Pull new SoC support from Arnd Bergmann:
"These five newly supported chips come with both devicetree
descriptions and the changes to wire them up to the build system for
easier bisection.
The chips in question are:
- Marvell PXA1908 was the first 64-bit mobile phone chip from Marvell
in the product line that started with the Digital StrongARM SA1100
based PDAs and continued with the Intel PXA2xx that dominated early
smartphones. This one only made it only into a few products before
the entire product line was cut in 2015.
- The QiLai SoC is made by RISC-V core designer Andes Technologies
and is in the 'Voyager' reference board in MicroATX form factor. It
uses four in-order AX45MP cores, which is the midrange product from
Andes.
- CIX P1 is one of the few Arm chips designed for small workstations,
and this one uses 12 Cortex-A720/A520 cores, making it also one of
the only ARMv9.2 machines that one can but at the moment.
- Axiado AX3000 is an embedded chip with relative small Cortex-A53
CPU cores described as a "Trusted Control/Compute Unit" that can be
used as a BMC in servers. In addition to the usual I/O, this one
comes with 10GBit ethernet and and a 4TOPS NPU.
- Sophgo SG2000 is an embedded chip that comes with both RISC-V and
Arm cores that can run Linux. This was already supported for RISC-V
but now it also works on Arm
One more chip, the Black Sesame C1200 did not make it in tirm for the
merge window"
* tag 'soc-newsoc-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
arm64: defconfig: Enable rudimentary Sophgo SG2000 support
arm64: Add SOPHGO SOC family Kconfig support
arm64: dts: sophgo: Add Duo Module 01 Evaluation Board
arm64: dts: sophgo: Add Duo Module 01
arm64: dts: sophgo: Add initial SG2000 SoC device tree
MAINTAINERS: Add entry for Axiado
arm64: defconfig: enable the Axiado family
arm64: dts: axiado: Add initial support for AX3000 SoC and eval board
arm64: add Axiado SoC family
dt-bindings: i3c: cdns: add Axiado AX3000 I3C controller
dt-bindings: serial: cdns: add Axiado AX3000 UART controller
dt-bindings: gpio: cdns: add Axiado AX3000 GPIO variant
dt-bindings: gpio: cdns: convert to YAML
dt-bindings: arm: axiado: add AX3000 EVK compatible strings
dt-bindings: vendor-prefixes: Add Axiado Corporation
MAINTAINERS: Add CIX SoC maintainer entry
arm64: dts: cix: Add sky1 base dts initial support
dt-bindings: clock: cix: Add CIX sky1 scmi clock id
arm64: defconfig: Enable CIX SoC
mailbox: add CIX mailbox driver
...
The UART controllers in most Rockchip SoCs are part of power domains
that are always powered on. These always powered on power domains have
typically not been described in the device tree.
Because these power domains have been left out of the device tree there
has not been any real need to properly describe the UART controllers
power domain of Rockchip SoCs.
On Rockchip RK3528 the UART controllers are spread out among the
described PD_RKVENC, PD_VO and PD_VPU power domains. However, one UART
controller belong to an undescribed always powered on power domain.
Add support to describe an optional power-domains for the UART
controllers.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250723085654.2273324-5-jonas@kwiboo.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add binding for AX3000 UART controller. So far, no changes known,
so it can fallback to default compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update the RSCI binding to support an optional secondary clock input on
the RZ/T2H SoC. At boot, the RSCI operates using the default synchronous
clock (PCLKM core clock), which is enabled by the bootloader. However, to
support a wider range of baud rates, the hardware also requires an
asynchronous external clock input. Clock selection is controlled
internally by the CCR3 register in the RSCI block.
Due to an incomplete understanding of the hardware, the original binding
defined only a single clock ("fck"), which is insufficient to describe the
full capabilities of the RSCI on RZ/T2H. This update corrects the binding
by allowing up to three clocks and defining the `clock-names` as
"operation", "bus", and optionally "sck" for the asynchronous clock input.
