Kernel version for new ABI in 4.0 has been documented
as 3.20, since the changes have been merged before the kernel
version number change.
Change kernel version from 3.20 to 4.0.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some devices have hardware buffers that can store a number of samples
for later consumption. Hardware usually provides interrupts to notify
the processor when the FIFO is full or when it has reached a certain
watermark level. This helps with reducing the number of interrupts to
the host processor and thus it helps decreasing the power consumption.
This patch enables usage of hardware FIFOs for IIO devices in
conjunction with software device buffers. When the hardware FIFO is
enabled the samples are stored in the hardware FIFO. The samples are
later flushed to the device software buffer when the number of entries
in the hardware FIFO reaches the hardware watermark or when a flush
operation is triggered by the user when doing a non-blocking read
on an empty software device buffer.
In order to implement hardware FIFO support the device drivers must
implement the following new operations: setting and getting the
hardware FIFO watermark level, flushing the hardware FIFO to the
software device buffer. The device must also expose information about
the hardware FIFO such it's minimum and maximum watermark and if
necessary a list of supported watermark values. Finally, the device
driver must activate the hardware FIFO when the device buffer is
enabled, if the current device settings allows it.
The software device buffer watermark is passed by the IIO core to the
device driver as a hint for the hardware FIFO watermark. The device
driver can adjust this value to allow for hardware limitations (such
as capping it to the maximum hardware watermark or adjust it to a
value that is supported by the hardware). It can also disable the
hardware watermark (and implicitly the hardware FIFO) it this value is
below the minimum hardware watermark.
Since a driver may support hardware FIFO only when not in triggered
buffer mode (due to different semantics of hardware FIFO sampling and
triggered sampling) this patch changes the IIO core code to allow
falling back to non-triggered buffered mode if no trigger is enabled.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the IIO buffer blocking read only wait until at least one
data element is available.
This patch makes the reader sleep until enough data is collected before
returning to userspace. This should limit the read() calls count when
trying to get data in batches.
Co-author: Yannick Bedhomme <yannick.bedhomme@mobile-devices.fr>
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
[rebased and remove buffer timeout]
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds ABI documentation entries for in_rot_offset.
At least one user for these is present that is the HID Sensors Driver.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patchset adds ABI documentation for the following attributes:
in_illuminance_scale, used atleast once in al3320a staging/iio/light/
in_illuminance_calibscale, used atleast once in cm32181
in_illuminance_input, used in cm3232 at least once
in_illuminance_raw used atleast once in al3320a
in_illuminance_clear_raw and in_illuminance_ir_raw exposed by
gp2ap020a00f with modifiers IIO_MOD_LIGHT_CLEAR and
IIO_MOD_LIGHT_IR respectively.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the attribute name of the configuration record class ID.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Jonathan writes:
First set of new drivers, cleanups and functionality for IIO in the 4.1 cycle.
New drivers
* CM3323 color sensor.
* MS5611 pressure and temperature sensor.
New functionality
* mup6050 - create mux clients for devices described via ACPI. The reasoning
and approach taken in this patch are complex. Basically there is no
otherway of finding out what is there than by some esoteric look ups in
the ACPI data.
* cm3232 - PM support
* itg3200 - suspend/resume support
* mcp320x - add more ADCs to the kconfig to reflect what the driver supports
(this patch and the bindings got left behind when the support was added
a while back).
Docs / utils
* ti-adc128s052 - DT bindings.
* mcp3422 - DT bindings.
* mcp320x - DT bindings
* ABI docs for event threshold scale attributes, in_magn_offset, proximity
scan_element and thresh falling/rising values for accelerometers. All
elements long in use that have slipped by being explicitly documented.
* Tidy up the tools previously in drivers/staging/iio/Documentation and move
them out to /tools/iio. Yet another move that should have happened long ago.
This time Roberta Dobrescu did the leg work. Thanks!
Core Cleanups
* Export userspace IIO headers. We should have done the appropriate header
splitting a long time ago. Thanks to Daniel for sorting this out.
* Refactor the registring of attributes for buffers to move all non-custom
ones to a vector allowing easier additions to the current set in the future.
