking the I2C+I2S
support.
There are some important differences in the silicon behaviour between
I2S and SoundWire mode that are reflected in the implementation:
- ASP (I2S) most not be used in SoundWire mode because the two interfaces
share pins.
- The SoundWire capture (record) port only supports 1 channel. It does
not have left-to-right duplication like the ASP.
- DP2 can only be prepared if the HP has powered-up. DP1 can only be
prepared if the ADC has powered-up. (This ordering restriction does
not exist for ASPs.) The SoundWire core port-prepare step is
triggered by the DAI-link prepare(). This happens before the
codec DAI prepare() or the DAPM sequence so these cannot be used
to enable HP/ADC. Instead the HP/ADC enable/disable are done during
the port_prep callback.
- The SRCs are an integral part of the audio chain but in silicon their
power control is linked to the ASP. There is no equivalent power link
to SoundWire DPs so the driver must take "manual" control of SRC power.
- The SoundWire control registers occupy the lower part of the SoundWire
address space so cs42l42 registers are offset by 0x8000 (non-paged) in
SoundWire mode.
- Register addresses are 8-bit paged in I2C mode but 16-bit unpaged in
SoundWire.
- Special procedures are needed on register read/writes to (a) ensure
that the previous internal bus transaction has completed, and
(b) handle delayed read results, when the read value could not be
returned within the SoundWire read command.
There are also some differences in driver implementation between I2S
and SoundWire operation:
- CS42L42 I2S does not runtime_suspend, but runtime_suspend/resume support
has been added into the driver in SoundWire mode as the most convenient
way to power-up the bus manager and to handle the unattach_request
condition, though the CS42L42 chip does not itself suspend or resume.
- Intel SoundWire host controllers have a low-power clock-stop mode that
requires resetting all peripherals when resuming. This means that the
interrupt registers will be reset in between the interrupt being
generated and the interrupt being handled, and since the interrupt
status is debounced, these values may not be accurate immediately,
and may cause spurious unplug events before settling.
- As in I2S mode, the PLL is only used while audio is active because
of clocking quirks in the silicon. For SoundWire the cs42l42_pll_config()
is deferred until the DAI prepare(), to allow the cs42l42_bus_config()
callback to set the SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-7-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit dcc2c012c7 ("ASoC: Fix gpiolib dependencies") removed a
series of unnecessary dependencies on GPIOLIB when the gpio was
optional.
A similar simplification seems valid for nau8315, so remove the
dependency as well. This will avoid the following warning
WARNING: unmet direct dependencies detected for SND_SOC_NAU8315
Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] &&
GPIOLIB [=n]
Selected by [y]:
- SND_SOC_INTEL_SOF_NAU8825_MACH [=y] && SOUND [=y] && !UML &&
SND [=y] && SND_SOC [=y] && SND_SOC_INTEL_MACH [=y] &&
(SND_SOC_SOF_HDA_LINK [=y] || SND_SOC_SOF_BAYTRAIL [=n]) &&
I2C [=y] && ACPI [=y] && SND_HDA_CODEC_HDMI [=y] &&
SND_SOC_SOF_HDA_AUDIO_CODEC [=y] && (MFD_INTEL_LPSS [=n] ||
COMPILE_TEST [=y])
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230108114351.539786-1-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors when CONFIG_GPIOLIB is not enabled:
../sound/soc/codecs/tlv320adc3xxx.c: In function 'adc3xxx_i2c_probe':
../sound/soc/codecs/tlv320adc3xxx.c:1352:28: error: implicit declaration of function 'devm_gpiod_get'; did you mean 'devm_gpio_free'? [-Werror=implicit-function-declaration]
1352 | adc3xxx->rst_pin = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
../sound/soc/codecs/tlv320adc3xxx.c:1352:57: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
1352 | adc3xxx->rst_pin = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
CC lib/dynamic_debug.o
../sound/soc/codecs/tlv320adc3xxx.c:1400:9: error: implicit declaration of function 'gpiod_set_value_cansleep'; did you mean 'gpio_set_value_cansleep'? [-Werror=implicit-function-declaration]
1400 | gpiod_set_value_cansleep(adc3xxx->rst_pin, 1);
Fixes: e9a3b57efd ("ASoC: codec: tlv320adc3xxx: New codec driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Ricard Wanderlof <ricardw@axis.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Link: https://lore.kernel.org/r/20221006235822.30074-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_REGMAP_SLIMBUS is not set,
make ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-,
will be failed, like this:
sound/soc/codecs/wcd934x.o: In function `wcd934x_codec_probe':
wcd934x.c:(.text+0x3310): undefined reference to `__regmap_init_slimbus'
make: *** [vmlinux] Error 1
Add select REGMAP_SLIMBUS to config SND_SOC_WCD934X.
Fixes: a61f3b4f47 ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220926074042.13297-1-renzhijie2@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS42L83 part is a headphone jack codec found in recent Apple
machines. It is a publicly undocumented part but as far as can be told
it is identical to CS42L42 except for two points:
* The chip ID is different.
* Of those registers for which we have a default value in the existing
CS42L42 kernel driver, one register (MCLK_CTL) differs in its reset
value on CS42L83.
To address those two points (and only those), add to the CS42L42 driver
a separate CS42L83 front.
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220915094444.11434-10-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add generic ASoC equivalent of ALSA HD-Audio codec. This codec is
designed to follow HDA_DEV_LEGACY convention. Driver wrapps existing
hda_codec.c handlers to prevent code duplication within the newly added
code. Number of DAIs created is dependent on capabilities exposed by the
codec itself. Because of this, single solution can be applied to support
every single HD-Audio codec type.
