[Description]
Output transfer function must be programmed per pipe as part of a front end
update when the plane changes, or output transfer function changes for a
given plane.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Corruption can occur in LB if vready_offset is not large enough.
DML calculates vready_offset for each pipe, but we currently select the
top pipe's vready_offset, which is not necessarily enough for all pipes
in the group.
[HOW]
Wherever program_global_sync is currently called, iterate through the
entire pipe group and find the highest vready_offset.
Reviewed-by: Dillon Varone <Dillon.Varone@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When transitioning a pipe in use (non-phantom) to become
a phantom pipe, we must fully disable the pipe first before
doing any phantom pipe programming
- Move phantom OTG enablement to after "regular" front-end
programming sequence (including wait for vupdate)
- If a pipe is being transitioned into a phantom pipe,
fully disable it first
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Software state expects pipes to be configured for ODM, but due to the transition
occurring on a plane disable, the ODM enablement code is not run.
[HOW?]
Update ODM when removing a plane, and dynamic ODM is active. Also acquire pipe
lock when removing a plane.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why and how]
This line was originally removed for a compliance issue, but then
reverted as it caused a fringe underflow case.
However, the addition of this line caused a underflow regression
when subVP is on, and it needs to be removed again. We plan to
fix subvp underflow and then re-add in this line. After that,
we will investigate what to do next for the compliance issue.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Skipping vblank during global sync update request can result in
underflow on certain displays.
[HOW]
Roll back to the previous behavior where DC waits for vblank during pipe
programming.
Fixes: 5d3e144214 ("drm/amd/display: do not wait for vblank during pipe programming")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Haiyi Zhou <Haiyi.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. As recommended by hardware team, don't enable APG when stream is not
enabled.
2. Move audio stream encoder programming into link_hwss.
[how]
1. Merge dp_audio_enable into enable audio stream hw sequence.
2. Move stream encoder programming into link hwss level to unify stream
encoder programming interface.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When using a device based on DCN32/321,
we have an issue where a second
4k@60Hz display does not light up,
and the system becomes unresponsive
for a few minutes. In the debug process,
it was possible to see a hang
in the function dcn20_post_unlock_program_front_end
in this part:
for (j = 0; j < TIMEOUT_FOR_PIPE_ENABLE_MS*1000
&& hubp->funcs->hubp_is_flip_pending(hubp); j++)
mdelay(1);
}
The hubp_is_flip_pending always returns positive
for waiting pending flips which is a symptom of
pipe hang. Additionally, the dmesg log shows
this message after a few minutes:
BUG: soft lockup - CPU#4 stuck for 26s!
...
[ +0.000003] dcn20_post_unlock_program_front_end+0x112/0x340 [amdgpu]
[ +0.000171] dc_commit_state_no_check+0x63d/0xbf0 [amdgpu]
[ +0.000155] ? dc_validate_global_state+0x358/0x3d0 [amdgpu]
[ +0.000154] dc_commit_state+0xe2/0xf0 [amdgpu]
This confirmed the hypothesis that we had a pipe
hanging somewhere. Next, after checking the
ftrace entries, we have the below weird
sequence:
[..]
2) | dcn10_lock_all_pipes [amdgpu]() {
2) 0.120 us | optc1_is_tg_enabled [amdgpu]();
2) | dcn20_pipe_control_lock [amdgpu]() {
2) | dc_dmub_srv_clear_inbox0_ack [amdgpu]() {
2) 0.121 us | amdgpu_dm_dmub_reg_write [amdgpu]();
2) 0.551 us | }
2) | dc_dmub_srv_send_inbox0_cmd [amdgpu]() {
2) 0.110 us | amdgpu_dm_dmub_reg_write [amdgpu]();
2) 0.511 us | }
2) | dc_dmub_srv_wait_for_inbox0_ack [amdgpu]() {
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
2) 0.110 us | amdgpu_dm_dmub_reg_read [amdgpu]();
[..]
We are not expected to read from dmub register
so many times and for so long. From the trace log,
it was possible to identify that the function
dcn20_pipe_control_lock was triggering the dmub
operation when it was unnecessary and causing
the hang issue. This commit drops the unnecessary
dmub code and, consequently, fixes the second display not
lighting up the issue.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SubVP has some issues related to how we allocate and enable it. This
commit fixes this behavior by adding the proper check and configuration
to the SubVP code path.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Clocks are updating based on the incoming context's support, however the new
compbuf size is not programmed prior to udpating clocks, which can result in
P-State hangs.
[HOW?]
Increase compbuf size prior to updating clocks.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The desktop plane and full-screen game plane may have different
gamut remap coefficients, if switching between desktop and
full-screen game without updating the gamut remap will cause
incorrect color.
