On DCE 6, DP audio was not working. However, it worked when an
HDMI monitor was also plugged in.
Looking at dce_aud_wall_dto_setup it seems that the main
difference is that we use DTO1 when only DP is plugged in.
When programming DTO1, it uses audio_dto_source_clock_in_khz
which is set from get_dp_ref_freq_khz
The dce60_get_dp_ref_freq_khz implementation looks incorrect,
because DENTIST_DISPCLK_CNTL seems to be always zero on DCE 6,
so it isn't usable.
I compared dce60_get_dp_ref_freq_khz to the legacy display code,
specifically dce_v6_0_audio_set_dto, and it turns out that in
case of DCE 6, it needs to use the display clock. With that,
DP audio started working on Pitcairn, Oland and Cape Verde.
However, it still didn't work on Tahiti. Despite having the
same DCE version, Tahiti seems to have a different audio device.
After some trial and error I realized that it works with the
default display clock as reported by the VBIOS, not the current
display clock.
The patch was tested on all four SI GPUs:
* Pitcairn (DCE 6.0)
* Oland (DCE 6.4)
* Cape Verde (DCE 6.0)
* Tahiti (DCE 6.0 but different)
The testing was done on Samsung Odyssey G7 LS28BG700EPXEN on
each of the above GPUs, at the following settings:
* 4K 60 Hz
* 1080p 60 Hz
* 1080p 144 Hz
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 645cc7863d)
Cc: stable@vger.kernel.org
Adjust the nominal (and performance) clocks for DCE 8-10,
and set them to 625 MHz, which is the value used by the legacy
display code in amdgpu_atombios_get_clock_info.
This was tested with Hawaii, Tonga and Fiji.
These GPUs can output 4K 60Hz (10-bit depth) at 625 MHz.
The extra 15% clock was added as a workaround for a Polaris issue
which uses DCE 11, and should not have been used on DCE 8-10 which
are already hardcoded to the highest possible display clock.
Unfortunately, the extra 15% was mistakenly copied and kept
even on code paths which don't affect Polaris.
This commit fixes that and also adds a check to make sure
not to exceed the maximum DCE 8-10 display clock.
Fixes: 8cd61c313d ("drm/amd/display: Raise dispclk value for Polaris")
Fixes: dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1ae45b5d4f)
The extra 15% clock was added as a workaround for a Polaris issue
which uses DCE 11, and should not have been used on DCE 6 which
is already hardcoded to the highest possible display clock.
Unfortunately, the extra 15% was mistakenly copied and kept
even on code paths which don't affect Polaris.
This commit fixes that and also adds a check to make sure
not to exceed the maximum DCE 6 display clock.
Fixes: 8cd61c313d ("drm/amd/display: Raise dispclk value for Polaris")
Fixes: dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
Fixes: 3ecb3b794e ("drm/amd/display: dc/clk_mgr: add support for SI parts (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 427980c1cb)
Cc: stable@vger.kernel.org
Apparently, both DCE 6.0 and 6.4 have 3 PLLs, but PLL0 can only
be used for DP. Make sure to initialize the correct amount of PLLs
in DC for these DCE versions and use PLL0 only for DP.
Also, on DCE 6.0 and 6.4, the PLL0 needs to be powered on at
initialization as opposed to DCE 6.1 and 7.x which use a different
clock source for DFS.
The following functions were used as reference from the old
radeon driver implementation of DCE 6.x:
- radeon_atom_pick_pll
- atombios_crtc_set_disp_eng_pll
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 35222b5934)
Cc: stable@vger.kernel.org
SmartMux is a mechanism to switch the GPU being used for scanout in a
hybrid configuration. This is used for devices with an eDP and two GPUs.
This is only valid when the system has a physical switch (Multiplexer)
in the board to switch between the two GPUs.