Driver Cleanups
* gpiod related cleanups. Make use of the additional parameter to specify
initial direciton to avoid extra code.
* bmc150 - Various refactorings to reduce code repitition and prepare for
hardware buffer support. Some of these cleanups are good even
without the new functionality.
* kmx61 - direct use of index to an array avoiding a structure element which
was always the index to an element in an array of that structure.
* vf610 - avoid incorrect type for return from wait_for_completion_timeout.
* gp2ap020a00f - use put_unaligned_le32 for slight code simplification.
* ade7754 - improve error handling including suppressing some build warnings.
* ade7759 - improve error handling including suppressing some build warnings.
* hmc5843 - Long line and indentation fixes. Also some constifying of various
constant data.
* ade7854 - 80+ character line splitting.
* ad2s1210 - fix wrong printf format string.
* mxs-lradc - fix wrong printf format string.
* ade7954-i2c - code alignment fixes and other trivial but worthwhile bits.
* periodic rtc trigger - make the frequency type an unsigned int as it
is always treated as such.
* jsa1212 - constify struct regmap_config as it is constant.
* ad7793 - typo in the MODULE_DESCRIPTION
* mma9551 - check gpiod_to_irq errors. Note that this doesn't actually cause
any trouble but is worth tidying up as obviously incorrect.
* mlx90614 - refactor the register symbols to make it clear which reads are to
RAM not PROM.
Similar to port id allow netdevices to specify port names and export
the name via sysfs. Drivers can implement the netdevice operation to
assist udev in having sane default names for the devices using the
rule:
$ cat /etc/udev/rules.d/80-net-setup-link.rules
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_port_name}!="",
NAME="$attr{phys_port_name}"
Use of phys_name versus phys_id was suggested-by Jiri Pirko.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a tx_maxrate attribute to the tx queue sysfs entry allowing
for max-rate limiting. Along with DCB-ETS and BQL this provides another
knob to tune queue performance. The limit units are Mbps.
By default it is disabled. To disable the rate limitation after it
has been set for a queue, it should be set to zero.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ABI documentation entries for
in_accel_thresh_falling_value, and in_accel_thresh_rising_value in /events.
There is at least one user for these, lis3l02dq in accel.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds ABI documentation entries for in_proximity_en,
in_proximity_type, and in_proximity_index in the scan_elements directory.
At least one user for these is present, the AS3935 Franklin lightning sensor.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds ABI documentation entries for in_magn_offset.
There is one user, hid-sensor-magn-3d in drivers/iio/magnetometer.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for configfs interface so that f_printer can be used as a
component of usb gadgets composed with it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit exposes in sysfs the HID country code that is stored in the country
member of hid_device structure. It identifies the country code of localized
hardware.
For example some keyboards use it to exhibit the language of the key layout. It
helps the upper layer to identify the localized hardware and setup the correct
language to use.
For USB HID devices the country code comes for the HID descriptor and for
Bluetooth HID devices it is the HIDCountryCode attribute from the SDP database.
Signed-off-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull platform driver update from Darren Hart:
"This includes a significant update to the toshiba_acpi driver,
bringing it to feature parity with the Windows driver, followed by
some needed cleanups.
The other changes are mostly minor updates, quirks, sparse fixes, or
cleanups.
Details:
- toshiba_acpi:
Add support for missing features from the Windows driver, bump the
sysfs version, and clean up the driver.
- thinkpad_acpi:
BIOS string versions, unhandled hkey events.
- msamsung-laptop:
Add native backlight quirk, enable better lid handling.
