On LNL+ for a disconnected sink the pin assignment value gets cleared by
the HW/FW as soon as the sink gets disconnected, even if the PHY
ownership got acquired already by the BIOS/driver (and hence the PHY
itself is still connected and used by the display). During HW readout
this can result in detecting the PHY's max lane count as 0 - matching
the above cleared aka NONE pin assignment HW state. For a connected PHY
the driver in general (outside of intel_tc.c) expects the max lane count
value to be valid for the video mode enabled on the corresponding output
(1, 2 or 4). Ensure this by setting the max lane count to 4 in this
case. Note, that it doesn't matter if this lane count happened to be
more than the max lane count with which the PHY got connected and
enabled, since the only thing the driver can do with such an output -
where the DP-alt sink is disconnected - is to disable the output.
v2: Rebased on change reading out the pin configuration only if the PHY
is connected.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-4-imre.deak@intel.com
(cherry picked from commit 33cf70bc0f)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
The PHY's pin assignment value in the TCSS_DDI_STATUS register - as set
by the HW/FW based on the connected DP-alt sink's TypeC/PD pin
assignment negotiation - gets cleared by the HW/FW on LNL+ as soon as
the sink gets disconnected, even if the PHY ownership got acquired
already by the driver (and hence the PHY itself is still connected and
used by the display). This is similar to how the PHY Ready flag gets
cleared on LNL+ in the same register.
To be able to query the max lane count value on LNL+ - which is based on
the above pin assignment - at all times even after the sink gets
disconnected, the max lane count must be determined and cached during
the PHY's HW readout and connect sequences. Do that here, leaving the
actual use of the cached value to a follow-up change.
v2: Don't read out the pin configuration if the PHY is disconnected.
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-3-imre.deak@intel.com
(cherry picked from commit 3e32438fc4)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
The TypeC PHY HW readout during driver loading and system resume
determines which TypeC mode the PHY is in (legacy/DP-alt/TBT-alt) and
whether the PHY is connected, based on the PHY's Owned and Ready flags.
For the PHY to be in DP-alt or legacy mode and for the PHY to be in the
connected state in these modes, both the Owned (set by the BIOS/driver)
and the Ready (set by the HW) flags should be set.
On ICL-MTL the HW kept the PHY's Ready flag set after the driver
connected the PHY by acquiring the PHY ownership (by setting the Owned
flag), until the driver disconnected the PHY by releasing the PHY
ownership (by clearing the Owned flag). On LNL+ this has changed, in
that the HW clears the Ready flag as soon as the sink gets disconnected,
even if the PHY ownership was acquired already and hence the PHY is
being used by the display.
When inheriting the HW state from BIOS for a PHY connected in DP-alt
mode on which the sink got disconnected - i.e. in a case where the sink
was connected while BIOS/GOP was running and so the sink got enabled
connecting the PHY, but the user disconnected the sink by the time the
driver loaded - the PHY Owned but not Ready state must be accounted for
on LNL+ according to the above. Do that by assuming on LNL+ that the PHY
is connected in DP-alt mode whenever the PHY Owned flag is set,
regardless of the PHY Ready flag.
This fixes a problem on LNL+, where the PHY TypeC mode / connected state
was detected incorrectly for a DP-alt sink, which got connected and then
disconnected by the user in the above way.
v2: Rename tc_phy_in_legacy_or_dp_alt_mode() to tc_phy_owned_by_display().
(Luca, Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
[Imre: Add one-liner function documentation for tc_phy_owned_by_display()]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250811080152.906216-2-imre.deak@intel.com
(cherry picked from commit 89f4b196ee)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Using device_find_child() and of_find_device_by_node() to locate
devices could cause an imbalance in the device's reference count.
device_find_child() and of_find_device_by_node() both call
get_device() to increment the reference count of the found device
before returning the pointer. In mtk_drm_get_all_drm_priv(), these
references are never released through put_device(), resulting in
permanent reference count increments. Additionally, the
for_each_child_of_node() iterator fails to release node references in
all code paths. This leaks device node references when loop
termination occurs before reaching MAX_CRTC. These reference count
leaks may prevent device/node resources from being properly released
during driver unbind operations.