This is an ABI change, as it modifies the expected number and names of
clocks. However, since there are no in-kernel consumers of this binding
yet, the change is considered safe and non-disruptive.
Also remove the unneeded `serial0` alias from the DTS example and use
the R9A09G077_CLK_PCLKM macro for core clock.
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250630202323.279809-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial driver fixes from Greg KH:
"Here are five small serial and tty and vt fixes for 6.16-rc4. Included
in here are:
- kerneldoc fixes for recent vt changes
- imx serial driver fix
- of_node sysfs fix for a regression
- vt missing notification fix
- 8250 dt bindings fix
All of these have been in linux-next for a while with no reported issues"
* tag 'tty-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
dt-bindings: serial: 8250: Make clocks and clock-frequency exclusive
serial: imx: Restore original RXTL for console to fix data loss
serial: core: restore of_node information in sysfs
vt: fix kernel-doc warnings in ucs_get_fallback()
vt: add missing notification when switching back to text mode
Allow clock 'uartclk' and 'reg' for nxp,lpc1850-uart to align existed
driver and dts. It is really old platform. Keep the same restriction for
others.
Allow dmas and dma-names property, which allow maxItems 4 because very old
platform (arch/arm/boot/dts/nxp/lpc/lpc18xx.dtsi) use duplicate "tx", "rx",
"tx", "rx" as dma-names.
Fix below CHECK_DTB warnings:
arch/arm/boot/dts/nxp/lpc/lpc4337-ciaa.dtb: serial@40081000 (nxp,lpc1850-uart): clock-names: ['uartclk', 'reg'] is too long
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250602142745.942568-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull devicetree fixes from Rob Herring:
- Convert altr,uart-1.0 and altr,juart-1.0 to DT schema. These were
applied for nios2, but never sent upstream.
- Fix extra '/' in fsl,ls1028a-reset '$id' path
- Fix warnings in ti,sn65dsi83 schema due to unnecessary $ref.
* tag 'devicetree-fixes-for-6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: serial: Convert altr,uart-1.0 to DT schema
dt-bindings: serial: Convert altr,juart-1.0 to DT schema
dt-bindings: soc: fsl,ls1028a-reset: Drop extra "/" in $id
dt-bindings: drm/bridge: ti-sn65dsi83: drop $ref to fix lvds-vod* warnings
The 8250 binding before converting to json-schema states,
- clock-frequency : the input clock frequency for the UART
or
- clocks phandle to refer to the clk used as per Documentation/devicetree
for clock-related properties, where "or" indicates these properties
shouldn't exist at the same time.
Additionally, the behavior of Linux's driver is strange when both clocks
and clock-frequency are specified: it ignores clocks and obtains the
frequency from clock-frequency, left the specified clocks unclaimed. It
may even be disabled, which is undesired most of the time.
But "anyOf" doesn't prevent these two properties from coexisting, as it
considers the object valid as long as there's at LEAST one match.
Let's switch to "oneOf" and disallows the other property if one exists,
precisely matching the original binding and avoiding future confusion on
the driver's behavior.
Fixes: e69f5dc623 ("dt-bindings: serial: Convert 8250 to json-schema")
Cc: stable <stable@kernel.org>
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250623093445.62327-1-ziyao@disroot.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Altera JTAG UART binding to DT schema. The "ALTR,uart-1.0"
compatible has long been deprecated, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Convert the Altera JTAG UART binding to DT schema. The "ALTR,juart-1.0"
compatible has long been deprecated, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Pull tty/serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.16-rc1.
A little more churn than normal in this portion of the kernel for this
development cycle, Jiri and Nicholas were busy with cleanups and
reviews and fixes for the vt unicode handling logic which composed
most of the overall work in here.