When a graphically intensive workload like a game is being run, the
system can be switch the active display to the dGPU, so that we can
avoid copying the buffer from dGPU to APU for scanout. This helps with
latency and FPS. When power consumption is preferred, the system can be
switched to the APU.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC block level should only be responsible for reporting single DSC
instance capabilities. Factoring in ODM combine requirements should be
handled in dc_dsc.c. Both components should acquire clocks from clk_mgr
to determine throughput capabilities instead of relying on hard coded
values as these can differ by SoC and SKU.
[HOW]
1) Add dsc_get_single_enc_caps to acquire single DSC instance
capabilities (replacing dsc_get_enc_caps), factoring in DSCCLK
2) add build_dsc_enc_caps to combine single DSC instance capabilities
3) account for max pixel rate per pipe (DISPCLK) when calculating
minimum slice count
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
rn_vbios_smu_set_dprefclk() was added in 2019 by
commit 4edb6fc918 ("drm/amd/display: Add Renoir clock manager")
rv1_vbios_smu_set_dprefclk() was also added in 2019 by
commit dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
neither have been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to very small clock register delta between DCN35 and DCN351, clock
spread is being checked on the wrong register for DCN351, causing the
display driver to believe that DPREFCLK downspread to be disabled when
in some stacks it is enabled. This causes the clock values for audio to
be incorrect.
[How]
Both DCN351 and DCN35 use the same clk_mgr, so we modify the DCN35
function that checks for SSC enable to read CLK6 instead of CLK5 when
using DCN351. This allows us to read for DPREFCLK downspread correctly
so the clock can properly compensate when setting values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Kevin Gao <kevin.gao3@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Eric Yang <eric.yang@amd.com>
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
dp_is_128b_132b_signal dereferences pipe->stream so it is necessary to
check it in advance.
Also fix erroneous spaces and move a variable declaration to top.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should never apply a minimum dispclk value while in prepare_bandwidth
or while displays are active. This is always an optimization for when
all displays are disabled.
[How]
Defer dispclk optimization until safe_to_lower = true and display_count
reaches 0.
Since 0 has a special value in this logic (ie. no dispclk required)
we also need adjust the logic that clamps it for the actual request
to PMFW.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On entering/exiting idle power, certain parameters would be
very useful to know for power profiling purposes.
[HOW]
This commit adds certain hard min clocks and pipe types
to log output on idle optimization enter/exit.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Sung Lee <Sung.Lee@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When effective bandwidth from the SoC is enough to perform SubVP
prefetchs, then DF throttling is not required.
[HOW]
Provide SMU the required clocks for which DF throttling is not required.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver reports 0 display when the virtual display is still present, and
causes P-state hang in FW.
[HOW]
When enumerating through streams, check for active planes and use that
to indicate number of displays.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting min dispclk to 50Mhz outside clock lowering function causes
unnecessary calls to SMU to lower dispclk and causes dentist hangs when
there is no stream on the pipes.
[How]
Move the set minimum dispclk logic inside the lowering dispclk if
statement.
Fixes: 2344413205 ("DCN35 set min dispclk to 50Mhz")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Skipping clock updates is not a hard requirement for overclocking
and only an optimization. Remove the skip as this can cause issues
for FAMS transitions during the overclock sequence. If FAMS
is enabled we must disable UCLK switch on any full update (which
requires update clocks to be called).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
immediate_disable_crtc does not reset ODM. if switching to disable_crtc
which will disable ODM as well. i.e. need to restore ODM mem cfg at
reenable it at end of w/a.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as dc->clk_mgr, are null checked previously in the same
function, so Coverity warns "implies that "dc->clk_mgr" might be null".
As a result, these pointers need to be checked when used again.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is a workaround for an dcn3.1 hang that happens if otg dispclk
is ramped while otg is on and stream enc is off.
But this w/a should not trigger when we have a dig active.
[How]
Avoid disable otg when dig FE/BE FIFO was not switched.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Jingwen Zhu <jingwen.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