As comment of device_find_child() says, 'NOTE: you will need to drop
the reference with put_device() after use'.
Cc: stable@vger.kernel.org
Fixes: 1ef7ed4835 ("drm/mediatek: Modify mediatek-drm for mt8195 multi mmsys support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250812071932.471730-1-make24@iscas.ac.cn/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In 32-bit arm, the build fails with:
error[E0308]: mismatched types
--> drivers/gpu/drm/nova/file.rs:42:28
|
42 | getparam.set_value(value);
| --------- ^^^^^ expected `u64`, found `u32`
| |
| arguments to this method are incorrect
|
note: method defined here
--> drivers/gpu/drm/nova/uapi.rs:29:12
|
29 | pub fn set_value(&self, v: u64) {
| ^^^^^^^^^ ------
help: you can convert a `u32` to a `u64`
|
42 | getparam.set_value(value.into());
| +++++++
The reason is that `Getparam::set_value` takes a `u64` (from the UAPI),
but `pci::Device::resource_len()` returns a `resource_size_t`, which is a
`phys_addr_t`, which may be 32- or 64-bit.
Thus add an `into()` call to support the 32-bit case, while allowing the
Clippy lint that complains in the 64-bit case where the type is the same.
Fixes: cdeaeb9dd7 ("drm: nova-drm: add initial driver skeleton")
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Christian Schrefl <chrisi.schrefl@gmail.com>
Link: https://lore.kernel.org/r/20250724165441.2105632-1-ojeda@kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
devm_drm_bridge_alloc() returns ERR_PTR on failure instead of a
NULL pointer, so use IS_ERR() to check the returned pointer.
While at it, on failure, return ERR_CAST(dp) instead of
ERR_PTR(-ENOMEM) in order not to depend on devm_drm_bridge_alloc()
error code implementation.
Fixes: 48f05c3b4b ("drm/bridge: analogix_dp: Use devm_drm_bridge_alloc() API")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20250806095224.527938-1-victor.liu@nxp.com
LMEM is partitioned between multiple VFs and we expect that the more
VFs we have, the less LMEM is assigned to each VF.
This means that we can achieve full LMEM BAR access without the need to
attempt full VF LMEM BAR resize via pci_resize_resource().
Always try to set the largest possible BAR size that allows to fit the
number of enabled VFs and inform the user in case the resize attempt is
not successful.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250527120637.665506-7-michal.winiarski@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 32a4d1b98e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since commit c9b1150a68 ("drm/atomic-helper: Re-order bridge chain
pre-enable and post-disable"), the bridge pre_enable callbacks are now
called before crtc enable, and the bridge post_disable callbacks after
the crtc disable.
In the mediatek-drm driver, this change leads to transfer errors on
mtk_dsi_host_transfer callback processing during the panel bridge
pre-enable sequence because the DSI host bridge pre_enable and CRTC
enable sequences, that are enabling the required clocks and PHY using
mtk_dsi_poweron function, are called after.
So, in order to fix this call order issue, request the DSI host bridge
be pre-enabled before panel bridge by setting pre_enable_prev_first
flag on DSI device bridge in the mtk_dsi_host_attach function.
Fixes: c9b1150a68 ("drm/atomic-helper: Re-order bridge chain pre-enable and post-disable")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250701-mediatek-drm-fix-dsi-panel-init-v1-1-7af4adb9fdeb@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Make video port registers nonvolatile. As DSP_CTRL register is written
to twice due to gamma LUT enable bit which is set outside of the main
DSP_CTRL initialization within atomic_enable (for rk356x case it is also
necessary to always disable gamma LUT before writing a new LUT) there is
a chance that DSP_CTRL value read-out in gamma LUT init/update code is
not the one which was written by the preceding DSP_CTRL initialization
code within atomic_enable. This might result in misconfigured DSP_CTRL
which leads to no visual output[1]. Since DSP_CTRL write takes effect
after VSYNC[1] the issue is not always present. When tested on Pinetab2
with kernel 6.14 it happenes only when DRM is compiled as a module[1].
