The MAX96712 can support both a CSI-2 C-PHY and D-PHY bus. The initial
staging driver however only supported D-PHY and the bus-type property
was left optional.
In preparation for adding C-PHY support to the staging driver make the
bus-type property mandatory as it is needed to select the correct PHY
mode. Without the bus-type property present, the driver falls-back to
D-PHY mode, so the change is functionally backward compatible with old
DTS files lacking the property.
The only in-tree DTS file (renesas/r8a779a0-falcon-csi-dsi.dtsi) that
lacked the property uses D-PHY and have been updated.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert the text-based dt-bindings to yaml.
Changes from original txt:
* Take wording for various properties from other yaml bindings, this
removes e.g. volt amount from schema since it isn't really relevant
and the datasheet is a better source.
* Don't make reset-gpios a required property since it can be tied to
DOVDD instead.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
[Sakari Ailus: bump the maxItems for data-lanes to two]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version, based on the
full device name IMX290LLR. For consistency, add a new compatible string
for the colour version based on the IMX290LQR full device name, and
deprecate the current ambiguous compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reference common HDMI CEC adapter properties to simplify the binding and
have only one place of definition for common properties. The common CEC
binding expects also node name to be 'cec'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GMSL serial data bus width is normally selected by the BWS pin, but
it can also be configured by software. Add a DT property that allows
overriding the value of the BWS-selected bus width to support systems
whose BWS pin doesn't result in the correct value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The I2C speed on the remote side (the I2C master bus of the connected
serializers) is configurable, and doesn't need to match the speed of the
local bus (the slave bus of the MAX9286). All remote buses must use the
same speed, and the MAX9286 needs to be programmed accordingly. Add a
new DT property to select the speed to make it configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Power supplies for the ports can be controlled per port depending on the
hardware design. Support per-port supplies in the DT bindings, mutually
exclusive with the global supply.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Devicetree bindings document does not have to say in the title that
it is a "Devicetree binding", but instead just describe the hardware.
Drop trailing "Devicetree bindings" in various forms (also with
trailing full stop):
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD]evice[ -]\?[tT]ree [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD]evice[ -]\?[nN]ode [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD][tT] [bB]indings\?\.\?$/title: \1/' {} \;
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # IIO
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # input
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # media
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Link: https://lore.kernel.org/r/20221216163815.522628-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull devicetree updates from Rob Herring:
"DT Bindings:
- Various LED binding conversions and clean-ups. Convert the
ir-spi-led, pwm-ir-tx, and gpio-ir-tx LED bindings to schemas.
Consistently reference LED common.yaml or multi-led schemas and
disallow undefined properties.
- Convert IDT 89HPESx, pwm-clock, st,stmipid02, Xilinx PCIe hosts,
and fsl,imx-fb bindings to schema
- Add ata-generic, Broadcom u-boot environment, and dynamic MTD
sub-partitions bindings.
- Make all SPI based displays reference spi-peripheral-props.yaml
- Fix some schema property regex's which should be fixed strings or
were missing start/end anchors
- Remove 'status' in examples, again...
DT Core:
- Fix a possible NULL dereference in overlay functions
- Fix kexec reading 32-bit "linux,initrd-{start,end}" values (which
never worked)
- Add of_address_count() helper to count number of 'reg' entries
- Support .dtso extension for DT overlay source files. Rename staging
and unittest overlay files.
