For this bug, there are two capture pcm streams active, with one
stream and its related stream tag released before suspend. Later
when system suspend is done, the stream tag for the remaining
active stream is released by SOF driver. After system resume, hda
codec driver restores the stream tag for the active pcm stream,
but SOF goes to assign a new one, which now doesn't match with the
stream tag used by codec driver, and this causes DMA to fail
receiving data, leading to unrecoverable XRUN condition in FW.
For stream tag is stored in both hda codec and SOF driver, it
shouldn't be released only in SOF driver. This patch just keeps the
stream information in dma data and checks whether there is a stored
DMA data for stream resuming from S3 and restores it. And it also
removes DMA data when the stream is released.
Tested on Whiskey Lake platform.
GitHub issue: https://github.com/thesofproject/sof/issues/1594
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7d4f606c50 ("ALSA: hda - WAKEEN feature enabling for
runtime pm"), legacy HD-A driver sets hda controller in reset mode after
entering runtime-suspend. And when resuming from suspend mode, it checks
hda controller & codec status to detect headphone hotplug event. Now
this patch does the same job in SOF runtime pm functions.
And we need to check all the non-hdmi codecs for some cases like playback
with HDMI or capture with DMIC connected to dsp. In these cases, only
controller is active and codecs are suspended, so codecs can't send
unsolicited event to controller. The jack polling operation will activate
codecs and unsolicited event can work even codecs become suspended later.
Tested on whiskylake with hda codecs.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
FW encapsulates information about section types (e.g DRAM, IRAM)
inside module block header. This information can be used in order
to correctly load the section to the appropriate place in memory.
SOF Linux driver needs to know for each platform how to map the
section type with the corresponding memory BAR. So, this patch
introduces get_bar_index, a new operation inside snd_sof_dsp_ops.
Intel platforms, usually load all the section in a contiguous memory
area (usually denoted by sdev->mmio_bar) so things are relatively
simple there. Anyhow, on i.MX8 IRAM and DRAM for example are mapped
to distinct BARs.
By default, if no get_bar function is provided the core implementation
will always return sdev->mmio_bar so that there will be no need for
a change to existing Intel code.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When application goes through SUSPEND/STOP->PREPARE->START
cycle, we should always reprogram the SOF device to start
DMA from a known state so that hw_ptr/appl_ptrs remain valid.
This is expected by ALSA core as it resets the buffer
state as part of prepare (see snd_pcm_do_prepare()).
Fix the issue by forcing reconfiguration of the FW with
STREAM_PCM_PARAMS in prepare(). Use combined logic to handle
prepare and the existing flow to reprogram hw-params after
system suspend.
Without the fix, first call to pcm pointer() will return
an invalid hw_ptr and application may immediately observe XRUN
status, unless "start_threshold" SW parameter is set to maximum
value by the application.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_hdac_ext_bus_device_exit() has been recently modified
to no longer free the hdac device. SOF allocates memory for
hdac_device and hda_hda_priv with kzalloc. Make them
device-managed instead so that they will be freed when the
SOF driver is unloaded.
Because of the above change, hda_codec is device-managed and
it will be freed when the ASoC device is removed. Freeing
the codec in snd_hda_codec_dev_release() leads to kernel
panic while unloading and reloading the ASoC driver. So,
avoid freeing the hda_codec for ASoC driver. This is done in
the same patch to avoid bisect failure.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20190626070450.7229-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This back-merge is necessary for adjusting the latest FireWire fix
with the recent refactoring in 5.3 development branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compile-testing without PCI just causes warnings:
sound/soc/sof/sof-pci-dev.c:330:13: error: 'sof_pci_remove' defined but not used [-Werror=unused-function]
static void sof_pci_remove(struct pci_dev *pci)
^~~~~~~~~~~~~~
sound/soc/sof/sof-pci-dev.c:230:12: error: 'sof_pci_probe' defined but not used [-Werror=unused-function]
static int sof_pci_probe(struct pci_dev *pci,
^~~~~~~~~~~~~
I tried to fix this in a way that would still allow compile
tests, but it got too ugly, so this just reverts the patch
that allowed it in the first place.
Most architectures do allow enabling PCI, so the value of the
COMPILE_TEST alternative was not very high to start with.
Fixes: e13ef82a9a ("ASoC: SOF: add COMPILE_TEST for PCI options")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per the HW recommendation, after setting the RUN bit
(start as 1, stop as 0), software must read the bit back
to make sure the bit is set right, before modifying related
control registers/re-starting the DMA engine.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stream status and WAKESTS registers need to be cleared by writing
to them with snd_sof_dsp_write(). snd_sof_dsp_update_bits() only
writes if the value is changed and will result in not clearing
the status.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add common hda_dsp_ctrl_stop_chip() function to stop controller with
the same function handling both HDA and non-HDA cases. This function
disables IRQs and clears status masks. When CONFIG_SND_SOC_SOF_HDA
is defined, also disables the CORB/RIRB, and stops i/o.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should use irq disabled mode when read/write hda registers from
thread context, as we need to hold the same bus->reg_lock in interrupt
context hda_dsp_stream_interrupt(), otherwise, when we are holding the
lock in hda_dsp_stream_hw_free() and the interrupt arrives, we will get
deadlock in the interrupt handler.
