Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().
Fixes: 195aae321c ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.
All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33a ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit d9962b0d42 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
(including usb_submit_urb() returning an error).
In that case:
* Since the USB reset is perform in a separate thread asynchronously,
it can run at anytime USB device lock is not held - even before
rtl8152_open() has exited with an error and caused __dev_open() to
clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
true (since __LINK_STATE_START wasn't cleared) so it won't exit
early.
* rtl8152_pre_reset() will then hang in napi_disable() because
napi_enable() was never called.
We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.
Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.
Fixes: d9962b0d42 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Reported-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an EEH error is encountered by a PCI adapter, the EEH driver
modifies the PCI channel's state as shown below:
enum {
/* I/O channel is in normal state */
pci_channel_io_normal = (__force pci_channel_state_t) 1,
/* I/O to channel is blocked */
pci_channel_io_frozen = (__force pci_channel_state_t) 2,
/* PCI card is dead */
pci_channel_io_perm_failure = (__force pci_channel_state_t) 3,
};
If the same EEH error then causes the tg3 driver's transmit timeout
logic to execute, the tg3_tx_timeout() function schedules a reset
task via tg3_reset_task_schedule(), which may cause a race condition
between the tg3 and EEH driver as both attempt to recover the HW via
a reset action.
EEH driver gets error event
--> eeh_set_channel_state()
and set device to one of
error state above scheduler: tg3_reset_task() get
returned error from tg3_init_hw()
--> dev_close() shuts down the interface
tg3_io_slot_reset() and
tg3_io_resume() fail to
reset/resume the device
To resolve this issue, we avoid the race condition by checking the PCI
channel state in the tg3_reset_task() function and skip the tg3 driver
initiated reset when the PCI channel is not in the normal state. (The
driver has no access to tg3 device registers at this point and cannot
even complete the reset task successfully without external assistance.)
We'll leave the reset procedure to be managed by the EEH driver which
calls the tg3_io_error_detected(), tg3_io_slot_reset() and
tg3_io_resume() functions as appropriate.
Adding the same checking in tg3_dump_state() to avoid dumping all
device registers when the PCI channel is not in the normal state.
Signed-off-by: Thinh Tran <thinhtr@linux.vnet.ibm.com>
Tested-by: Venkata Sai Duggi <venkata.sai.duggi@ibm.com>
Reviewed-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201001911.656-1-thinhtr@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a NIXLF is not attached to a PF/VF device then
nix_get_nixlf function fails and returns proper error
code. But npc_get_default_entry_action does not check it
and uses garbage value in subsequent calls. Fix this
by cheking the return value of nix_get_nixlf.
Fixes: 967db3529e ("octeontx2-af: add support for multicast/promisc packet replication feature")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the mailbox messages sent to AF needs to be guarded
by mutex lock. Add the missing lock in otx2_get_pauseparam
function.
Fixes: 75f3627099 ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
Call trace:
dump_backtrace+0x9c/0x100
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
ravb_open+0x70/0xa58
__dev_open+0xf4/0x1e8
__dev_change_flags+0x198/0x218
dev_change_flags+0x2c/0x80
devinet_ioctl+0x640/0x708
inet_ioctl+0x1e4/0x200
sock_do_ioctl+0x50/0x108
sock_ioctl+0x240/0x358
__arm64_sys_ioctl+0xb0/0x100
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0xc0/0xc8
el0t_64_sync+0x190/0x198
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
// ...
done:
rtnl_unlock();
out:
return ret;
}
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Take into account these indication.
Fixes: 1089877ada ("ravb: Add RZ/G2L MII interface support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
Fixes: 0d13a1a464 ("ravb: Add reset support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is an error when an interface has the following conditions:
- PF is in an aggregate (bond)
- PF has VFs created on it
- bond is in a state where it is failed-over to the secondary interface
- A VF reset is issued on one or more of those VFs
The issue is generated by the originating PF trying to rebuild or
reconfigure the VF resources. Since the bond is failed over to the
secondary interface the queue contexts are in a modified state.