[How]
Update gamut remap if planes change.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Original change 594b237b9a ("drm/amd/display: Add
interface to track PHY state") was implemented by assuming stream's
dpms off is equivalent to PHY power off.
This assumption doesn't hold in following situations:
1. MST multiple stream scenario, where multiple streams are sharing the
same PHY output. Toggle dpms off for one of the stream doesn't power
off the PHY due to the presence of other streams.
2. enable stream failure scenario, where enable stream fails due to
failure of link training. This will cause DPMS off is set to false, while
the actual PHY power state is off in certain cases.
Due to the problematic assumption, the logic will skip disabling
other streams for MST multiple stream scenario, therefore PHY is
not actually powered off.
[how]
1. Rework this refactor by moving PHY state update down to hardware
level, where we update PHY state in place when hardware sequencer
is actually changing the power state of the PHY hardware.
2. Reimplement symclk on TX off workaround in place when we are actually
calling transmitter control to power off PHY in dcn32. Note the workaround is
added due to the lack of proper software interface to set TX while keeping
symclk on. We plan to address this interface problem so we can set TX off
only without affecting symclk in future dcn versions.
Fixes: 594b237b9a ("drm/amd/display: Add interface to track PHY state")
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
In some cases the viewport position of the main pipes can change without
triggering a full update. In this case the subvp phantom viewports must
be updated accordingly.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
We would like to have visual confirm color support for SubVP.
1. Set visual confirm color to red: SubVP is enable on this
display;
2. Set visual confirm color to green: SubVP is enable on
other display and DRR is on this display;
3. Set visual confirm color to blue: SubVP is enable on
other display and DRR is off on this display;
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Exit SubVP if MPO is in use since SubVP + MPO together is not supported.
- Don't add SubVP at validation time if we see MPO is in use
Issues fixed in the SubVP / MPO transition:
1. Enable phantom pipes in post unlock function to prevent underflow
when an active pipe is being transitioned to be a phantom pipe (VTG
updates take place right away). Also must wait for VUPDATE of the main
pipe to complete first
2. Don't wait for MPCC idle when transitioning a phantom pipe to an
actual pipe. MPCC_STATUS is never asserted due to OTG being off for
phantom pipes
3. When transitioning an active pipe to phantom, program DET right away
(same as disabling the pipe) or the DET update will only take when
the phantom pipe is enabled which can cause DET allocation errors.
4. For K1/K2 programming of phantom pipes, use same settings as the
main pipe. Also don't program K1 / K2 = 0xF ever since the field is only
1 / 2 bits wide.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit enables the SubVP feature. To achieve that, we need to:
- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Memory clock switching has great potential for power savings.
[HOW]
The driver code was modified to notify the DMCUB firmware that it should
stretch the vertical blank of frames when a memory clock switch is about
to start so that no blackouts happen on the screen due to unavailability
of the frame buffer.
The driver logic to determine when such firmware assisted strategy can
be initiated is also implemented and consists on checking prerequisites
of the feature.
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Felipe Clark <felipe.clark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from 1 pipe to 4to1 mpc combine,
DppDtoClk aren't enabled for the disabled pipes
pior to programming the pipes. Upon optimizing
bandwidth, DppDto are enabled causing intermittent
underflow.
[How]
Update dppclk dto whenever pipe are flagged to
enable.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
New dividers in DCCG need to be programmed depending
on encoder/stream type since pixels per clock in
OTG/DIO is different
DIO also needs additional programming depending on
pixels per clock
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
According to the KMS man page, there is a
"Coverage" alpha blend mode that assumes the
pixel color values have NOT been pre-multiplied
and will be done when the actual blending to
the background color values happens.
Previously, this mode hasn't been enabled
in our driver and it was assumed that all
normal overlay planes are pre-multiplied
by default.
When a 3rd party app is used to input a image
in a specific format, e.g. PNG, as a source
of a overlay plane to blend with the background
primary plane, the pixel color values are not
pre-multiplied. So by adding "Coverage" blend
mode, our driver will support those cases.
Issue fixed: Overlay plane alpha channel blending is incorrect
Issue tracker: https://gitlab.freedesktop.org/drm/amd/-/issues/1769
Reference:
https://dri.freedesktop.org/docs/drm/gpu/drm-kms.html#plane-composition-properties
Adding Coverage support also enables IGT
kms_plane_alpha_blend Coverage subtests:
1. coverage-7efc
2. coverage-vs-premult-vs-constant
Changes
1. Add DRM_MODE_BLEND_COVERAGE blend mode capability
2. Add "pre_multiplied_alpha" flag for Coverage case
3. Read the correct flag and set the DCN MPCC
pre_multiplied register bit (only on overlay plane)
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1769
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Waiting for the vlbank every time a global sync update is requested,
including during full update flips, results in a stutter.