Error logs like this:
[ 5.603606] CPU0
[ 5.603606] ----
[ 5.603607] lock(&(&bus->reg_lock)->rlock);
[ 5.603608] <Interrupt>
[ 5.603609] lock(&(&bus->reg_lock)->rlock);
[ 5.603610]
*** DEADLOCK ***
[ 5.603611] 2 locks held by pulseaudio/2329:
[ 5.603612] #0: 000000005fcf26c6 (&card->mutex/1){+.+.}, at: dpcm_fe_dai_hw_free+0x2b/0x110 [snd_soc_core]
[ 5.603619] #1: 00000000ef369faf (&rtd->pcm_mutex){+.+.}, at: soc_pcm_hw_free+0x2e/0x1c0 [snd_soc_core]
The fix is simple, let's switch to use spin_lock/unlock_irq().
Reported-by: Xun Zhang <xun2.zhang@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the stream interrupt handler to always wake up the
IRQ thread if the status register is valid. The IRQ thread
performs the check for stream interrupts and RIRB interrupts
in a loop to handle the case of missed interrupts when an
unsolicited response from the codec is received just before the
stream interrupt handler is completed.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Paused streams do not get suspended when the system enters S3.
So, clear and release link DMA channel for such streams in the
hda_dsp_set_hw_params_upon_resume() callback. Also, invalidate
the link DMA channel in the DAI config before restoring the
dai config upon resume. Also, modify the signature for the
set_hw_params_upon_resume() op to return an int.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the HW programming sequence requirement that the host
and link DMA channels need to be coupled/decoupled during pcm
hw_params, the host DMA channel corresponding to the link
DMA channel in use for hostless streams needs to be reserved.
This is achieved by adding a host_reserved flag in the
sof_intel_hda_stream structure which is checked when assigning
a host DMA channel.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recommended HDA HW programming sequence for setting
the DMA format requires that the link DMA and host DMA
channels be coupled before setting the format. This
change means that host DMA or link DMA channels be
reserved even if only one is used.
Statically assigned link DMA channels would mean that
all the corresponding host DMA channels will need to be
reserved, leaving only a few channels available at run-time.
So, the suggestion here is to switch to dynamically assigning
both host DMA channels and link DMA channels are run-time.
The host DMA channel is assigned when the pcm
is opened as before. While choosing the link DMA channel,
if the host DMA channel corresponding to the link DMA channel
is already taken, the proposed method checks to make
sure that the BE is connected to the FE that has been assigned
this host DMA channel. Once the link DMA channel is assigned,
an IPC is sent to the DSP to set the link DMA channel.
The link DMA channel is freed during hw_free() and also in the
SUSPEND trigger callback. It will be re-assigned when hw_params
are set upon resume.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the cpu_dai_name member to snd_sof_dai and save the
cpu_dai_name while setting the DAI config.
The internal SOF representation will have to change at a later point
as well when we have multiple CPU dais.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull sound fixes from Takashi Iwai:
"It might feel like deja vu to receive a bulk of changes at rc5, and it
happens again; we've got a collection of fixes for ASoC. Most of fixes
are targeted for the newly merged SOF (Sound Open Firmware) stuff and
the relevant fixes for Intel platforms.
Other than that, there are a few regression fixes for the recent ASoC
core changes and HD-audio quirk, as well as a couple of FireWire fixes
and for other ASoC codecs"
* tag 'sound-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
Revert "ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops"
ALSA: ice1712: Check correct return value to snd_i2c_sendbytes (EWS/DMX 6Fire)
ALSA: oxfw: allow PCM capture for Stanton SCS.1m
ALSA: firewire-motu: fix destruction of data for isochronous resources
ASoC: Intel: sst: fix kmalloc call with wrong flags
ASoC: core: Fix deadlock in snd_soc_instantiate_card()
SoC: rt274: Fix internal jack assignment in set_jack callback
ALSA: hdac: fix memory release for SST and SOF drivers
ASoC: SOF: Intel: hda: use the defined ppcap functions
ASoC: core: move DAI pre-links initiation to snd_soc_instantiate_card
ASoC: Intel: cht_bsw_rt5672: fix kernel oops with platform_name override
ASoC: Intel: cht_bsw_nau8824: fix kernel oops with platform_name override
ASoC: Intel: bytcht_es8316: fix kernel oops with platform_name override
ASoC: Intel: cht_bsw_max98090: fix kernel oops with platform_name override
ASoC: sun4i-i2s: Add offset to RX channel select
ASoC: sun4i-i2s: Fix sun8i tx channel offset mask
ASoC: max98090: remove 24-bit format support if RJ is 0
ASoC: da7219: Fix build error without CONFIG_I2C
ASoC: SOF: Intel: hda: Fix COMPILE_TEST build error
ASoC: SOF: fix DSP oops definitions in FW ABI
...
Always get kcontrol value from cache, set kcontrol value to DSP
when DSP is active. Kcontrol values will be restored when DSP boot up.
We will set the default value of kcontrol in sof_complete to make sure
the value is align with firmware.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The settling time of DMIC DC level is both platform and used
microphone model specific. The unmute gain ramp is used to conceal
most of the large DC level seen in beginning of capture. This patch
adds into the DMIC DAI IPC struct a new field called unmute_ramp_time
and a new token SOF_TKN_INTEL_DMIC_UNMUTE_RAMP_TIME. The value is the
ramp length in milliseconds (ms).
The ABI minor version is incremented for this backwards compatible
change.
Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently passes the volume ramp type and length
topology tokens to firmware, but the min and max volume are
not set. This patch provides a correction to convert the
information from the topology file and pass the linear volume
min/max value to the firmware to improve transitions.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