In order to confirm that it is a timing issue I inserted 18ms udelay
before vop2_crtc_atomic_try_set_gamma in atomic enable and compiled DRM
as module - this has also fixed the issue.
[1] https://lore.kernel.org/linux-rockchip/562b38e5.a496.1975f09f983.Coremail.andyshrk@163.com/
Reported-by: Diederik de Haas <didi.debian@cknow.org>
Closes: https://lore.kernel.org/linux-rockchip/DAEVDSTMWI1E.J454VZN0R9MA@cknow.org/
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Piotr Zalewski <pZ010001011111@proton.me>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250706083629.140332-2-pZ010001011111@proton.me
Introduce error handling to address an issue where, after a hotplug
event, the cursor continues to update. This situation can lead to a
kernel panic due to accessing the NULL `old_state->crtc`.
E,g.
Unable to handle kernel NULL pointer dereference at virtual address
Call trace:
mtk_crtc_plane_disable+0x24/0x140
mtk_plane_atomic_update+0x8c/0xa8
drm_atomic_helper_commit_planes+0x114/0x2c8
drm_atomic_helper_commit_tail_rpm+0x4c/0x158
commit_tail+0xa0/0x168
drm_atomic_helper_commit+0x110/0x120
drm_atomic_commit+0x8c/0xe0
drm_atomic_helper_update_plane+0xd4/0x128
__setplane_atomic+0xcc/0x110
drm_mode_cursor_common+0x250/0x440
drm_mode_cursor_ioctl+0x44/0x70
drm_ioctl+0x264/0x5d8
__arm64_sys_ioctl+0xd8/0x510
invoke_syscall+0x6c/0xe0
do_el0_svc+0x68/0xe8
el0_svc+0x34/0x60
el0t_64_sync_handler+0x1c/0xf8
el0t_64_sync+0x180/0x188
Adding NULL pointer checks to ensure stability by preventing operations
on an invalid CRTC state.
Fixes: d208261e9f ("drm/mediatek: Add wait_event_timeout when disabling plane")
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20250728025036.24953-1-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
After a recent change in clang to expose uninitialized warnings from
const variables and pointers [1], there is a warning around crtc_state
in dpu_plane_virtual_atomic_check():
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:1145:6: error: variable 'crtc_state' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
1145 | if (plane_state->crtc)
| ^~~~~~~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:1149:58: note: uninitialized use occurs here
1149 | ret = dpu_plane_atomic_check_nosspp(plane, plane_state, crtc_state);
| ^~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:1145:2: note: remove the 'if' if its condition is always true
1145 | if (plane_state->crtc)
| ^~~~~~~~~~~~~~~~~~~~~~
1146 | crtc_state = drm_atomic_get_new_crtc_state(state,
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:1139:35: note: initialize the variable 'crtc_state' to silence this warning
1139 | struct drm_crtc_state *crtc_state;
| ^
| = NULL
Initialize crtc_state to NULL like other places in the driver do, so
that it is consistently initialized.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/2106
Fixes: 774bcfb731 ("drm/msm/dpu: add support for virtual planes")
Link: 2464313eef [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently, the high bitfield of certain DSI registers
do not align with the configuration of the SWI registers
description. This can lead to wrong programming these DSI
registers, for example for 4k resloution where H_TOTAL is
taking 13 bits but software is programming only 12 bits
because of the incorrect bitmask for H_TOTAL bitfeild,
this is causing DSI FIFO errors. To resolve this issue,
increase the high bitfield of the DSI registers from 12 bits
to 16 bits in dsi.xml to match the SWI register configuration.