- Update dtc to upstream v1.6.1-63-g55778a03df61"
* tag 'devicetree-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (42 commits)
dt-bindings: leds: Add missing references to common LED schema
dt-bindings: leds: intel,lgm: Add missing 'led-gpios' property
of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry() and find_dup_cset_prop()
dt-bindings: lcdif: Fix constraints for imx8mp
media: dt-bindings: atmel,isc: Drop unneeded unevaluatedProperties
dt-bindings: Drop Jee Heng Sia
dt-bindings: thermal: cooling-devices: Add missing cache related properties
dt-bindings: leds: irled: ir-spi-led: convert to DT schema
dt-bindings: leds: irled: pwm-ir-tx: convert to DT schema
dt-bindings: leds: irled: gpio-ir-tx: convert to DT schema
dt-bindings: leds: mt6360: rework to match multi-led
dt-bindings: leds: lp55xx: rework to match multi-led
dt-bindings: leds: lp55xx: switch to preferred 'gpios' suffix
dt-bindings: leds: lp55xx: allow label
dt-bindings: leds: use unevaluatedProperties for common.yaml
dt-bindings: thermal: tsens: Add SM6115 compatible
of/kexec: Fix reading 32-bit "linux,initrd-{start,end}" values
dt-bindings: display: Convert fsl,imx-fb.txt to dt-schema
dt-bindings: Add missing start and/or end of line regex anchors
dt-bindings: qcom,pdc: Add missing compatibles
...
Now that a header exists with macros for the media interface bus-type
values, replace hardcoding numerical constants with the corresponding
macros in the DT binding examples.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the simple OV5645 Device Tree binding to json-schema.
The previous binding marked the below properties as required which was a
driver requirement and not the device requirement so just drop them from
the required list during the conversion.
- clock-frequency
- enable-gpios
- reset-gpios
Also drop the "clock-names" property as we have a single clock source for
the sensor and the driver has been updated to drop the clk referencing by
name.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Sony IMX290 DT binding from text to YAML. Add Manivannan as
a maintainer given that he is listed in MAINTAINERS for the file, as
volunteering myself.
The name of the input clock, "xclk", is wrong as the hardware manual
names it INCK. As the device has a single clock, the name could be
omitted, but that would require a corresponding change to the driver and
is thus a candidate for further patches.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Convert Dongwoon Anatech DW9714 camera voice coil lens driver to DT
schema and extend the bindings with vcc-supply (already used by driver)
and powerdown-gpios (based on datasheet, not used by the driver).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Pull devicetree updates from Rob Herring:
"Bindings:
- Convert smsc,lan91c111, qcom,spi-qup, qcom,msm-uartdm,
qcom,i2c-qup, qcom,gsbi, i2c-mt65xx, TI wkup_m3_ipc (and new
props), qcom,smp2p, TI timer, Mediatek gnss, Mediatek topckgen,
Mediatek apmixedsys, Mediatek infracfg, fsl,ls-extirq,
fsl,layerscape-dcfg, QCom PMIC SPMI, rda,8810pl-timer, Xilinx
zynqmp_ipi, uniphier-pcie, and Ilitek touchscreen controllers
- Convert various Arm Ltd peripheral IP bindings to schemas
- New bindings for Menlo board CPLD, DH electronics board CPLD,
Qualcomm Geni based QUP I2C, Renesas RZ/G2UL OSTM, Broafcom BCM4751
GNSS, MT6360 PMIC, ASIX USB Ethernet controllers, and
Microchip/SMSC LAN95xx USB Ethernet controllers
- Add vendor prefix for Enclustra
- Add various compatible string additions
- Various example fixes and cleanups
- Remove unused hisilicon,hi6220-reset binding
- Treewide fix properties missing type definition
- Drop some empty and unreferenced .txt bindings
- Documentation improvements for writing schemas
DT driver core:
- Drop static IRQ resources for DT platform devices as IRQ setup is
dynamic and drivers have all been converted to use
platform_get_irq() and friends
- Rework memory allocations and frees for overlays
- Continue overlay notifier callbacks on successful calls and add
unittests
- Handle 'interrupts-extended' in early DT IRQ setup
- Fix of_property_read_string() errors to match documentation
- Ignore disabled nodes in FDT API calls"
* tag 'devicetree-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (86 commits)
of/irq: fix typo in comment
dt-bindings: Fix properties without any type
Revert "dt-bindings: mailbox: qcom-ipcc: add missing properties into example"
dt-bindings: input: touchscreen: ilitek_ts_i2c: Absorb ili2xxx bindings
dt-bindings: timer: samsung,exynos4210-mct: define strict clock order
dt-bindings: timer: samsung,exynos4210-mct: drop unneeded minItems
dt-bindings: timer: cdns,ttc: drop unneeded minItems
dt-bindings: mailbox: zynqmp_ipi: convert to yaml
dt-bindings: usb: ci-hdrc-usb2: fix node node for ethernet controller
dt-bindings: net: add schema for Microchip/SMSC LAN95xx USB Ethernet controllers
dt-bindings: net: add schema for ASIX USB Ethernet controllers
of/fdt: Ignore disabled memory nodes
dt-bindings: arm: fix typos in compatible
dt-bindings: mfd: Add bindings child nodes for the Mediatek MT6360
dt-bindings: display: convert Arm Komeda to DT schema
dt-bindings: display: convert Arm Mali-DP to DT schema
dt-bindings: display: convert Arm HDLCD to DT schema
dt-bindings: display: convert PL110/PL111 to DT schema
dt-bindings: arm: convert vexpress-config to DT schema
dt-bindings: arm: convert vexpress-sysregs to DT schema
...