Major changes are:
- vt unicode changes/reverts/changes from Nicholas. This should help
out a lot with screen readers and others that rely on vt console
support
- lock guard additions to the core tty/serial code to clean up lots
of error handling logic
- 8250 driver updates and fixes
- device tree conversions to yaml
- sh-sci driver updates
- other small cleanups and updates for serial drivers and tty core
portions
All of these have been in linux-next for 2 weeks with no reported issues"
* tag 'tty-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (105 commits)
tty: serial: 8250_omap: fix TX with DMA for am33xx
vt: add VT_GETCONSIZECSRPOS to retrieve console size and cursor position
vt: bracketed paste support
vt: remove VT_RESIZE and VT_RESIZEX from vt_compat_ioctl()
vt: process the full-width ASCII fallback range programmatically
vt: make use of ucs_get_fallback() when glyph is unavailable
vt: add ucs_get_fallback()
vt: create ucs_fallback_table.h_shipped with gen_ucs_fallback_table.py
vt: introduce gen_ucs_fallback_table.py to create ucs_fallback_table.h
vt: move glyph determination to a separate function
vt: make sure displayed double-width characters are remembered as such
vt: ucs.c: fix misappropriate in_range() usage
serial: max3100: Replace open-coded parity calculation with parity8()
dt-bindings: serial: 8250_omap: Drop redundant properties
dt-bindings: serial: Convert socionext,milbeaut-usio-uart to DT schema
dt-bindings: serial: Convert microchip,pic32mzda-uart to DT schema
dt-bindings: serial: Convert arm,sbsa-uart to DT schema
dt-bindings: serial: Convert snps,arc-uart to DT schema
dt-bindings: serial: Convert marvell,armada-3700-uart to DT schema
dt-bindings: serial: Convert lantiq,asc to DT schema
...
Convert the Cirrus EP7209 UART binding to DT schema. There is no user of
"cirrus,ep7312-uart" other than the example, so drop it. Drop the
"aliases" node part as it is not relevant to the schema. The modem
control GPIOs are covered by the serial.yaml schema and don't have to be
listed in the schema.
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250506220021.2545820-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra UTC (UART Trace Controller) allows multiple clients within
the Tegra SoC to share a physical UART interface. It supports up to 16
clients. Each client operates as an independent UART endpoint with a
dedicated interrupt and 128-character TX/RX FIFOs.
Add device tree binding documentation for the Tegra UTC client.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250213125612.4705-2-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty / serial driver updates from Greg KH:
"Here is the tty/serial driver set of changes for 6.14-rc1. Nothing
major in here, it was delayed a bit due to a regression found in
linux-next which has now been reverted and verified that it is fixed.
Other than the reverts, highlights include:
- 8250 work to get the nbcon mode working (partially reverted)
- altera_jtaguart minor fixes
- fsl_lpuart minor updates
- sh-sci driver minor updatesa
- other tiny driver updates and cleanups
All of these have been in linux-next for a while, and now with no
reports of problems (thanks to the reverts)"
* tag 'tty-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (44 commits)
Revert "serial: 8250: Switch to nbcon console"
Revert "serial: 8250: Revert "drop lockdep annotation from serial8250_clear_IER()""
serial: sh-sci: Increment the runtime usage counter for the earlycon device
serial: sh-sci: Clean sci_ports[0] after at earlycon exit
serial: sh-sci: Do not probe the serial port if its slot in sci_ports[] is in use
serial: sh-sci: Move runtime PM enable to sci_probe_single()
serial: sh-sci: Drop __initdata macro for port_cfg
serial: kgdb_nmi: Remove unused knock code
tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN
tty: xilinx_uartps: split sysrq handling
serial: 8250: Revert "drop lockdep annotation from serial8250_clear_IER()"
serial: 8250: Switch to nbcon console
serial: 8250: Provide flag for IER toggling for RS485
serial: 8250: Use high-level writing function for FIFO
serial: 8250: Use frame time to determine timeout
serial: 8250: Adjust the timeout for FIFO mode
tty: atmel_serial: Use of_property_present() for non-boolean properties
serial: sc16is7xx: Add polling mode if no IRQ pin is available
dt-bindings: serial: sc16is7xx: Add description for polling mode
tty: serial: atmel: make it selectable for ARCH_LAN969X
...
Found SpacemiT's K1 uart controller is compatible with
Intel's Xscale uart, but it's still worth to introduce a new compatible.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