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Fixes: 4f52f5e63b ("drm/msm: import XML display registers database")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/666229/
Link: https://lore.kernel.org/r/20250730123938.1038640-1-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
To configure and enable the DSI PHY PLL clocks, the MDSS AHB clock must
be active for MMIO operations. Typically, this AHB clock is enabled as
part of the DSI PHY interface enabling (dsi_phy_enable_resource).
However, since these PLL clocks are registered as clock entities, they
can be enabled independently of the DSI PHY interface, leading to
enabling failures and subsequent warnings:
```
msm_dsi_phy 5e94400.phy: [drm:dsi_pll_14nm_vco_prepare] *ERROR* DSI PLL lock failed
------------[ cut here ]------------
dsi0pllbyte already disabled
WARNING: CPU: 3 PID: 1 at drivers/clk/clk.c:1194 clk_core_disable+0xa4/0xac
CPU: 3 UID: 0 PID: 1 Comm: swapper/0 Tainted:
Tainted: [W]=WARN
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[...]
```
This issue is particularly prevalent at boot time during the disabling of
unused clocks (clk_disable_unused()) which includes enabling the parent
clock(s) when CLK_OPS_PARENT_ENABLE flag is set (this is the case for the
14nm DSI PHY PLL consumers).
To resolve this issue, we move the AHB clock as a PM dependency of the DSI
PHY device (via pm_clk). Since the DSI PHY device is the parent of the PLL
clocks, this resolves the PLL/AHB dependency. Now the AHB clock is enabled
prior the PLL clk_prepare callback, as part of the runtime-resume chain.
We also eliminate dsi_phy_[enable|disable]_resource functions, which are
superseded by runtime PM.
Note that it breaks compatibility with kernels before 6.0, as we do not
support anymore the legacy `iface_clk` name.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/663239/
Link: https://lore.kernel.org/r/20250709140836.124143-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
This reverts commit 515986100d.
The dma_buf field in struct drm_gem_object is not stable over the
object instance's lifetime. The field becomes NULL when user space
releases the final GEM handle on the buffer object. This resulted
in a NULL-pointer deref.
Workarounds in commit 5307dce878 ("drm/gem: Acquire references on
GEM handles for framebuffers") and commit f6bfc9afc7 ("drm/framebuffer:
Acquire internal references on GEM handles") only solved the problem
partially. They especially don't work for buffer objects without a DRM
framebuffer associated.
Hence, this revert to going back to using .import_attach->dmabuf.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Simona Vetter <simona.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250715082635.34974-1-tzimmermann@suse.de
During process kill, drm_sched_entity_flush() will kill the vm
entities. The following job submissions of this process will fail, and
the resources of these jobs have not been released, nor have the fences
been signalled, causing tasks to hang and timeout.
Fix by check entity status in amdgpu_vm_ready() and avoid submit jobs to
stopped entity.
v2: add amdgpu_vm_ready() check before amdgpu_vm_clear_freed() in
function amdgpu_cs_vm_handling().
Fixes: 1f02f2044b ("drm/amdgpu: Avoid extra evict-restore process.")
Signed-off-by: Liu01 Tong <Tong.Liu01@amd.com>
Signed-off-by: Lin.Cao <lincao12@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f101c13a87)
It should use vm flags instead of pte flags
to specify bo vm attributes.
Fixes: 7946340fa3 ("drm/amdgpu: Move csa related code to separate file")
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b08425fa77)
The vram block allocation flag must be cleared
before making vram reservation, otherwise reserving
addresses within the currently freed memory range
will always fail.
Fixes: c9cad937c0 ("drm/amdgpu: add drm buddy support to amdgpu")
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d38eaf27de)
The fw reserved GFX command is only supported starting from PSP fw
version 0x3a0e14 and 0x3b0e0d. Older versions do not support this command.
Add a version guard to ensure the command is only used when the running
PSP fw meets the minimum version requirement.
This ensures backward compatibility and safe operation across fw
revisions.
