The TBT DP tunnel BW request logic in the Thunderbolt Connection Manager
depends on the GFX driver reading out the sink's DPRX capabilities in
response to a long HPD pulse. Since in i915 this read-out can be blocked
by another connector's/encoder's hotplug event handling (which is
serialized by drm_mode_config::connection_mutex), do a dummy DPRX read-out
in the encoder's HPD pulse handler (which is not blocked by other
encoders).
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-21-imre.deak@intel.com
Suspend and resume DP tunnels during system suspend/resume, disabling
the BW allocation mode during suspend, re-enabling it after resume. This
reflects the link's BW management component (Thunderbolt CM) disabling
BWA during suspend. Before any BW requests the driver must read the
sink's DPRX capabilities (since the BW manager requires this
information, so snoops for it on AUX), so ensure this read takes place.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-20-imre.deak@intel.com
Add the atomic state during a modeset required to enable the DP tunnel
BW allocation mode on links where such a tunnel was detected. This state
applies to an already enabled output, the state added for a newly
enabled output will be computed and added/cleared to/from the atomic
state in a follow-up patch.
v2:
- s/old_crtc_state/crtc_state in intel_crtc_duplicate_state().
- Move intel_dp_tunnel_atomic_cleanup_inherited_state() to a follow-up
patch adding the corresponding state. (Ville)
- Move intel_dp_tunnel_atomic_clear_stream_bw() to a follow-up
patch adding the corresponding state.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-14-imre.deak@intel.com
Add support to enable the DP tunnel BW allocation mode. Follow-up
patches will call the required helpers added here to prepare for a
modeset on a link with DP tunnels, the last change in the patchset
actually enabling BWA.
With BWA enabled, the driver will expose the full mode list a display
supports, regardless of any BW limitation on a shared (Thunderbolt)
link. Such BW limits will be checked against only during a modeset, when
the driver has the full knowledge of each display's BW requirement.
If the link BW changes in a way that a connector's modelist may also
change, userspace will get a hotplug notification for all the connectors
sharing the same link (so it can adjust the mode used for a display).
The BW limitation can change at any point, asynchronously to modesets
on a given connector, so a modeset can fail even though the atomic check
for it passed. In such scenarios userspace will get a bad link
notification and in response is supposed to retry the modeset.
v2:
- Fix old vs. new connector state in intel_dp_tunnel_atomic_check_state().
(Ville)
- Fix propagating the error from
intel_dp_tunnel_atomic_compute_stream_bw(). (Ville)
- Move tunnel==NULL checks from driver to DRM core helpers. (Ville)
- Simplify return flow from intel_dp_tunnel_detect(). (Ville)
- s/dp_tunnel_state/inherited_dp_tunnels (Ville)
- Simplify struct intel_dp_tunnel_inherited_state. (Ville)
- Unconstify object pointers (vs. states) where possible. (Ville)
- Init crtc_state while declaring it in check_group_state(). (Ville)
- Join obj->base.id, obj->name arg lines in debug prints to reduce LOC.
(Ville)
- Add/rework intel_dp_tunnel_atomic_alloc_bw() to prepare for moving the
BW allocation from encoder hooks up to intel_atomic_commit_tail()
later in the patchset.
- Disable BW alloc mode during system suspend.
- Allocate the required BW for all tunnels during system resume.
- Add intel_dp_tunnel_atomic_clear_stream_bw() instead of the open-coded
sequence in a follow-up patch.
- Add function documentation to all exported functions.
- Add CONFIG_USB4 dependency to CONFIG_DRM_I915_DP_TUNNEL.
v3:
- Rebase on intel_dp_get_active_pipes() change in previous patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-4-imre.deak@intel.com
Sync instead of only try-sync non-blocking commits when getting the
active pipes through a given DP port. Atm intel_dp_get_active_pipes()
will only try to sync a given pipe and if that would block ignore the
pipe. This was supposed to avoid link retraining in case a pending
modeset would do that anyway, however that could incorrectly ignore
fastset pipes as well for instance (which don't retraing the link).
The TC port reset path needs to handle all pipes, even if a waiting for
a pending commit would block. To account for the above cases sync all
the pipes unconditionally.
This also prepares for a follow-up change enabling the DP tunnel BW
allocation mode which needs to ensure that all active pipes are synced
and returned from intel_dp_get_active_pipes().
v2:
- Add a separate function to try-sync the pipes. (Ville)
v3:
- Just sync the pipes unconditionally in intel_dp_get_active_pipes().
