The function mse102x_rx_pkt_spi is used in two cases:
* initial polling to re-arm RX interrupt
* level based RX interrupt handler
Both of them doesn't need an open-coded retry mechanism.
In the first case the function can be called again, if the return code
is IRQ_NONE. This keeps the error behavior during netdev open.
In the second case the proper retry would be handled implicit by
the SPI interrupt. So drop the retry code and simplify the receive path.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20250509120435.43646-7-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MSE102x doesn't provide any interrupt register, so the only way
to handle the level interrupt is to fetch the whole packet from
the MSE102x internal buffer via SPI. So in cases the interrupt
handler fails to do this, it should return IRQ_NONE. This allows
the core to disable the interrupt in case the issue persists
and prevent an interrupt storm.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20250509120435.43646-6-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After removal of the invalid command counter only a relevant debug
message is left, which can be cumbersome. So add a new flag to debugfs,
which indicates whether the driver has ever received a valid CMD.
This helps to differentiate between general and temporary receive
issues.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250509120435.43646-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are several reasons for an invalid command response
by the MSE102x:
* SPI line interferences
* MSE102x is in reset or has no firmware
* MSE102x is busy
* no packet in MSE102x receive buffer
So the counter for invalid command isn't very helpful without
further context. So drop the confusing statistics counter,
but keep the debug messages about "unexpected response" in order
to debug possible hardware issues.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250509120435.43646-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As long as the MSE102x is not operational, every packet transmission
will run into a TX timeout and flood the kernel log. So log only the
first TX timeout and a user is at least informed about this issue.
The amount of timeouts are still available via netstat.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240827191000.3244-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This macro has the advantage over SET_SYSTEM_SLEEP_PM_OPS that we don't
have to care about when the functions are actually used.
Also make use of pm_sleep_ptr() to discard all PM_SLEEP related
stuff if CONFIG_PM_SLEEP isn't enabled.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240827191000.3244-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SPI devices use the spi_device_id for module autoloading even on
systems using device tree, after commit 5fa6863ba6 ("spi: Check
we have a spi_device_id for each DT compatible"), kernel warns as
follows since the spi_device_id is missing:
SPI driver mse102x has no spi_device_id for vertexcom,mse1021
SPI driver mse102x has no spi_device_id for vertexcom,mse1022
Add spi_device_id entries to silence the warnings, and ensure driver
module autoloading works.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220922065717.1448498-1-weiyongjun@huaweicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sorry for being rude but new vendors/drivers are supposed to be disabled
by default, otherwise we will have to manually keep track of all vendors
we are not interested in building.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
CC: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements an SPI protocol driver for Vertexcom MSE102x
Homeplug GreenPHY chip.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