[How]
Do not wait for vblank during pipe programming.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
"Pre-multiplied" is the default pixel blend mode for KMS/DRM, as
documented in supported_modes of drm_plane_create_blend_mode_property():
https://cgit.freedesktop.org/drm/drm-misc/tree/drivers/gpu/drm/drm_blend.c
In this mode, both 'pixel alpha' and 'plane alpha' participate in the
calculation, as described by the pixel blend mode formula in KMS/DRM
documentation:
out.rgb = plane_alpha * fg.rgb +
(1 - (plane_alpha * fg.alpha)) * bg.rgb
Considering the blend config mechanisms we have in the driver so far,
the alpha mode that better fits this blend mode is the
_PER_PIXEL_ALPHA_COMBINED_GLOBAL_GAIN, where the value for global_gain
is the plane alpha (global_alpha).
With this change, alpha property stops to be ignored. It also addresses
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1734
v2:
* keep the 8-bit value for global_alpha_value (Nicholas)
* correct the logical ordering for combined global gain (Nicholas)
* apply to dcn10 too (Nicholas)
Signed-off-by: Melissa Wen <mwen@igalia.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we enter FREESYNC_STATE_VIDEO, we want to use the extra vblank
portion to enter zstate if possible.
[how]
When we enter freesync, a full update is triggered and the new vtotal
with extra lines is passed to dml in a stream update. The time gained
from extra vblank lines is calculated in microseconds. We allow zstate
entry if the time gained is greater than 5 ms, which is the current
policy. Furthermore, an optimized value for min_dst_y_next_start is
calculated and written to its register. When exiting freesync, another
full update is triggered and default values are restored.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow occurred while hubp ret pipe read is idle and the
second pipe is powered up and added. Flickering and underflow
are only observed on Pollock.
[How]
Check the hubp ret pipe read prior to unlock pipes.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Becle Lee <becle.lee@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Detbuffer size is dynamically set for dcn31x. At certain moment,
compbuf+(def size * num pipes) > config return buffer size causing
flickering. This is easily reproducible when MPO is
enabled with two displays.
[How]
At prepare BW, use the min comp buffer size. When it is to
optimize BW, set compbuf size back to maximum possible size.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Duncan Ma <duncanma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Clean up dc_link_hwss file in the preparation of breaking it down to
file for each encoder type. We temporarly move the original dp link
functions in link_hwss back to dc_link_dp. We will break dc_link_dp down
after link_hwss is in good shape.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
Need interface to lower clocks when in dc (power save)
mode. Must be able to work with p_state unsupported cases
Can cause flicker when OS notifies us of dc state change
how:
added dal3 interface for KMD
added pathway to query smu for this softmax
added blank before clock change to override underflow
added logic to change clk based on pstatesupport and softmax
added logic in prepare/optimize_bw to conform while changing
clocks
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This turns previously global functions into static, thus removing
compile-time warnings such as:
warning: no previous prototype for 'get_highest_allowed_voltage_level'
[-Wmissing-prototypes]
742 | unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
warning: no previous prototype for 'rv1_vbios_smu_send_msg_with_param'
[-Wmissing-prototypes]
102 | int rv1_vbios_smu_send_msg_with_param(struct clk_mgr_internal *clk_mgr, unsigned int msg_id, unsigned int param)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Changes since v1:
- As suggested by Rodrigo Siqueira:
1. Rewrite function signatures to make them more readable.
2. Get rid of unused functions in order to remove 'defined but not
used' warnings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Due to pass the wrong parameter down to the enable_stream_gating(),
it would cause the DSC of the removing stream would not be PG.
[HOW]
To pass the correct parameter down th the enable_stream_gating().
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect encoder assignments were being used while applying a new state
to hardware.
(1) When committing a new state to hardware requires resetting the
back-end, the encoder assignments of the current or old state should be
used when disabling the back-end; and the encoder assignments for the
next or new state should be used when re-enabling the back-end.
(2) Link training on hot plug could take over an encoder already in use
by another stream without first disabling it.
[How]
(1) Introduce a resource context 'link_enc_cfg_context' which includes:
- a mode to indicate when transitioning from current to next state.
- transient encoder assignments to use during this state transition.
Update the encoder configuration interface to respond to queries about
encoder assignment based on the mode of operation.
(2) Check if an encoder is already in use before attempting to perform
link training on hot plug.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.
[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Retrieve 128/132b link cap.
2. 128/132b link training and payload allocation.
3. UHBR10 link rate support.
[squash in warning fixes - Alex]
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
