For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank in FPO / SubVP
/ DRR cases will not have any effect and we could hit underflow /
corruption.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
There is a corner case where the symclk otg flag is cleared
when disabling the phantom pipe for subvp (because the phantom
and main pipe share the same link). This is undesired because
we need the maintain the correct symclk otg flag state for
the main pipe.
For now only clear the flag only for HDMI signal type, since
it's only set for HDMI signal type (phantom is virtual). The
ideal solution is to not clear it if the stream is phantom but
currently there's a bug that doesn't allow us to do this. Once
this issue is fixed the proper fix can be implemented.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain cases, ODM pipe split can occur while stream already has test
pattern enabled. The new pipe used in the ODM combine config must be
configured to output the test pattern in this case.
[How]
If the stream is configured to output test pattern, then set the
test_pattern_changed update flag for the new pipe when it gets enabled.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream so
there is no need to have two flags to control it. Unifying this to a
single flag allows dc_stream_adjust_vmin_vmax to skip actual
programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When we're in a no plane config, DCN is always asserting
P-State allow
- This creates a scenario where the P-State blackout can start
just as VUPDATE takes place and transitions the DCN config to
a one where one or more HUBP's are active which can result in
underflow
- To fix this issue, force p-state disallow and unforce after
the transition from no planes case -> one or more planes active
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current DPG test pattern logic does not account for ODM configuration
changes after test pattern has already been programmed. For example, if
ODM2:1 is enabled after test pattern is already being output, the second
pipe is not programmed to output test pattern, causing half the screen
to be black.
[How]
Move DPG test pattern parameter calculations into separate function.
Whenever ODM pipe configuration changes, re-calculate DPG test pattern
parameters and program DPG if test pattern is currently enabled.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
