Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
- Improve display debug msgs and other general clean-ups (Ville, Rahuul)
- PSR fixes and improvements around selective fetch (Jouni, Ville)
- Remove FBC restrictions for Xe2LPD displays (Vinod)
- Skip some timing checks on BXT/GLK DSI transcoders (Ville)
- DP MST Fixes (Ville)
- Correct the input parameter on _intel_dsb_commit (heminhong)
- Fix IP version of the display WAs (Bala)
- DGFX uses direct VBT pin mapping (Clint)
- Proper handling of bool on PIPE_CONF_CHECK macros (Jani)
- Skip state verification with TBT-ALT mod (Mika Kahona)
- General organization of display code for reusage with Xe
(Jouni, Luca, Jani, Maarten)
- Squelch a sparse warning (Jani)
- Don't use "proxy" headers (Andy Shevchenko)
- Use devm_gpiod_get() for all GPIOs (Hans)
- Fix ADL+ tiled plane stride (Ville)
- Use octal permissions in display debugfs (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZXIWG6bRYaUw0w6-@intel.com
At the moment modesetting pipe C on IVB will fail if pipe B uses 4 FDI
lanes. Make the BW sharing more dynamic by trying to reduce pipe B's
link bpp in this case, until pipe B uses only up to 2 FDI lanes.
For this instead of the encoder compute config retry loop - which
reduced link bpp only for the encoder's pipe - reduce the maximum link
bpp for pipe B/C as required after all CRTC states are computed and
recompute the CRTC states with the new bpp limit.
Atm, all FDI encoder's compute config function returns an error if a BW
constrain prevents increasing the pipe bpp value. The corresponding
crtc_state->bw_constrained check can be replaced with checking
crtc_state->max_link_bpp_x16, add TODO comments for this. SDVO is an
exception where this case is only handled in the outer config retry
loop, failing the modeset with a WARN, add a FIXME comment to handle
this in the encoder code similarly to other encoders.
v2:
- Don't assume that a CRTC is already in the atomic state, while
reducing its link bpp.
- Add DocBook description to intel_fdi_atomic_check_link().
v3:
- Enable BW management for FDI links in a separate patch. (Ville)
v4: (Ville)
- Fail the SDVO encoder config computation if it doesn't support the
link bpp limit.
- Add TODO: comments about checking link_bpp_x16 instead of
bw_constrained.
v5:
- Replace link bpp limit check with a FIXME: comment in
intel_sdvo_compute_config(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Amended commit message wrt. changes in v5]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921195159.2646027-11-imre.deak@intel.com
Each SDVO device can have up to three sets of DDC pins.
Currently we just register a single i2c_adapter for the
entire SDVO device and semi-randomly pick the "correct"
set of DDC pins during intel_sdvo_tmds_sink_detect().
This doesn't make any real sense especially if we have
multiple outputs each with their own dedicated DDC bus.
Let's clean up this mess and register a dedicated
i2c_adapter for each of the possible pin pairs. Each
output (ie. connector) can then pick the correct i2c_adapter
to use for its DDC bus. And we can just switch over to
drm_connector_init_with_ddc() to take care of the
connector->ddc association, which also populates the
"ddc" sysfs symlink as a bonus.
And now that things are based on the actual connector we can
also nuke the sketchy sdvo->controller_output thing.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825134431.24391-6-ville.syrjala@linux.intel.com
The SDVO code already warns when the port in question doesn't
actually support SDVO. Let's make that also bail the encoder
registration like the generic assert_port_valid() we added.
And add a similar thing for g4x HDMI, mainly because on g4x
itsefl port D only supports DP but not SDVO/HDMI. For the
other platforms the generic port_mask check should actually
be sufficient, but since we're here might as well list the
ports.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-6-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
