The HW resource reservation logic allows the L2 driver to use the
RoCE resources if the RoCE driver is not registered. When calculating
the stats contexts available for L2, we should not blindly subtract
the stats contexts reserved for RoCE unless the RoCE driver is
registered. This bug may cause the L2 rings to be less than the
number requested when we are close to running out of stats contexts.
Fixes: 2e4592dc9b ("bnxt_en: Change MSIX/NQs allocation policy")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before we accept an ethtool request to increase a resource (such as
rings), we call the FW to check that the requested resource is likely
available first before we commit. But it is still possible that
the actual reservation or allocation can fail. The existing code
is missing the logic to adjust the TX rings in case the reserved
TX rings are less than requested. Add a warning message (a similar
message for RX rings already exists) and add the logic to adjust
the TX rings. Without this fix, the number of TX rings reported
to the stack can exceed the actual TX rings and ethtool -l will
report more than the actual TX rings.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The data page pool always fills the HW rx ring with pages. On arm64 with
64K pages, this will waste _at least_ 32K of memory per entry in the rx
ring.
Fix by fragmenting the pages if PAGE_SIZE > BNXT_RX_PAGE_SIZE. This
makes the data page pool the same as the header pool.
Tested with iperf3 with a small (64 entries) rx ring to encourage buffer
circulation.
Fixes: cd1fafe7da ("eth: bnxt: add support rx side device memory TCP")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250812182907.1540755-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Page pool can have pages "directly" (locklessly) recycled to it,
if the NAPI that owns the page pool is scheduled to run on the same CPU.
To make this safe we check that the NAPI is disabled while we destroy
the page pool. In most cases NAPI and page pool lifetimes are tied
together so this happens naturally.
The queue API expects the following order of calls:
-> mem_alloc
alloc new pp
-> stop
napi_disable
-> start
napi_enable
-> mem_free
free old pp
Here we allocate the page pool in ->mem_alloc and free in ->mem_free.
But the NAPIs are only stopped between ->stop and ->start. We created
page_pool_disable_direct_recycling() to safely shut down the recycling
in ->stop. This way the page_pool_destroy() call in ->mem_free doesn't
have to worry about recycling any more.
Unfortunately, the page_pool_disable_direct_recycling() is not enough
to deal with failures which necessitate freeing the _new_ page pool.
If we hit a failure in ->mem_alloc or ->stop the new page pool has
to be freed while the NAPI is active (assuming driver attaches the
page pool to an existing NAPI instance and doesn't reallocate NAPIs).
Freeing the new page pool is technically safe because it hasn't been
used for any packets, yet, so there can be no recycling. But the check
in napi_assert_will_not_race() has no way of knowing that. We could
check if page pool is empty but that'd make the check much less likely
to trigger during development.
Add page_pool_enable_direct_recycling(), pairing with
page_pool_disable_direct_recycling(). It will allow us to create the new
page pools in "disabled" state and only enable recycling when we know
the reconfig operation will not fail.
Coincidentally it will also let us re-enable the recycling for the old
pool, if the reconfig failed:
-> mem_alloc (new)
-> stop (old)
# disables direct recycling for old
-> start (new)
# fail!!
-> start (old)
# go back to old pp but direct recycling is lost :(
-> mem_free (new)
The new helper is idempotent to make the life easier for drivers,
which can operate in HDS mode and support zero-copy Rx.
The driver can call the helper twice whether there are two pools
or it has multiple references to a single pool.
Fixes: 40eca00ae6 ("bnxt_en: unlink page pool when stopping Rx queue")
Tested-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250805003654.2944974-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
Pull timer cleanups from Thomas Gleixner:
"A treewide cleanup of struct cycle_counter const annotations.
The initial idea of making them const was correct as they were
seperate instances. When they got embedded into larger data
structures, which are even modified by the callback this got moot. The
only reason why this went unnoticed is that the required
container_of() casts the const attribute forcefully away.
Stop pretending that it is const"
* tag 'timers-cleanups-2025-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time/timecounter: Fix the lie that struct cyclecounter is const
On ASP versions v2.x we need to program the TX map vector register to
properly exercise end-to-end flow control, otherwise the TX engine can
either lock-up, or cause the hardware calculated checksum to be
wrong/corrupted when multiple back to back packets are being submitted
for transmission. This register defaults to 0, which means no flow
control being applied.
Fixes: e9f31435ee ("net: bcmasp: Add support for asp-v3.0")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250718212242.3447751-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.16-rc6-2).
No conflicts.
