Make video port registers nonvolatile. As DSP_CTRL register is written
to twice due to gamma LUT enable bit which is set outside of the main
DSP_CTRL initialization within atomic_enable (for rk356x case it is also
necessary to always disable gamma LUT before writing a new LUT) there is
a chance that DSP_CTRL value read-out in gamma LUT init/update code is
not the one which was written by the preceding DSP_CTRL initialization
code within atomic_enable. This might result in misconfigured DSP_CTRL
which leads to no visual output[1]. Since DSP_CTRL write takes effect
after VSYNC[1] the issue is not always present. When tested on Pinetab2
with kernel 6.14 it happenes only when DRM is compiled as a module[1].
In order to confirm that it is a timing issue I inserted 18ms udelay
before vop2_crtc_atomic_try_set_gamma in atomic enable and compiled DRM
as module - this has also fixed the issue.
[1] https://lore.kernel.org/linux-rockchip/562b38e5.a496.1975f09f983.Coremail.andyshrk@163.com/
Reported-by: Diederik de Haas <didi.debian@cknow.org>
Closes: https://lore.kernel.org/linux-rockchip/DAEVDSTMWI1E.J454VZN0R9MA@cknow.org/
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Piotr Zalewski <pZ010001011111@proton.me>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250706083629.140332-2-pZ010001011111@proton.me
In some application scenarios, we hope to get the corresponding
connector when the bridge's detect hook is invoked.
In most cases, we can get the connector by drm_atomic_get_connector_for_encoder
if the encoder attached to the bridge is enabled, however there will
still be some scenarios where the detect hook of the bridge is called
but the corresponding encoder has not been enabled yet. For instance,
this occurs when the device is hot plug in for the first time.
Since the call to bridge's detect is initiated by the connector, passing
down the corresponding connector directly will make things simpler.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250703125027.311109-3-andyshrk@163.com
[DB: added the chunk to the cdn-dp driver]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The all video ports of rk3568/rk3588 share the same OVL_LAYER_SEL
and OVL_PORT_SEL registers, and the configuration of these two registers
can be set to take effect when the vsync signal arrives at a certain Video
Port.
If two threads for two display output choose to update these two registers
simultaneously to meet their own plane adjustment requirements(change plane
zpos or switch plane from one crtc to another), then no matter which Video
Port'svsync signal we choose to follow for these two registers, the display
output of the other Video Port will be abnormal.
This is because the configuration of this Video Port does not take
effect at the right time (its configuration should take effect when its
VSYNC signal arrives).
In order to solve this problem, when performing plane migration or
change the zpos of planes, there are two things to be observed and
followed:
1. When a plane is migrated from one VP to another, the configuration of
the layer can only take effect after the Port mux configuration is
enabled.
2. When change the zpos of planes, we must ensure that the change for
the previous VP takes effect before we proceed to change the next VP.
Otherwise, the new configuration might overwrite the previous one for
the previous VP, or it could lead to the configuration of the previous
VP being take effect along with the VSYNC of the new VP.
This issue only occurs in scenarios where multi-display output is enabled.
Fixes: c5996e4ab1 ("drm/rockchip: vop2: Make overlay layer select register configuration take effect by vsync")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250421102156.424480-1-andyshrk@163.com
This function not only configure hardware reset register, but also
do some other configurations. Therefore, it is more appropriate to
name it inno_hdmi_init_hw, which will also facilitate the addition
of other functions to this function in the following patch.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-5-andyshrk@163.com
Convert it to drm bridge driver, it will be convenient for us to
migrate the connector part to the display driver later.
Considering that some code depend on the connector, the following
changes have been made:
- Only process edid in &drm_bridge_funcs.edid_read(), so no need to
store additional edid info.
- Now cdn_dp_get_sink_capability() only focused on reading DPCD_REV.
- Update bpc info in cdn_dp_bridge_atomic_enable() instead of
cdn_dp_encoder_mode_set(). Actually, the bpc data will be used in
cdn_dp_bridge_atomic_enable().
- Switch to use DRM_BRIDGE_OP_DP_AUDIO helpers.
This patch also convert to use devm_drm_bridge_alloc() API.
Tested with RK3399 EVB IND board.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250529071334.441-1-kernel@airkyi.com
Each window of a vop2 is usable by a specific set of video ports, so while
binding the vop2, we look through the list of available windows trying to
find one designated as primary-plane and usable by that specific port.
The code later wants to use drm_crtc_init_with_planes with that found
primary plane, but nothing has checked so far if a primary plane was
actually found.
For whatever reason, the rk3576 vp2 does not have a usable primary window
(if vp0 is also in use) which brought the issue to light and ended in a
null-pointer dereference further down.