Fixes: a3b7f9c306 ("drm/amdgpu: reclaim psp fw reservation memory region")
Signed-off-by: Frank Min <Frank.Min@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 065e23170a)
Clamp writes to power limits powerX_crit/currX_crit, powerX_cap,
powerX_max, to the maximum supported by the pcode mailbox
when sysfs-provided values exceed this limit.
Although the pcode already performs clamping, values beyond the pcode
mailbox's supported range get truncated, leading to incorrect
critical power settings.
This patch ensures proper clamping to prevent such truncation.
v2:
- Address below review comments. (Riana)
- Split comments into multiple sentences.
- Use local variables for readability.
- Add a debug log.
- Use u64 instead of unsigned long.
v3:
- Change drm_dbg logs to drm_info. (Badal)
v4:
- Rephrase the drm_info log. (Rodrigo, Riana)
- Rename variable max_mbx_power_limit to max_supp_power_limit, as
limit is same for platforms with and without mailbox power limit
support.
Signed-off-by: Karthik Poosa <karthik.poosa@intel.com>
Fixes: 92d44a422d ("drm/xe/hwmon: Expose card reactive critical power")
Fixes: fb1b70607f ("drm/xe/hwmon: Expose power attributes")
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Link: https://lore.kernel.org/r/20250808185310.3466529-1-karthik.poosa@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit d301eb950d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
With non-page aligned copy, we need to use 4 byte aligned pitch, however
the size itself might still be close to our maximum of ~8M, and so the
dimensions of the copy can easily exceed the S16_MAX limit of the copy
command leading to the following assert:
xe 0000:03:00.0: [drm] Assertion `size / pitch <= ((s16)(((u16)~0U) >> 1))` failed!
platform: BATTLEMAGE subplatform: 1
graphics: Xe2_HPG 20.01 step A0
media: Xe2_HPM 13.01 step A1
tile: 0 VRAM 10.0 GiB
GT: 0 type 1
WARNING: CPU: 23 PID: 10605 at drivers/gpu/drm/xe/xe_migrate.c:673 emit_copy+0x4b5/0x4e0 [xe]
To fix this account for the pitch when calculating the number of current
bytes to copy.
Fixes: 270172f64b ("drm/xe: Update xe_ttm_access_memory to use GPU for non-visible access")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://lore.kernel.org/r/20250731093807.207572-7-matthew.auld@intel.com
(cherry picked from commit 8c2d61e0e9)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If the buf + offset is not aligned to XE_CAHELINE_BYTES we fallback to
using a bounce buffer. However the bounce buffer here is allocated on
the stack, and the only alignment requirement here is that it's
naturally aligned to u8, and not XE_CACHELINE_BYTES. If the bounce
buffer is also misaligned we then recurse back into the function again,
however the new bounce buffer might also not be aligned, and might never
be until we eventually blow through the stack, as we keep recursing.
Instead of using the stack use kmalloc, which should respect the
power-of-two alignment request here. Fixes a kernel panic when
triggering this path through eudebug.
v2 (Stuart):
- Add build bug check for power-of-two restriction
- s/EINVAL/ENOMEM/
Fixes: 270172f64b ("drm/xe: Update xe_ttm_access_memory to use GPU for non-visible access")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://lore.kernel.org/r/20250731093807.207572-6-matthew.auld@intel.com
(cherry picked from commit 38b34e928a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We want to get rid of triggering "Frame Change" events from
frontbuffer flush calls. We are about to move using TRANS_PUSH
register for this on LunarLake and onwards. Touching TRANS_PUSH
register from fronbuffer flush would be problematic as it's written by
DSB as well.
Fix this by using intel_psr_exit when flush or invalidate is done on
LunarLake and onwards. This is not possible on AlderLake and
MeteorLake due to HW bug in PSR2 disable.