- intel_scu_ipc:
Read resources from PCI configuration
- other:
Fix sparse warnings, general cleanups"
* tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (34 commits)
toshiba_acpi: Cleanup GPL header
toshiba_acpi: Cleanup comment blocks and capitalization
toshiba_acpi: Make use of DEVICE_ATTR_{RO, RW} macros
toshiba_acpi: Drop the toshiba_ prefix from sysfs function names
toshiba_acpi: Move sysfs function and struct declarations further down
Documentation/ABI: Add file describing the sysfs entries for toshiba_acpi
toshiba_acpi: Clean file according to coding style
toshiba_acpi: Bump version number to 0.21
toshiba_acpi: Add support to enable/disable USB 3
toshiba_acpi: Add support for Panel Power ON
toshiba_acpi: Add support for Keyboard functions mode
toshiba_acpi: Add fan entry to sysfs
toshiba_acpi: Add version entry to sysfs
thinkpad_acpi: support new BIOS version string pattern
thinkpad_acpi: unhandled hkey event
toshiba_acpi: Make toshiba_eco_mode_available more robust
classmate-laptop: Fix sparse warning (0 as NULL)
Sony-laptop: Fix sparse warning (make undeclared var static)
thinkpad_acpi.c: Fix sparse warning (make undeclared var static)
samsung-laptop.c: Prefer kstrtoint over single variable sscanf
...
Allow switching of Logitech gaming wheels between available compatibility modes
through sysfs. This only applies to multimode wheels.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Display the real wheel model and supported alternate modes through sysfs. This
applies only to multimode wheels.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull staging drivers patches from Greg KH:
"Here's the big staging driver tree update for 3.20-rc1.
Lots of little things in here, adding up to lots of overall cleanups.
The IIO driver updates are also in here as they cross the staging tree
boundry a lot. I2O has moved into staging as well, as a plan to drop
it from the tree eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a
while"
* tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (740 commits)
staging: lustre: lustre: libcfs: define symbols as static
staging: rtl8712: Do coding style cleanup
staging: lustre: make obd_updatemax_lock static
staging: rtl8188eu: core: switch with redundant cases
staging: rtl8188eu: odm: conditional setting with no effect
staging: rtl8188eu: odm: condition with no effect
staging: ft1000: fix braces warning
staging: sm7xxfb: fix remaining CamelCase
staging: sm7xxfb: fix CamelCase
staging: rtl8723au: multiple condition with no effect - if identical to else
staging: sm7xxfb: make smtc_scr_info static
staging/lustre/mdc: Initialize req in mdc_enqueue for !it case
staging/lustre/clio: Do not allow group locks with gid 0
staging/lustre/llite: don't add to page cache upon failure
staging/lustre/llite: Add exception entry check after radix_tree
staging/lustre/libcfs: protect kkuc_groups from write access
staging/lustre/fld: refer to MDT0 for fld lookup in some cases
staging/lustre/llite: Solve a race to access lli_has_smd in read case
staging/lustre/ptlrpc: hold rq_lock when modify rq_flags
staging/lustre/lnet: portal spreading rotor should be unsigned
...
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
Pull f2fs updates from Jaegeuk Kim:
"Major changes are to:
- add f2fs_io_tracer and F2FS_IOC_GETVERSION
- fix wrong acl assignment from parent
- fix accessing wrong data blocks
- fix wrong condition check for f2fs_sync_fs
- align start block address for direct_io
- add and refactor the readahead flows of FS metadata
- refactor atomic and volatile write policies
But most of patches are for clean-ups and minor bug fixes. Some of
them refactor old code too"
* tag 'for-f2fs-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (64 commits)
f2fs: use spinlock for segmap_lock instead of rwlock
f2fs: fix accessing wrong indexed data blocks
f2fs: avoid variable length array
f2fs: fix sparse warnings
f2fs: allocate data blocks in advance for f2fs_direct_IO
f2fs: introduce macros to convert bytes and blocks in f2fs
f2fs: call set_buffer_new for get_block
f2fs: check node page contents all the time
f2fs: avoid data offset overflow when lseeking huge file
f2fs: fix to use highmem for pages of newly created directory
f2fs: introduce a batched trim
f2fs: merge {invalidate,release}page for meta/node/data pages
f2fs: show the number of writeback pages in stat
f2fs: keep PagePrivate during releasepage
f2fs: should fail mount when trying to recover data on read-only dev
f2fs: split UMOUNT and FASTBOOT flags
f2fs: avoid write_checkpoint if f2fs is mounted readonly
f2fs: support norecovery mount option
f2fs: fix not to drop mount options when retrying fill_super
f2fs: merge flags in struct f2fs_sb_info
...