At the same time, through the ASoC topology, platform drivers may limit
the number of endpoints available to the userspace as codec driver
exposes BE DAIs only.
Both hda_codec_probe() and hda_codec_remove() declare their expectations
on device's usage_count and suspended-status. This is to catch any
unexpected behavior as PM-related code for HD-Audio has been changing
quite a bit throughout the years.
In order for codec DAI list to reflect its actual PCM capabilities, PCMs
need to be built and that can only happen once codec device is
constructed. To do that, a valid component->card->snd_card pointer is
needed. Said pointer will be provided by the framework once all card
components are accounted for and their probing can begin. Usage of
"binder" BE DAI solves the problem - codec can be listed as one of
HD-Audio card components without declaring any actual BE DAIs
statically.
Relation with hdac_hda:
Addition of parallel solution is motivated by behavioral differences
between hdac_hda.c and its legacy equivalent found in sound/pci/hda
e.g.: lack of dynamic, based on codec capabilities, resource allocation
and high cost of removing such differences on actively used targets.
Major goal of codec driver presented here is to follow HD-Audio legacy
behavior in 1:1 fashion by becoming a wrapper. Doing so increases code
coverage of the legacy code and reduces the maintenance cost for both
solutions.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220511162403.3987658-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit dcc2c012c7 ("ASoC: Fix gpiolib dependencies") removed a
series of unnecessary dependencies on GPIOLIB when the gpio was
optional.
A similar simplification seems valid for max98357a, so remove the
dependency as well. This will avoid the following warning
WARNING: unmet direct dependencies detected for SND_SOC_MAX98357A
Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && GPIOLIB [=n]
Selected by [y]:
- SND_SOC_INTEL_SOF_CS42L42_MACH [=y] && SOUND [=y] && !UML &&
SND [=y] && SND_SOC [=y] && SND_SOC_INTEL_MACH [=y] &&
(SND_SOC_SOF_HDA_LINK [=y] || SND_SOC_SOF_BAYTRAIL [=n]) && I2C
[=y] && ACPI [=y] && SND_HDA_CODEC_HDMI [=y] &&
SND_SOC_SOF_HDA_AUDIO_CODEC [=y] && (MFD_INTEL_LPSS [=y] ||
COMPILE_TEST [=n])
Reported-by: kernel test robot <yujie.liu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220517172647.468244-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series of patches adds support for Analog Devices MAX98396
mono amplifier with IV sense. The device provides a PCM interface
for audio data and a standard I2C interface for control data
communication. This driver also supports MAX98397 which is
a variant of MAX98396 with wide input supply range.
Signed-off-by: Ryan Lee <ryan.lee.analog@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220423021558.1773598-1-ryan.lee.analog@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW8738 is a simple audio amplifier using a single GPIO.
The main difference to simple-amplifier is that there is a "one-wire
pulse control" that allows configuring the amplifier to one of a few
pre-defined modes. This can be used to configure the speaker-guard
function (primarily the power limit for the amplifier).
Add a simple driver that allows setting it up in the device tree
with a specified mode number.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220304102452.26856-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Mark Brown <broonie@kernel.org>:
This series removes a bunch of spurious selects of gpiolib that were
causing noise in randconfig build tests.
Mark Brown (6):
ASoC: dmic: Remove spurious gpiolib select
ASoC: rt9120: Remove spurious gpiolib select
ASoC: simple-amplifier: Remove spurious gpiolib select
ASoC: max9759: Remove spurious gpiolib select
ASoC: zl38060: Remove spurious gpiolib select
ASoC: simple-mux: Depend on gpiolib rather than selecting it
sound/soc/codecs/Kconfig | 8 ++------
1 file changed, 2 insertions(+), 6 deletions(-)
base-commit: e783362eb5
--
2.30.2
The simple-mux driver requires gpiolib. Currently it selects GPIOLIB but
since the use of select can lead to issues with randconfig let's instead
depend on GPIOLIB, select is more idiomatically used for Kconfig symbols
that are not user selectable but GPIOLIB is user selectable.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220202192333.3655269-7-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Madera CODECs use regmap_irq functions but nothing ensures that
regmap_irq is built into the kernel. Add dependencies on the ASoC
symbols for the relevant MFD component. There is no point in building
the ASoC driver if the MFD doesn't support it and the MFD part contains
the necessary dependencies to ensure everything is built into the
kernel.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220203115025.16464-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To support CS35L41 in HDA systems the HDA driver
for CS35L41 would have to duplicate some functions
that already exist on ASoC driver
So instead of duplicate the code, use the new lib
source as a shared resource for both ASoC and HDA
Also, change the way CONFIG_SND_SOC_CS35L41 is
selected, as reported by Intel Kernel test robot,
it is possible to build SND_SOC_CS35L41_SPI/I2C
without the main driver, which would lead to build
failures.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211217115708.882525-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 0454422288 ("ASoC: codecs: wcd938x: add audio routing and
Kconfig") adds SND_SOC_WCD937X, which does not exist, and
SND_SOC_WCD938X, which seems not really to be the intended config to be
selected, but only a supporting config symbol to the actual config
SND_SOC_WCD938X_SDW for the codec.
Add SND_SOC_WCD938_SDW to the list instead of SND_SOC_WCD93{7,8}X.
The issue was identified with ./scripts/checkkconfigsymbols.py.
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211125095158.8394-3-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This drops the rt9210 support due to a race with a new version being
sent out for some incremental changes.
Signed-off-by: Mark Brown <broonie@kernel.org>