To fix this issue, have the originating interface reclaim its resources
prior to the tear-down and rebuild or reconfigure. Then after the process
is complete, move the resources back to the currently active interface.
There are multiple paths that can be used depending on what triggered the
event, so create a helper function to move the queues and use paired calls
to the helper (back to origin, process, then move back to active interface)
under the same lag_mutex lock.
Fixes: 1e0f9881ef ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20231127212340.1137657-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
wireless fixes:
- debugfs had a deadlock (removal vs. use of files),
fixes going through wireless ACKed by Greg
- support for HT STAs on 320 MHz channels, even if it's
not clear that should ever happen (that's 6 GHz), best
not to WARN()
- fix for the previous CQM fix that broke most cases
- various wiphy locking fixes
- various small driver fixes
* tag 'wireless-2023-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: use wiphy locked debugfs for sdata/link
wifi: mac80211: use wiphy locked debugfs helpers for agg_status
wifi: cfg80211: add locked debugfs wrappers
debugfs: add API to allow debugfs operations cancellation
debugfs: annotate debugfs handlers vs. removal with lockdep
debugfs: fix automount d_fsdata usage
wifi: mac80211: handle 320 MHz in ieee80211_ht_cap_ie_to_sta_ht_cap
wifi: avoid offset calculation on NULL pointer
wifi: cfg80211: hold wiphy mutex for send_interface
wifi: cfg80211: lock wiphy mutex for rfkill poll
wifi: cfg80211: fix CQM for non-range use
wifi: mac80211: do not pass AP_VLAN vif pointer to drivers during flush
wifi: iwlwifi: mvm: fix an error code in iwl_mvm_mld_add_sta()
wifi: mt76: mt7925: fix typo in mt7925_init_he_caps
wifi: mt76: mt7921: fix 6GHz disabled by the missing default CLC config
====================
Link: https://lore.kernel.org/r/20231129150809.31083-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2023-11-30
We've added 5 non-merge commits during the last 7 day(s) which contain
a total of 10 files changed, 66 insertions(+), 15 deletions(-).
The main changes are:
1) Fix AF_UNIX splat from use after free in BPF sockmap,
from John Fastabend.
2) Fix a syzkaller splat in netdevsim by properly handling offloaded
programs (and not device-bound ones), from Stanislav Fomichev.
3) Fix bpf_mem_cache_alloc_flags() to initialize the allocation hint,
from Hou Tao.
4) Fix netkit by rejecting IFLA_NETKIT_PEER_INFO in changelink,
from Daniel Borkmann.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, sockmap: Add af_unix test with both sockets in map
bpf, sockmap: af_unix stream sockets need to hold ref for pair sock
netkit: Reject IFLA_NETKIT_PEER_INFO in netkit_change_link
bpf: Add missed allocation hint for bpf_mem_cache_alloc_flags()
netdevsim: Don't accept device bound programs
====================
Link: https://lore.kernel.org/r/20231129234916.16128-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ndo_stop() is RTNL-protected by net core, and the worker function takes
RTNL as well. Therefore we will deadlock when trying to execute a
pending work synchronously. To fix this execute any pending work
asynchronously. This will do no harm because netif_running() is false
in ndo_stop(), and therefore the work function is effectively a no-op.
However we have to ensure that no task is running or pending after
rtl_remove_one(), therefore add a call to cancel_work_sync().
Fixes: abe5fc42f9 ("r8169: use RTNL to protect critical sections")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/12395867-1d17-4cac-aa7d-c691938fcddf@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
TC ingress policer rules depends on interface receive queue
contexts since the bandwidth profiles are attached to RQ
contexts. When an interface is brought down all the queue
contexts are freed. This in turn frees bandwidth profiles in
hardware causing ingress police rules non-functional after
the interface is brought up. Fix this by applying all the ingress
police rules config to hardware in otx2_open. Also allow
adding ingress rules only when interface is running
since no contexts exist for the interface when it is down.