Adjacent changes:
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
c701574c54 ("wifi: mt76: mt7925: fix invalid array index in ssid assignment during hw scan")
b3a431fe2e ("wifi: mt76: mt7925: fix off by one in mt7925_mcu_hw_scan()")
drivers/net/wireless/mediatek/mt76/mt7996/mac.c
62da647a2b ("wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()")
dc66a129ad ("wifi: mt76: add a wrapper for wcid access with validation")
drivers/net/wireless/mediatek/mt76/mt7996/main.c
3dd6f67c66 ("wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl()")
8989d8e90f ("wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()")
net/mac80211/cfg.c
58fcb1b428 ("wifi: mac80211: reject VHT opmode for unsupported channel widths")
037dc18ac3 ("wifi: mac80211: add support for storing station S1G capabilities")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bnxt_ets_validate(), the code incorrectly loops over all possible
traffic classes to check and add the ETS settings. Fix it to loop
over the configured traffic classes only.
The unconfigured traffic classes will default to TSA_ETS with 0
bandwidth. Looping over these unconfigured traffic classes may
cause the validation to fail and trigger this error message:
"rejecting ETS config starving a TC\n"
The .ieee_setets() will then fail.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Reviewed-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250710213938.1959625-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Query resources from the firmware and, based on the
availability of resources, initialize the default
settings. The default settings include:
1. Rings and other resource reservations with the
firmware. This ensures that resources are reserved
before network and auxiliary devices are created.
2. Mapping the BAR, which helps access doorbells since
its size is known after querying the firmware.
3. Retrieving the TCs and hardware CoS queue mappings.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20250701143511.280702-10-vikas.gupta@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Get the resources and capabilities from the firmware.
Add functions to manage the resources with the firmware.
These functions will help netdev reserve the resources
with the firmware before registering the device in future
patches. The resources and their information, such as
the maximum available and reserved, are part of the members
present in the bnge_hw_resc struct.
The bnge_reserve_rings() function also populates
the RSS table entries once the RX rings are reserved with
the firmware.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20250701143511.280702-8-vikas.gupta@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to communicate with the firmware.
Future patches will use these functions to send the
messages to the firmware.
Functions support allocating request/response buffers
to send a particular command. Each command has certain
timeout value to which the driver waits for response from
the firmware. In error case, commands may be either timed
out waiting on response from the firmware or may return
a specific error code.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20250701143511.280702-4-vikas.gupta@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I received a kernel-test-bot report[1] that shows the
[-Wunused-but-set-variable] warning. Since the previous commit I made, as
the 'Fixes' tag shows, gives users an option to turn on and off the
CONFIG_RFS_ACCEL, the issue then can be discovered and reproduced with
GCC specifically.
Like Simon and Jakub suggested, use fewer #ifdefs which leads to fewer
bugs.
[1]
All warnings (new ones prefixed by >>):
drivers/net/ethernet/broadcom/bnxt/bnxt.c: In function 'bnxt_request_irq':
>> drivers/net/ethernet/broadcom/bnxt/bnxt.c:10703:9: warning: variable 'j' set but not used [-Wunused-but-set-variable]
10703 | int i, j, rc = 0;
| ^
Fixes: 9b6a30febd ("net: allow rps/rfs related configs to be switched")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506282102.x1tXt0qz-lkp@intel.com/
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In both the read callback for struct cyclecounter, and in struct
timecounter, struct cyclecounter is declared as a const pointer.
Unfortunatly, a number of users of this pointer treat it as a non-const
pointer as it is burried in a larger structure that is heavily modified by
the callback function when accessed. This lie had been hidden by the fact
that container_of() "casts away" a const attribute of a pointer without any
compiler warning happening at all.
Fix this all up by removing the const attribute in the needed places so
that everyone can see that the structure really isn't const, but can,
and is, modified by the users of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/2025070124-backyard-hurt-783a@gregkh
The Rx rings are filled with Rx buffers. Which are supposed to fit
packet headers (or MTU if HW-GRO is disabled). The aggregation buffers
are filled with "device pages". Adjust the sizes of the page pool
recycling ring appropriately, based on ratio of the size of the
buffer on given ring vs system page size. Otherwise on a system
with 64kB pages we end up with >700MB of memory sitting in every
single page pool cache.
Correct the size calculation for the head_pool. Since the buffers
there are always small I'm pretty sure I meant to cap the size
at 1k, rather than make it the lowest possible size. With 64k pages
1k cache with a 1k ring is 64x larger than we need.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250626165441.4125047-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers that are using ops lock and don't depend on RTNL lock
still need to manage it because udp_tunnel's RTNL dependency.
Introduce new udp_tunnel_nic_lock and use it instead of
rtnl_lock. Drop non-UDP_TUNNEL_NIC_INFO_MAY_SLEEP mode from
udp_tunnel infra (udp_tunnel_nic_device_sync_work needs to
grab udp_tunnel_nic_lock mutex and might sleep).