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
This patch adds a new file describing the sysfs entries for the
toshiba_acpi driver.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull powerpc updates from Michael Ellerman:
- Update of all defconfigs
- Addition of a bunch of config options to modernise our defconfigs
- Some PS3 updates from Geoff
- Optimised memcmp for 64 bit from Anton
- Fix for kprobes that allows 'perf probe' to work from Naveen
- Several cxl updates from Ian & Ryan
- Expanded support for the '24x7' PMU from Cody & Sukadev
- Freescale updates from Scott:
"Highlights include 8xx optimizations, some more work on datapath
device tree content, e300 machine check support, t1040 corenet
error reporting, and various cleanups and fixes"
* tag 'powerpc-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (102 commits)
cxl: Add missing return statement after handling AFU errror
cxl: Fail AFU initialisation if an invalid configuration record is found
cxl: Export optional AFU configuration record in sysfs
powerpc/mm: Warn on flushing tlb page in kernel context
powerpc/powernv: Add OPAL soft-poweroff routine
powerpc/perf/hv-24x7: Document sysfs event description entries
powerpc/perf/hv-gpci: add the remaining gpci requests
powerpc/perf/{hv-gpci, hv-common}: generate requests with counters annotated
powerpc/perf/hv-24x7: parse catalog and populate sysfs with events
perf: define EVENT_DEFINE_RANGE_FORMAT_LITE helper
perf: add PMU_EVENT_ATTR_STRING() helper
perf: provide sysfs_show for struct perf_pmu_events_attr
powerpc/kernel: Avoid initializing device-tree pointer twice
powerpc: Remove old compile time disabled syscall tracing code
powerpc/kernel: Make syscall_exit a local label
cxl: Fix device_node reference counting
powerpc/mm: bail out early when flushing TLB page
powerpc: defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
perf/powerpc: reset event hw state when adding it to the PMU
powerpc/qe: Use strlcpy()
...
This patch introduces a batched trimming feature, which submits split discard
commands.
This is to avoid long latency due to huge trim commands.
If fstrim was triggered ranging from 0 to the end of device, we should lock
all the checkpoint-related mutexes, resulting in very long latency.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
A few new drivers (power button handler for AXP20x PMIC, tps65218
power button driver, sun4i keys driver, regulator haptic driver, NI
Ettus Research USRP E3x0 button, Alwinner A10/A20 PS/2 controller).
Updates to Synaptics and ALPS touchpad drivers (with more to come
later), brand new Focaltech PS/2 support, update to Cypress driver to
handle Gen5 (in addition to Gen3) devices, and number of other fixups
to various drivers as well as input core"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: elan_i2c - fix wrong %p extension
Input: evdev - do not queue SYN_DROPPED if queue is empty
Input: gscps2 - fix MODULE_DEVICE_TABLE invocation
Input: synaptics - use dmax in input_mt_assign_slots
Input: pxa27x_keypad - remove unnecessary ARM includes
Input: ti_am335x_tsc - replace delta filtering with median filtering
ARM: dts: AM335x: Make charge delay a DT parameter for TSC
Input: ti_am335x_tsc - read charge delay from DT
Input: ti_am335x_tsc - remove udelay in interrupt handler
Input: ti_am335x_tsc - interchange touchscreen and ADC steps
Input: MT - add support for balanced slot assignment
Input: drv2667 - remove wrong and unneeded drv2667-haptics modalias
Input: drv260x - remove wrong and unneeded drv260x-haptics modalias
Input: cap11xx - remove wrong and unneeded cap11xx modalias
Input: sun4i-ts - add support for touchpanel controller on A31
Input: serio - add support for Alwinner A10/A20 PS/2 controller
Input: gtco - use sign_extend32() for sign extension
Input: elan_i2c - verify firmware signature applying it
Input: elantech - remove stale comment from Kconfig
Input: cyapa - off by one in cyapa_update_fw_store()
...