This patch is also fixing problems with cursor plane where cursor is
disappearing or duplicate cursor is seen on the screen.
v2: Commit message updated
Bspec: 68927, 68934, 66624
Reported-by: Janna Martl <janna.martl109@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/5522
Fixes: 411ad63877 ("drm/i915/psr: Use SFF_CTL on invalidate/flush for LunarLake onwards")
Tested-by: Janna Martl <janna.martl109@gmail.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250801062905.564453-1-jouni.hogander@intel.com
(cherry picked from commit 46fb38cb20)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
As per the wa_18038517565, we need to disable FBC compressor
clock gating before enabling FBC and enable after disabling
FBC. Placing the enabling of clock gating in the fbc deactivate
function can make the above wa logic go wrong in case of
frontbuffer rendering FBC mechanism. FBC deactivate can get
called during fb invalidate and then the corresponding FBC
activate can get called without properly disabling the clock
gating and can result in compression stalled. So move the
enable clock gating at the end of one FBC session after FBC
is completely disabled for a pipe.
Bspec: 74212, 72197, 69741, 65555
Fixes: 010363c461 ("drm/i915/display: implement wa_18038517565")
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://lore.kernel.org/r/20250729124648.288497-1-vinod.govindapillai@intel.com
(cherry picked from commit 82dde0407a)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Pull gpio updates from Bartosz Golaszewski:
"As discussed: there's a small commit that removes the legacy GPIO line
value setter callbacks as they're no longer used and a big, treewide
commit that renames the new ones to the old names across all GPIO
drivers at once.
While at it: there are also two fixes that I picked up over the course
of the merge window:
- remove unused, legacy GPIO line value setters from struct gpio_chip
- rename the new set callbacks back to the original names treewide
- fix interrupt handling in gpio-mlxbf2
- revert a buggy immutable irqchip conversion"
* tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
treewide: rename GPIO set callbacks back to their original names
gpio: remove legacy GPIO line value setter callbacks
gpio: mlxbf2: use platform_get_irq_optional()
Revert "gpio: pxa: Make irq_chip immutable"
Pull drm fixes from Dave Airlie:
"This is the fixes that built up in the merge window, mostly amdgpu and
xe with one i915 display fix, seems like things are pretty good for
rc1.
i915:
- DP LPFS fixes
xe:
- SRIOV: PF fixes and removal of need of module param
- Fix driver unbind around Devcoredump
- Mark xe driver as BROKEN if kernel page size is not 4kB
amdgpu:
- GC 9.5.0 fixes
- SMU fix
- DCE 6 DC fixes
- mmhub client ID fixes
- VRR fix
- Backlight fix
- UserQ fix
- Legacy reset fix
- Misc fixes
amdkfd:
- CRIU fix
- Debugfs fix"
* tag 'drm-next-2025-08-08' of https://gitlab.freedesktop.org/drm/kernel: (28 commits)
drm/amdgpu: add missing vram lost check for LEGACY RESET
drm/amdgpu/discovery: fix fw based ip discovery
drm/amdkfd: Destroy KFD debugfs after destroy KFD wq
amdgpu/amdgpu_discovery: increase timeout limit for IFWI init
drm/amdgpu: Update SDMA firmware version check for user queue support
drm/amdgpu: Add NULL check for asic_funcs
drm/amd/display: Revert "drm/amd/display: Fix AMDGPU_MAX_BL_LEVEL value"
drm/amd/display: fix a Null pointer dereference vulnerability
drm/amd/display: Add primary plane to commits for correct VRR handling
drm/amdgpu: update mmhub 3.3 client id mappings
drm/amdgpu: update mmhub 3.0.1 client id mappings
drm/amdgpu: Retain job->vm in amdgpu_job_prepare_job
drm/amd/display: Fix DCE 6.0 and 6.4 PLL programming.
drm/amd/display: Don't overwrite dce60_clk_mgr
drm/amdkfd: Fix checkpoint-restore on multi-xcc
drm/amd: Restore cached manual clock settings during resume
drm/amd: Restore cached power limit during resume
drm/amdgpu: Update external revid for GC v9.5.0
drm/amdgpu: Update supported modes for GC v9.5.0
Mark xe driver as BROKEN if kernel page size is not 4kB
...
