[Why]
It seems HPD interrupts are enabled by default for all connectors, even
if the hpd source isn't valid. An eDP for example, does not have a valid
hpd source (but does have a valid hpdrx source; see construct_phy()).
Thus, eDPs should have their hpd interrupt disabled.
In the past, this wasn't really an issue. Although the driver gets
interrupted, then acks by writing to hw registers, there weren't any
subscribed handlers that did anything meaningful (see
register_hpd_handlers()).
But things changed with the introduction of IPS. s2idle requires that
the driver allows IPS for DMUB fw to put hw to sleep. Since register
access requires hw to be awake, the driver will block IPS entry to do
so. And no IPS means no hw sleep during s2idle.
This was the observation on DCN35 systems with an eDP. During suspend,
the eDP toggled its hpd pin as part of the panel power down sequence.
The driver was then interrupted, and acked by writing to registers,
blocking IPS entry.
[How]
Since DC marks eDP connections as having invalid hpd sources (see
construct_phy()), DM should disable them at the hw level. Do so in
amdgpu_dm_hpd_init() by disabling all hpd ints first, then selectively
enabling ones for connectors that have valid hpd sources.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We advertise DCC as supported for NV12/P010 formats on GFX12,
but it would fail on this check on atomic commit.
Signed-off-by: David Rosca <david.rosca@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_* macros are more helpful that DRM_* macros since the former
indicates the associated DRM device that prints the error, which maybe
helpful when debugging.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Upgrading the kernel may cause some systems that were previously not using
a firmware specified brightness curve to use one.
In the event of problems with this curve (for example an interpolation
error) add a new dcdebugmask value that can be used to turn it off. Also
add an info message to show that custom brightness curves are currently in
use.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-6-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All cases except a failure to create a copy of the current context will
call dc_state_release() on the copied context.
Use a _free() macro to free the context and then adjust the error handling
flow to drop the unnecessary use of goto statements.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
amdgpu_dm_find_first_crtc_matching_connector can return NULL.
It is necessary to the returned connector before passing it
drm_atomic_get_new_connector_state which always assumes connector is
not NULL.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6d17270d1)
Cc: stable@vger.kernel.org
When switching to drm_edid, we slightly changed how to get edid by
removing the possibility of getting them from dc_link when in aux
transaction mode. As MST doesn't initialize the connector with
`drm_connector_init_with_ddc()`, restore the original behavior to avoid
functional changes.
v2:
- Fix build warning of unchecked dereference (kernel test bot)
CC: Alex Hung <alex.hung@amd.com>
CC: Mario Limonciello <mario.limonciello@amd.com>
CC: Roman Li <Roman.Li@amd.com>
CC: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 81262b1656)
[Why]
We must implement an ACPI re-timer programming interface and notify
ACPI driver whenever a PHY transition is about to take place.
Because some trace lengths on certain platforms are very long,
then a re-timer may need to be programmed whenever a PHY transition
takes place. The implementation of this re-timer programming interface
will notify ACPI driver that PHY transition is taking place and it
will trigger the re-timer as needed.
First we need to gather retimer information from ACPI interface.
Then, in the PRE case, the re-timer interface needs to be called before we call
transmitter ENABLE.
In the POST case, it has to be called after we call transmitter DISABLE.
[How]
Implemented ACPI retimer programming interface.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rafal Ostrowski <rostrows@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When switching to drm_edid, we slightly changed how to get edid by
removing the possibility of getting them from dc_link when in aux
transaction mode. As MST doesn't initialize the connector with
`drm_connector_init_with_ddc()`, restore the original behavior to avoid
functional changes.
v2:
- Fix build warning of unchecked dereference (kernel test bot)
CC: Alex Hung <alex.hung@amd.com>
CC: Mario Limonciello <mario.limonciello@amd.com>
CC: Roman Li <Roman.Li@amd.com>
CC: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename dc_plane_force_update_for_panic to
dc_plane_force_dcc_and_tiling_disable to describe the function operation
in the name. Also, this function might be used in other contexts, and a
more generic name can be helpful for this purpose.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't try to operate on a drm_wb_connector as an amdgpu_dm_connector.
While dereferencing aconnector->base will "work" it's wrong and
might lead to unknown bad things. Just... don't.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The source device outputs a full RGB signal, but TV may
be set to use limited RGB. The mismatch in color
range leads to a degradation in image quality.
Display driver should have the ability to switch
between the full and limited RGB to match TV's settings.
[HOW]
Add support of the linux DRM "Broadcast RGB" property, which
indicates the Quantization Range (Full vs Limited) used.
User space can set this property to be "Automatic", "Full"
or "Limited 16:235" to adjust the output color range.
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose the OEM i2c bus on boards that support it.
This bus is used for OEM specific features like RGB, etc.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow the creation of an OEM i2c bus and use the proper
DC helpers for that case.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