Pull power supply and reset changes from Sebastian Reichel:
"New drivers:
- charger driver for Maxim 77693
- battery gauge driver for LTC 2941/2943
- battery gauge driver for RT5033
- reset driver for R-Mobile platforms
Convert drivers to restart handler framework:
- arm-versatile
- at91
- st-poweroff
Misc:
- remove deprecated sun6i reboot driver
- use alarmtimer instead of rtc in charger-manager
- misc fixes"
* tag 'for-v3.20' of git://git.infradead.org/battery-2.6: (48 commits)
power_supply: 88pm860x: Fix leaked power supply on probe fail
power/reset: restart-poweroff: Remove arm dependencies
power/reset: st-poweroff: Fix misleading Kconfig description
power/reset: st-poweroff: Register with kernel restart handler
power/reset: Remove sun6i reboot driver
power/reset: at91: Register with kernel restart handler
power/reset: arm-versatile: Register with kernel restart handler
power: test_power: Use enum as index for array of supplies
Add devicetree binding documentation for the LTC2941/LTC2943 driver
Add LTC2941/LTC2943 Battery Gauge Driver
power/reset: brcmstb: Add support for old 65nm chips
power/reset: brcmstb: Use the DT "compatible" string to indicate bit positions
power/reset: brcmstb: Make the driver buildable on MIPS
power: charger-manager: Use alarmtimer for battery monitoring in suspend.
power/reset: at91-poweroff: Fix error handling and other compiler warnings
bq27x00_battery: Call power_supply_changed only when capacity changed
bq27x00_battery: fix register offset for bq27425
power: max14577: Remove SYSFS dependency from Kconfig
power: bq24190_charger: suppress build warning
power: reset: Add reset driver for R-Mobile platforms
...
Pull live patching infrastructure from Jiri Kosina:
"Let me provide a bit of history first, before describing what is in
this pile.
Originally, there was kSplice as a standalone project that implemented
stop_machine()-based patching for the linux kernel. This project got
later acquired, and the current owner is providing live patching as a
proprietary service, without any intentions to have their
implementation merged.
Then, due to rising user/customer demand, both Red Hat and SUSE
started working on their own implementation (not knowing about each
other), and announced first versions roughly at the same time [1] [2].
The principle difference between the two solutions is how they are
making sure that the patching is performed in a consistent way when it
comes to different execution threads with respect to the semantic
nature of the change that is being introduced.
In a nutshell, kPatch is issuing stop_machine(), then looking at
stacks of all existing processess, and if it decides that the system
is in a state that can be patched safely, it proceeds insterting code
redirection machinery to the patched functions.
On the other hand, kGraft provides a per-thread consistency during one
single pass of a process through the kernel and performs a lazy
contignuous migration of threads from "unpatched" universe to the
"patched" one at safe checkpoints.
If interested in a more detailed discussion about the consistency
models and its possible combinations, please see the thread that
evolved around [3].
It pretty quickly became obvious to the interested parties that it's
absolutely impractical in this case to have several isolated solutions
for one task to co-exist in the kernel. During a dedicated Live
Kernel Patching track at LPC in Dusseldorf, all the interested parties
sat together and came up with a joint aproach that would work for both
distro vendors. Steven Rostedt took notes [4] from this meeting.
And the foundation for that aproach is what's present in this pull
request.
It provides a basic infrastructure for function "live patching" (i.e.
code redirection), including API for kernel modules containing the
actual patches, and API/ABI for userspace to be able to operate on the
patches (look up what patches are applied, enable/disable them, etc).
It's relatively simple and minimalistic, as it's making use of
existing kernel infrastructure (namely ftrace) as much as possible.
It's also self-contained, in a sense that it doesn't hook itself in
any other kernel subsystem (it doesn't even touch any other code).
It's now implemented for x86 only as a reference architecture, but
support for powerpc, s390 and arm is already in the works (adding
arch-specific support basically boils down to teaching ftrace about
regs-saving).
Once this common infrastructure gets merged, both Red Hat and SUSE
have agreed to immediately start porting their current solutions on
top of this, abandoning their out-of-tree code. The plan basically is
that each patch will be marked by flag(s) that would indicate which
consistency model it is willing to use (again, the details have been
sketched out already in the thread at [3]).
Before this happens, the current codebase can be used to patch a large
group of secruity/stability problems the patches for which are not too
complex (in a sense that they don't introduce non-trivial change of
function's return value semantics, they don't change layout of data
structures, etc) -- this corresponds to LEAVE_FUNCTION &&
SWITCH_FUNCTION semantics described at [3].