As we expect a primary-plane to exist for a video-port, add a check at
the end of the window-iteration and fail probing if none was found.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250610212748.1062375-1-heiko@sntech.de
In the function drm_gem_fb_init_with_funcs, the framebuffer (fb)
and its corresponding object ID have already been registered.
So we need to cleanup the drm framebuffer if the subsequent
execution of drm_gem_fb_afbc_init fails.
Directly call drm_framebuffer_put to ensure that all fb related
resources are cleanup.
Fixes: 7707f7227f ("drm/rockchip: Add support for afbc")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250509031607.2542187-1-andyshrk@163.com
The HSYNC/VSYNC polarity of rk3036 HDMI are controlled by GRF.
Without the polarity configuration in GRF, it can be observed
from the HDMI protocol analyzer that the H/V front/back timing
output by RK3036 HDMI are currently not in line with the specifications.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250422070455.432666-5-andyshrk@163.com
DRM_DISPLAY_DP_AUX_BUS cannot be selected when CONFIG_OF is disabled:
WARNING: unmet direct dependencies detected for DRM_DISPLAY_DP_AUX_BUS
Depends on [n]: HAS_IOMEM [=y] && DRM [=y] && OF [=n]
Selected by [y]:
- DRM_ROCKCHIP [=y] && HAS_IOMEM [=y] && DRM [=y] && ROCKCHIP_IOMMU [=y] && ROCKCHIP_ANALOGIX_DP [=y]
Rockchip platforms all depend on OF anyway, so add the dependency here
for compile testing.
Fixes: d7b4936b2b ("drm/rockchip: analogix_dp: Add support to get panel from the DP AUX bus")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250423164422.2793634-1-arnd@kernel.org
RK3588 integrates the Analogix eDP 1.3 TX controller IP and the HDMI/eDP
TX Combo PHY based on a Samsung IP block. There are also two independent
eDP display interface with different address on RK3588 Soc.
The patch currently adds only the basic support, specifically RGB output
up to 4K@60Hz, without the tests for audio, PSR and other eDP 1.3 specific
features.
In additon, the above Analogix IP has always been utilized as eDP on
Rockchip platform, despite its capability to also support the DP v1.2.
Therefore, the newly added logs will contain the term 'edp' rather than
'dp'. And the newly added 'apb' reset control is to ensure the APB bus
of eDP controller works well on the RK3588 SoC.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-12-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Move drm_of_find_panel_or_bridge() a little later and combine it with
component_add() into a new function rockchip_dp_link_panel(). The function
will serve as done_probing() callback of devm_of_dp_aux_populate_bus(),
aiding to support for obtaining the eDP panel via the DP AUX bus.
If failed to get the panel from the DP AUX bus, it will then try the other
way to get panel information through the platform bus.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250310104114.2608063-9-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Because the layer/window enable/disable is take effect by vsync, if the
overlay configuration of these layers does not follow vsync and
takes effect immediately instead, when multiple layers are dynamically
enable/disable, inconsistent display contents may be seen on the screen.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250318062024.4555-1-andyshrk@163.com
Commit 52d11c863a ("drm/rockchip: lvds: do not print scary message when
probing defer") already started hiding scary messages that are not relevant
if the requested supply just returned EPROBE_DEFER, but there are more
possible sources - like the phy.
So modernize the whole logging in the probe path by replacing the
remaining deprecated DRM_DEV_ERROR with appropriate dev_err(_probe)
and drm_err calls.
The distinction here is that all messages talking about mishaps of the
lvds element use dev_err(_probe) while messages caused by interaction
with the main Rockchip drm-device use drm_err.
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250304124418.111061-3-heiko@sntech.de
The LVDS block needs a separate pclk only on some socs, so currently
requests and prepares it in the soc-specific probe function, but common
code is required to unprepare it in the error path or on driver remove.
While this works because clk_unprepare just does nothing if clk is NULL,
this mismatch of who is responsible still is not very nice.
The clock-framework already has a helper for clk-get-and-prepare even
with devres support in devm_clk_get_prepared().
This will get and prepare the clock and also unprepare it on driver
removal, saving the driver from having to handle it "manually".
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250304124418.111061-2-heiko@sntech.de
When the drm-driver probes, it mainly creates the component device, where
all the sub-drivers (vops, hdmi, etc) hook into.
This will cause the shutdown handler to get called on shutdown, even
though the drm-device might not have been set up, or the component bind
might have failed.
So use the new component helper to check whether the drm-device is up
and only then call the drm-atomic helper to release all the drm magic.
This prevents failures when the drm-device is never set, or has been
freed up already for example by a probe-defer during the component bind.
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250220234141.2788785-3-heiko@sntech.de
