When the hardware is synthesized with multiple queues, all queues are
disabled for default. This patch adds the rx queues configuration.
This patch was successfully tested in a Synopsys QoS Reference design.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4 IP can synthesized with 1-8 number of tx queues.
On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled
by default. For these IPs, the bitfield TXQEN is R/W.
Always enable tx queue 0. The write will have no effect on IPs synthesized
with DWC_EQOS_NUM_TXQ == 1.
The driver does still not utilize more than one tx queue in the IP.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA behavior is linked to descriptor management:
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