This tree has been in linux-next since December.
[1] https://lkml.org/lkml/2014/4/30/477
[2] https://lkml.org/lkml/2014/7/14/857
[3] https://lkml.org/lkml/2014/11/7/354
[4] http://linuxplumbersconf.org/2014/wp-content/uploads/2014/10/LPC2014_LivePatching.txt
[ The core code is introduced by the three commits authored by Seth
Jennings, which got a lot of changes incorporated during numerous
respins and reviews of the initial implementation. All the followup
commits have materialized only after public tree has been created,
so they were not folded into initial three commits so that the
public tree doesn't get rebased ]"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: add missing newline to error message
livepatch: rename config to CONFIG_LIVEPATCH
livepatch: fix uninitialized return value
livepatch: support for repatching a function
livepatch: enforce patch stacking semantics
livepatch: change ARCH_HAVE_LIVE_PATCHING to HAVE_LIVE_PATCHING
livepatch: fix deferred module patching order
livepatch: handle ancient compilers with more grace
livepatch: kconfig: use bool instead of boolean
livepatch: samples: fix usage example comments
livepatch: MAINTAINERS: add git tree location
livepatch: use FTRACE_OPS_FL_IPMODIFY
livepatch: move x86 specific ftrace handler code to arch/x86
livepatch: samples: add sample live patching module
livepatch: kernel: add support for live patching
livepatch: kernel: add TAINT_LIVEPATCH
Some Samsung laptops with SABI3 delay the sleep for 10 seconds after
the lid is closed and do not wake up from sleep after the lid is opened.
A SABI command is needed to enable the better behavior.
Command = 0x6e, d0 = 0x81 enables this behavior. Returns d0 = 0x01.
Command = 0x6e, d0 = 0x80 disables this behavior. Returns d0 = 0x00.
Command = 0x6d and any d0 queries the state. This returns:
d0 = 0x00000*01, d1 = 0x00, d2 = 0x00, d3 = 0x0* when it is enabled.
d0 = 0x00000*00, d1 = 0x00, d2 = 0x00, d3 = 0x0* when it is disabled.
Where * is 0 - laptop has never slept or hibernated after switch on,
1 - laptop has hibernated just before,
2 - laptop has slept just before.
Patch addresses bug https://bugzilla.kernel.org/show_bug.cgi?id=75901 .
It adds a sysfs attribute lid_handling with a description and also an
addition to the quirks structure to enable the mode by default.
A user with another laptop in the bug report says that "power button has
to be pressed twice to wake the machine" when he or she enabled the mode
manually using the SABI command. Therefore, it is enabled by default
only for the single laptop that I have tested.
Signed-off-by: Julijonas Kikutis <julijonas.kikutis@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
An AFU may optionally contain one or more PCIe like configuration
records, which can be used to identify the AFU.
This patch adds support for exposing the raw config space and the
vendor, device and class code under sysfs. These will appear in a
subdirectory of the AFU device corresponding with the configuration
record number, e.g.
cat /sys/class/cxl/afu0.0/cr0/vendor
0x1014
cat /sys/class/cxl/afu0.0/cr0/device
0x4350
cat /sys/class/cxl/afu0.0/cr0/class
0x120000
hexdump -C /sys/class/cxl/afu0.0/cr0/config
00000000 14 10 50 43 00 00 00 00 06 00 00 12 00 00 00 00 |..PC............|
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00000100
These files behave in much the same way as the equivalent files for PCI
devices, with one exception being that the config file is currently
read-only and restricted to the root user. It is not necessarily
required to be this strict, but we currently do not have a compelling
use-case to make it writable and/or world-readable, so I erred on the
side of being restrictive.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for Freescale MMA9553L Intelligent Pedometer Platform.
The following functionalities are supported:
- step counter (counts the number of steps using a HW register)
- step detector (generates an iio event at every step the user takes)
- activity recognition (rest, walking, jogging, running)
- speed
- calories
- distance
To get accurate pedometer results, the user's height, weight and gender
need to be configured.