Now that the schema tools can extract type information for all
properties (in order to decode dtb files), finding properties missing
any type definition is fairly trivial though not yet automated.
Fix the various property schemas which are missing a type. Most of these
tend to be device specific properties which don't have a vendor prefix.
A vendor prefix is how we normally ensure a type is defined.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for everything in .../bindings/display/
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220519211411.2200720-1-robh@kernel.org
Define a new vendor property in the maxim,max9286 binding schema.
The new property allows to declare that the remote camera
power-over-coax is controlled by one of the MAX9286 gpio lines.
As it is currently not possible to establish a regulator as consumer
of the MAX9286 gpio controller for this purpose, the property allows to
declare that the camera power is controlled by the MAX9286 directly.
The property accepts a gpio-index (0 or 1) and one line polarity
flag as defined by dt-bindings/gpio/gpio.h.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Pull devicetree updates from Rob Herring:
"Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom
Command DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl,
Tegra I2C and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt
controllers, STB GPIO, STB waketimer, STB reset, iProc MDIO mux,
iProc PCIe, Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON,
SYSTEMPORT, AMAC, Northstar 2 PCIe PHY, GENET, moca PHY, GISB
arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in
preparation to move to validating DTB files directly (instead of
intermediate YAML representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes"
* tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (114 commits)
dt-bindings: net: mdio: Drop resets/reset-names child properties
dt-bindings: clock: samsung: convert S5Pv210 to dtschema
dt-bindings: clock: samsung: convert Exynos5410 to dtschema
dt-bindings: clock: samsung: convert Exynos5260 to dtschema
dt-bindings: clock: samsung: extend Exynos7 bindings with UFS
dt-bindings: clock: samsung: convert Exynos7 to dtschema
dt-bindings: clock: samsung: convert Exynos5433 to dtschema
dt-bindings: i2c: maxim,max96712: Add bindings for Maxim Integrated MAX96712
dt-bindings: iio: adi,ltc2983: Fix 64-bit property sizes
dt-bindings: power: maxim,max17040: Fix incorrect type for 'maxim,rcomp'
dt-bindings: interrupt-controller: arm,gic-v3: Fix 'interrupts' cell size in example
dt-bindings: iio/magnetometer: yamaha,yas530: Fix invalid 'interrupts' in example
dt-bindings: clock: imx5: Drop clock consumer node from example
dt-bindings: Drop required 'interrupt-parent'
dt-bindings: net: ti,dp83869: Drop value on boolean 'ti,max-output-impedance'
dt-bindings: net: wireless: mt76: Fix 8-bit property sizes
dt-bindings: PCI: snps,dw-pcie-ep: Drop conflicting 'max-functions' schema
dt-bindings: i2c: st,stm32-i2c: Make each example a separate entry
dt-bindings: net: stm32-dwmac: Make each example a separate entry
dt-bindings: net: Cleanup MDIO node schemas
...