Cover more places in v4:
- netlink
- udp_tunnel_notify_add_rx_port (ndo_open)
- triggers udp_tunnel_nic_device_sync_work
- udp_tunnel_notify_del_rx_port (ndo_stop)
- triggers udp_tunnel_nic_device_sync_work
- udp_tunnel_get_rx_info (__netdev_update_features)
- triggers NETDEV_UDP_TUNNEL_PUSH_INFO
- udp_tunnel_drop_rx_info (__netdev_update_features)
- triggers NETDEV_UDP_TUNNEL_DROP_INFO
- udp_tunnel_nic_reset_ntf (ndo_open)
- notifiers
- udp_tunnel_nic_netdevice_event, depending on the event:
- triggers NETDEV_UDP_TUNNEL_PUSH_INFO
- triggers NETDEV_UDP_TUNNEL_DROP_INFO
- ethnl_tunnel_info_reply_size
- udp_tunnel_nic_set_port_priv (two intel drivers)
Cc: Michael Chan <michael.chan@broadcom.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com>
Link: https://patch.msgid.link/20250616162117.287806-4-stfomichev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit under the Fixes tag below which updates the VNICs' RSS
and MRU during .ndo_queue_start(), needs to be extended to cover any
non-default RSS contexts which have their own VNICs. Without this
step, packets that are destined to a non-default RSS context may be
dropped after .ndo_queue_start().
We further optimize this scheme by updating the VNIC only if the
RX ring being restarted is in the RSS table of the VNIC. Updating
the VNIC (in particular setting the MRU to 0) will momentarily stop
all traffic to all rings in the RSS table. Any VNIC that has the
RX ring excluded from the RSS table can skip this step and avoid the
traffic disruption.
Note that this scheme is just an improvement. A VNIC with multiple
rings in the RSS table will still see traffic disruptions to all rings
in the RSS table when one of the rings is being restarted. We are
working on a FW scheme that will improve upon this further.
Fixes: 5ac066b7b0 ("bnxt_en: Fix queue start to update vnic RSS table")
Reported-by: David Wei <dw@davidwei.uk>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250613231841.377988-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before the commit under the Fixes tag below, bnxt_ulp_stop() and
bnxt_ulp_start() were always invoked in pairs. After that commit,
the new bnxt_ulp_restart() can be invoked after bnxt_ulp_stop()
has been called. This may result in the RoCE driver's aux driver
.suspend() method being invoked twice. The 2nd bnxt_re_suspend()
call will crash when it dereferences a NULL pointer:
(NULL ib_device): Handle device suspend call
BUG: kernel NULL pointer dereference, address: 0000000000000b78
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP PTI
CPU: 20 UID: 0 PID: 181 Comm: kworker/u96:5 Tainted: G S 6.15.0-rc1 #4 PREEMPT(voluntary)
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.4.3 01/17/2017
Workqueue: bnxt_pf_wq bnxt_sp_task [bnxt_en]
RIP: 0010:bnxt_re_suspend+0x45/0x1f0 [bnxt_re]
Code: 8b 05 a7 3c 5b f5 48 89 44 24 18 31 c0 49 8b 5c 24 08 4d 8b 2c 24 e8 ea 06 0a f4 48 c7 c6 04 60 52 c0 48 89 df e8 1b ce f9 ff <48> 8b 83 78 0b 00 00 48 8b 80 38 03 00 00 a8 40 0f 85 b5 00 00 00
RSP: 0018:ffffa2e84084fd88 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000001
RDX: 0000000000000000 RSI: ffffffffb4b6b934 RDI: 00000000ffffffff
RBP: ffffa1760954c9c0 R08: 0000000000000000 R09: c0000000ffffdfff
R10: 0000000000000001 R11: ffffa2e84084fb50 R12: ffffa176031ef070
R13: ffffa17609775000 R14: ffffa17603adc180 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffffa17daa397000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000b78 CR3: 00000004aaa30003 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
bnxt_ulp_stop+0x69/0x90 [bnxt_en]
bnxt_sp_task+0x678/0x920 [bnxt_en]
? __schedule+0x514/0xf50
process_scheduled_works+0x9d/0x400
worker_thread+0x11c/0x260
? __pfx_worker_thread+0x10/0x10
kthread+0xfe/0x1e0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2b/0x40
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
Check the BNXT_EN_FLAG_ULP_STOPPED flag and do not proceed if the flag
is already set. This will preserve the original symmetrical
bnxt_ulp_stop() and bnxt_ulp_start().
Also, inside bnxt_ulp_start(), clear the BNXT_EN_FLAG_ULP_STOPPED
flag after taking the mutex to avoid any race condition. And for
symmetry, only proceed in bnxt_ulp_start() if the
BNXT_EN_FLAG_ULP_STOPPED is set.
Fixes: 3c163f35bd ("bnxt_en: Optimize recovery path ULP locking in the driver")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Co-developed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250613231841.377988-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