The specifications can be downloaded from:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA955xLSWRM.pdfhttp://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change calibheight unit from centimeters to meters
to follow iio guidelines of using SI units.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The pedometer needs to filter out false steps that might be generated by
tapping the foot, sitting, etc. To do that it computes the number of
steps that occur in a given time and decides the user is moving only
if this value is over a threshold. E.g.: the user starts moving only
if he takes 4 steps in 3 seconds. This filter is applied only when
the user starts moving.
A device that has such pedometer functionality is Freescale's MMA9553L:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf.
To export this feature, this patch introduces IIO_CHAN_INFO_DEBOUNCE_COUNT
and IIO_CHAN_INFO_DEBOUNCE_TIME. For the pedometer, in_steps_debounce_count
will specify the number of steps that need to occur in
in_steps_debounce_time seconds so that the pedometer decides the user is
moving.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
"
User visible changes:
- Enable sampling loads and stores simultaneously in 'perf mem' (Stephane Eranian)
- 'perf diff' output improvements (Namhyung Kim)
- Fix error reporting for evsel pgfault constructor (Arnaldo Carvalho de Melo)
Infrastructure changes:
- Move debugfs sterrno like method to tools/lib/ so that it may be used by
other tools, as 'perf probe' will be soon (Arnaldo Carvalho de Melo)
- Introduce function fro deleting/removing hist_entry to avoid code duplication
(Arnaldo Carvalho de Melo)
- Support parsing parameterized events (Cody P Schafer)
- Add support for IP address formats in libtraceevent (David Ahern)
- Fix typo in sample-parsing.c 'perf test' entry (Rasmus Villemoes)
- Remove some unused functions from color.c (Rickard Strandqvist)
"
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A step detector will generate an interrupt each time N step are detected.
A device that has such pedometer functionality is Freescale's MMA9553L:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf.
Introduce IIO_EV_TYPE_CHANGE event type for events that are generated
when the channel passes a threshold on the absolute change in value.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some devices export the current speed value of the user.
One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that computes the speed of the user based on the number of steps and
stride length.
Introduce a new channel type VELOCITY and a modifier for the magniture or
norm of the velocity vector, IIO_MOD_ROOT_SUM_SQUARED_X_Y_Z.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some devices export an estimation of the distance the user has covered
since the last reset.
One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that computes the distance based on the stride length and step rate.
Introduce a new channel type DISTANCE to export these values.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit 3161293ba6.
This interface was determined to be flawed and required too invasive a
fix for the RC cycle. This will be revisited in 3.20.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Adds reset to sysfs which will PERST the card. If load_image_on_perst is set
to "user" or "factory", the PERST will cause that image to be loaded.
load_image_on_perst is set to "user" for production.
"none" could be used for debugging. The PSL trace arrays are preserved which
then can be read through debugfs.
PERST also triggers CAPP recovery. An HMI comes in, which is handled by EEH.
EEH unbinds the driver, calls into Sapphire to reinitialize the PHB, then
rebinds the driver.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
load_image_on_perst identifies whether a PERST will cause the image to be
flashed to the card. And if so, which image.
Valid entries are: "none", "user" and "factory".
A value of "none" means PERST will not cause the image to be flashed. A
power cycle to the pcie slot is required to load the image.
"user" loads the user provided image and "factory" loads the factory image upon
PERST.
sysfs updates the cxl struct in the driver then calls cxl_update_image_control
to write the vals in the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Event parameters are a basic way for partial events to be specified in
sysfs with per-event names given to the fields that need to be filled in
when using a particular event.
It is intended for supporting cases where the single 'cpu' parameter is
insufficient. For example, POWER 8 has events for physical
sockets/cores/cpus that are accessible from with virtual machines. To
keep using the single 'cpu' parameter we'd need to perform a mapping
between Linux's cpus and the physical machine's cpus (in this case Linux
is running under a hypervisor). This isn't possible because bindings
between our cpus and physical cpus may not be fixed, and we probably
won't have a "cpu" on each physical cpu.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Cody P Schafer <dev@codyps.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1420679633-28856-4-git-send-email-sukadev@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