Fixes: 68fbff68db ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930217-5707-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A loop in rvu_mbox_handler_nix_bandprof_free() contains
a break if (idx == MAX_BANDPROF_PER_PFFUNC),
but if idx may reach MAX_BANDPROF_PER_PFFUNC
buffer '(*req->prof_idx)[layer]' overflow happens before that check.
The patch moves the break to the
beginning of the loop.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e8e095b3b3 ("octeontx2-af: cn10k: Bandwidth profiles config support").
Signed-off-by: Elena Salomatkina <elena.salomatkina.cmc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20231124210802.109763-1-elena.salomatkina.cmc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The read is currently with RCU and the write can deadlock,
convert both for the sake of illustration.
Make mac80211 depend on cfg80211 debugfs to get the helpers,
but mac80211 debugfs without it does nothing anyway. This
also required some adjustments in ath9k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The blamed commit added support for Rx copybreak. This meant that for
certain frame sizes, a new skb was allocated and the initial data buffer
was recycled. Instead of waiting to recycle the Rx buffer only after all
processing was done on it (like accessing the parse results or timestamp
information), the code path just went ahead and re-used the buffer right
away.
This sometimes lead to corrupted HW and SW annotation areas.
Fix this by delaying the moment when the buffer is recycled.
Fixes: 50f826999a ("dpaa2-eth: add rx copybreak support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.
Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.
Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.
This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
- 64 bytes for the software annotation area
- 64 bytes to account for a 64 byte aligned buffer address
Fixes: 6e2387e8f1 ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit b92143d442 ("net: dsa: mv88e6xxx: add infrastructure for
phylink_pcs") probing of a Marvell 88e6350 switch causes a NULL pointer
de-reference like this example:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in:
CPU: 0 PID: 8 Comm: kworker/u2:0 Not tainted 6.7.0-rc2-dirty #26
Hardware name: Marvell Armada 370/XP (Device Tree)
Workqueue: events_unbound deferred_probe_work_func
PC is at mv88e6xxx_port_setup+0x1c/0x44
LR is at dsa_port_devlink_setup+0x74/0x154
pc : [<c057ea24>] lr : [<c0819598>] psr: a0000013
sp : c184fce0 ip : c542b8f4 fp : 00000000
r10: 00000001 r9 : c542a540 r8 : c542bc00
r7 : c542b838 r6 : c5244580 r5 : 00000005 r4 : c5244580
r3 : 00000000 r2 : c542b840 r1 : 00000005 r0 : c1a02040
...
The Marvell 6350 switch has no SERDES interface and so has no
corresponding pcs_ops defined for it. But during probing a call is made
to mv88e6xxx_port_setup() which unconditionally expects pcs_ops to exist -
though the presence of the pcs_ops->pcs_init function is optional.
Modify code to check for pcs_ops first, before checking for and calling
pcs_ops->pcs_init. Modify checking and use of pcs_ops->pcs_teardown
which may potentially suffer the same problem.
Fixes: b92143d442 ("net: dsa: mv88e6xxx: add infrastructure for phylink_pcs")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled") Marvell 88e6350 switches fail to be probed:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
mv88e6085 d0072004.mdio-mii:11: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
mv88e6085: probe of d0072004.mdio-mii:11 failed with error -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities. Create a new dedicated phylink_get_caps for the
6351 family (which the 6350 is one of) to properly support their set of
capabilities.
According to chip.h the 6351 switch family includes the 6171, 6175, 6350
and 6351 switches, so update each of these to use the correct
phylink_get_caps.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before returning the rswitch_start_xmit() in the error path,
dev_kfree_skb_any() should be called. So, fix it.
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit d938a8cca8 ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.
The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.
For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.
If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.
The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.
Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.
This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.
Fixes: d938a8cca8 ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.
Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.
In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.
Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.
A following change will fix the reset path to properly restore user
timestamping configuration completely.
This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa0877 ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b81 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3fea ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:
$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
numtxqueues 1 numrxqueues 1
and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.
Fixes: 4fc418053e ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
