Moved IRQ registration down to end of adv7511_probe().
If an IRQ already is pending during adv7511_probe
(before adv7511_cec_init) then cec_received_msg_ts
could crash using uninitialized data:
Unable to handle kernel read from unreadable memory at virtual address 00000000000003d5
Internal error: Oops: 96000004 [#1] PREEMPT_RT SMP
Call trace:
cec_received_msg_ts+0x48/0x990 [cec]
adv7511_cec_irq_process+0x1cc/0x308 [adv7511]
adv7511_irq_process+0xd8/0x120 [adv7511]
adv7511_irq_handler+0x1c/0x30 [adv7511]
irq_thread_fn+0x30/0xa0
irq_thread+0x14c/0x238
kthread+0x190/0x1a8
Fixes: 3b1b975003 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Mads Bligaard Nielsen <bli@bang-olufsen.dk>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240219-adv7511-cec-irq-crash-fix-v2-1-245e53c4b96f@bang-olufsen.dk
Backmerging to update drm-misc-next to the state of v6.8-rc3. Also
fixes a build problem with xe.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.
The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683d ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d31306 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.
This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.
Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.
Fixes: 20c827683d ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d31306 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
A null pointer dereference crash has been observed rarely on TI
platforms using sii9022 bridge:
[ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x]
[ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x]
[ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm]
[ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper]
[ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper]
[ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm]
[ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper]
[ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper]
[ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper]
[ 53.326401] drm_client_register+0x5c/0xa0 [drm]
[ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper]
[ 53.336881] tidss_probe+0x128/0x264 [tidss]
[ 53.341174] platform_probe+0x68/0xc4
[ 53.344841] really_probe+0x188/0x3c4
[ 53.348501] __driver_probe_device+0x7c/0x16c
[ 53.352854] driver_probe_device+0x3c/0x10c
[ 53.357033] __device_attach_driver+0xbc/0x158
[ 53.361472] bus_for_each_drv+0x88/0xe8
[ 53.365303] __device_attach+0xa0/0x1b4
[ 53.369135] device_initial_probe+0x14/0x20
[ 53.373314] bus_probe_device+0xb0/0xb4
[ 53.377145] deferred_probe_work_func+0xcc/0x124
[ 53.381757] process_one_work+0x1f0/0x518
[ 53.385770] worker_thread+0x1e8/0x3dc
[ 53.389519] kthread+0x11c/0x120
[ 53.392750] ret_from_fork+0x10/0x20
The issue here is as follows:
- tidss probes, but is deferred as sii902x is still missing.
- sii902x starts probing and enters sii902x_init().
- sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from
DRM's perspective.
- sii902x calls sii902x_audio_codec_init() and
platform_device_register_data()
- The registration of the audio platform device causes probing of the
deferred devices.
- tidss probes, which eventually causes sii902x_bridge_get_edid() to be
called.
- sii902x_bridge_get_edid() tries to use the i2c to read the edid.
However, the sii902x driver has not set up the i2c part yet, leading
to the crash.
Fix this by moving the drm_bridge_add() to the end of the
sii902x_init(), which is also at the very end of sii902x_probe().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 21d808405f ("drm/bridge/sii902x: Fix EDID readback")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
The synaptics-r63353 (panel-bridge) can only be configured in command mode.
So, samsung-dsim (bridge) must not be in display mode during the
prepare()/unprepare() of the panel-bridge. Setting the
"pre_enable_prev_first" flag to true allows the prepare() of the
panel-bridge to be called between the pre_enabled() and enabled() of the
bridge. So, the bridge can enter display mode only in the enabled().
The unprepare() of the panel-bridge is instead called between the disable()
and post_disable() of the bridge. So, the disable() must exit the display
mode (i .e. enter command mode) to allow the panel-bridge to receive DSI
commands.
samsung_dsim_atomic_pre_enable -> command mode
r63353_panel_prepare -> send DSI commands
samsung_dsim_atomic_enable -> enter display mode
samsung_dsim_atomic_disable -> exit display mode (command mode)
r63353_panel_unprepare -> send DSI commands
samsung_dsim_atomic_post_disable
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218084354.508942-2-dario.binacchi@amarulasolutions.com
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
The ps8640 bridge seems to expect everything to be power cycled at the
disable process, but sometimes ps8640_aux_transfer() holds the runtime
PM reference and prevents the bridge from suspend.
Prevent that by introducing a mutex lock between ps8640_aux_transfer()
and .post_disable() to make sure the bridge is really powered off.
Fixes: 826cff3f7e ("drm/bridge: parade-ps8640: Enable runtime power management")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240109120528.1292601-1-treapking@chromium.org
A null pointer dereference crash has been observed rarely on TI
platforms using sii9022 bridge:
[ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x]
[ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x]
[ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm]
[ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper]
[ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper]
[ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm]
[ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper]
[ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper]
[ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper]
[ 53.326401] drm_client_register+0x5c/0xa0 [drm]
[ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper]
[ 53.336881] tidss_probe+0x128/0x264 [tidss]
[ 53.341174] platform_probe+0x68/0xc4
[ 53.344841] really_probe+0x188/0x3c4
[ 53.348501] __driver_probe_device+0x7c/0x16c
[ 53.352854] driver_probe_device+0x3c/0x10c
[ 53.357033] __device_attach_driver+0xbc/0x158
[ 53.361472] bus_for_each_drv+0x88/0xe8
[ 53.365303] __device_attach+0xa0/0x1b4
[ 53.369135] device_initial_probe+0x14/0x20
[ 53.373314] bus_probe_device+0xb0/0xb4
[ 53.377145] deferred_probe_work_func+0xcc/0x124
[ 53.381757] process_one_work+0x1f0/0x518
[ 53.385770] worker_thread+0x1e8/0x3dc
[ 53.389519] kthread+0x11c/0x120
[ 53.392750] ret_from_fork+0x10/0x20
The issue here is as follows:
- tidss probes, but is deferred as sii902x is still missing.
- sii902x starts probing and enters sii902x_init().
- sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from
DRM's perspective.
- sii902x calls sii902x_audio_codec_init() and
platform_device_register_data()
- The registration of the audio platform device causes probing of the
deferred devices.
- tidss probes, which eventually causes sii902x_bridge_get_edid() to be
called.
- sii902x_bridge_get_edid() tries to use the i2c to read the edid.
However, the sii902x driver has not set up the i2c part yet, leading
to the crash.
Fix this by moving the drm_bridge_add() to the end of the
sii902x_init(), which is also at the very end of sii902x_probe().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 21d808405f ("drm/bridge/sii902x: Fix EDID readback")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