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-3-imre.deak@intel.com
On shared (Thunderbolt) links with DP tunnels, the modeset may need to
be retried on all connectors on the link due to a link BW limitation
arising only after the atomic check phase. To support this add a helper
function queuing a work to retry the modeset on a given port's connector
and at the same time any MST connector with streams through the same
port. A follow-up change enabling the DP tunnel Bandwidth Allocation
Mode will take this into use.
v2:
- Send the uevent only to enabled MST connectors. (Jouni)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-5-imre.deak@intel.com
The system resume display mode restoration should happen with an output
configuration matching that of the suspend time saved mode. Since the
restored mode configuration is subject to the bpp fallback logic,
starting out with an unlimited bpp and reducing the bpp as required by
any (MST) link BW limit, the resulting bpp will match the one during
suspend only if the BW limit checks during suspend and resume are
applied in an identical way. The latter is not guaranteed at the moment,
since the pre-suspend MST topology may not be in place during resume
(for instance if the MST sink was disconnected while being suspended),
which makes the MST link BW check accept the unlimited bpp mode
configuration unconditionally without ensuring that the required BW fits
into the available MST link BW.
To fix the above, initialize the bpp fallback logic with the max link
bpp / force-FEC limits left behind by the suspend time mode save.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-4-imre.deak@intel.com
Thomas Zimmermann asked to backmerge -rc6 for drm-misc branches,
there's a few same-area-changed conflicts (xe and amdgpu mostly) that
are getting a bit too annoying.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-misc-next for v6.9:
UAPI Changes:
- changes to fdinfo stats
Cross-subsystem Changes:
agp:
- remove unused type field from struct agp_bridge_data
Core Changes:
ci:
- update test names
- cleanups
gem:
- add stats for shared buffers plus updates to amdgpu, i915, xe
Documentation:
- fixes
syncobj:
- fixes to waiting and sleeping
Driver Changes:
bridge:
- adv7511: fix crash on irq during probe
- dw_hdmi: set bridge type
host1x:
- cleanups
ivpu:
- updates to firmware API
- refactor BO allocation
meson:
- fix error handling in probe
panel:
- revert "drm/panel-edp: Add auo_b116xa3_mode"
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
renesas:
- add RZ/G2L DU support plus DT bindings
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240222135841.GA6677@localhost.localdomain
Currently we are only checking capability of remote device and not
immediate downstream device but during capability check we need are
concerned with only the HDCP capability of downstream device.
During i915_display_info reporting we need HDCP Capability for both
the monitors and downstream branch device if any this patch adds that.
--v2
-Use MST Hub HDCP version [Ankit]
--v3
-Redefined how we seprate remote and direct read to make sure HDMI
shim functions are not touched [Ankit]
--v4
- Fix the conditions so that hdcp_info with remote_req true is sent
only when encoder is mst [Ankit]
--v5
-No need to have the MST Hub version in i915_hdcp_sink_capability[Ankit]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223081453.1576918-9-suraj.kandpal@intel.com
Create a remote HDCP capability shim function which can read the
remote monitor HDCP capability when in MST configuration.
--v2
-Add an assertion to make sure only mst encoder call this remote_cap
function [Ankit]
--v3
-rename remote_hdcp_cap to remote_hdcp_capability [Jani]
--v4
-fix hdcp2_prerequisite check condition
-Move intel_dp_hdcp_get_remote_capability to dp_mst shim instead of
having it in dp shim [Ankit]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226051017.1652970-2-suraj.kandpal@intel.com
If fixed refresh rate program the PKGC_LATENCY register
with the highest latency from level 1 and above LP registers
and program ADDED_WAKE_TIME = DSB execution time.
else program PKGC_LATENCY with all 1's and ADDED_WAKE_TIME as 0.
This is used to improve package C residency by sending the highest
latency tolerance requirement (LTR) when the planes are done with the
frame until the next frame programming window (set context latency,
window 2) starts.
Bspec: 68986
--v2
-Fix indentation [Chaitanya]
--v3
-Take into account if fixed refrersh rate or not [Vinod]
-Added wake time dependengt on DSB execution time [Vinod]
-Use REG_FIELD_PREP [Jani]
-Call program_pkgc_latency from appropriate place [Jani]
-no need for the ~0 while setting max latency [Jani]
-change commit message to add the new changes made in.
--v4
-Remove extra blank line [Vinod]
-move the vrr.enable check to previous loop [Vinod]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240219063638.1467114-1-suraj.kandpal@intel.com
