Starting with commit 17ce8a6907 ("drm/amd/display: Add dsc pre-validation in
atomic check"), amdgpu resets the CRTC state mode_changed flag to false when
recomputing the DSC configuration results in no timing change for a particular
stream.
However, this is incorrect in scenarios where a change in MST/DSC configuration
happens in the same KMS commit as another (unrelated) mode change. For example,
the integrated panel of a laptop may be configured differently (e.g., HDR
enabled/disabled) depending on whether external screens are attached. In this
case, plugging in external DP-MST screens may result in the mode_changed flag
being dropped incorrectly for the integrated panel if its DSC configuration
did not change during precomputation in pre_validate_dsc().
At this point, however, dm_update_crtc_state() has already created new streams
for CRTCs with DSC-independent mode changes. In turn,
amdgpu_dm_commit_streams() will never release the old stream, resulting in a
memory leak. amdgpu_dm_atomic_commit_tail() will never acquire a reference to
the new stream either, which manifests as a use-after-free when the stream gets
disabled later on:
BUG: KASAN: use-after-free in dc_stream_release+0x25/0x90 [amdgpu]
Write of size 4 at addr ffff88813d836524 by task kworker/9:9/29977
Workqueue: events drm_mode_rmfb_work_fn
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0xa0
print_address_description.constprop.0+0x88/0x320
? dc_stream_release+0x25/0x90 [amdgpu]
print_report+0xfc/0x1ff
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x225/0x4e0
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_report+0xe1/0x180
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_check_range+0x125/0x200
dc_stream_release+0x25/0x90 [amdgpu]
dc_state_destruct+0x14d/0x5c0 [amdgpu]
dc_state_release.part.0+0x4e/0x130 [amdgpu]
dm_atomic_destroy_state+0x3f/0x70 [amdgpu]
drm_atomic_state_default_clear+0x8ee/0xf30
? drm_mode_object_put.part.0+0xb1/0x130
__drm_atomic_state_free+0x15c/0x2d0
atomic_remove_fb+0x67e/0x980
Since there is no reliable way of figuring out whether a CRTC has unrelated
mode changes pending at the time of DSC validation, remember the value of the
mode_changed flag from before the point where a CRTC was marked as potentially
affected by a change in DSC configuration. Reset the mode_changed flag to this
earlier value instead in pre_validate_dsc().
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/5004
Fixes: 17ce8a6907 ("drm/amd/display: Add dsc pre-validation in atomic check")
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit cc7c7121ae)
[Why]
The AMD VSDB contains two bits that indicate the type of panel connected.
This can be useful for policy decisions based upon panel technology.
[How]
Read the bits for the panel type when parsing VSDB and store them in
the dc_link.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Right now, the HDMI HPD filter is enabled by default at 1500ms.
We want to disable it by default, as most modern displays with HDMI do
not require it for DPMS mode.
The HPD can instead be enabled as a driver parameter with a custom delay
value in ms (up to 5000ms).
Fixes: c918e75e1e ("drm/amd/display: Add an HPD filter for HDMI")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4859
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IGT CRC tests fail on replay panels due to invalid CRC values
captured when replay is active.
[How]
- Disable replay when CRC source is enabled; set flag to
prevent unexpected re-enable
- Reset flag when CRC source is disabled to allow replay
Reviewed-by: ChiaHsuan (Tom) Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Newer ASICs have different PSP footer sizes which lead to driver
failing to locate the DMCUB FW meta info, which in turn causes
improper DMCUB FW loading and causes DMCUB to crash.
Add support for custom PSP footer sizes and check 512B by default
as well.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some monitors perform rapid “autoscan” HPD re‑assertions right after a
disconnect or powersaving mode enablement. These appear as a quick
disconnect→reconnect with an identical EDID. Since Linux has no HDMI
hotplug detection (HPD) filter, these quick reconnects are seen as hotplug
events, which can unintentionally wake a system with DPMS off.
An example: https://gitlab.freedesktop.org/drm/amd/-/issues/2876
Such 'fake reconnects' are considered when the interval between a
disconnect and a connect is within 1500ms (experimentally chosen using
several monitors), and the two connections have the same EDID.
[How]
Implement a time-based debounce mechanism:
1. On HDMI disconnect detection, instead of immediately processing the
HPD event, save the current sink and schedule delayed work (default 1500ms)
2. If another HDMI disconnect HPD event arrives during the debounce period,
it reschedules the pending work, ensuring only the final state is processed.
3. When the debounce timer expires, re-detect the display and compare the
new sink with the cached one using EDID comparison.
4. If sinks match (same EDID), this was a spontaneous HPD toggle:
- Update connector state internally
- Skip hotplug event to prevent desktop rearrangement
If sinks differ, this was a real display change:
- Process normally with the hotplug event
The debounce delay is configurable via module parameter
'hdmi_hpd_debounce_delay_ms'.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2876
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 0887054d14 ("drm/amd: Drop abm_level property") dropped the
abm level property in favor of sysfs control. Since then there have
been discussions that compositors showed an interest in modifying
a vendor specific property instead.
So re-introduce the abm level property, but with different semantics.
Rather than being an integer it's now an enum. One of the enum options
is 'sysfs', and that is because there is still a sysfs file for use by
userspace when the compositor doesn't support this property.
If usespace has not modified this property, the default value will
be for sysfs to control it. Once userspace has set the property stop
allowing sysfs control.
The property is only attached to non-OLED eDP panels.
Cc: Xaver Hugl <xaver.hugl@kde.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't update DC stream color components during atomic check. The driver
will continue validating the new CRTC color state but will not change DC
stream color components. The DC stream color state will only be
programmed at commit time in the `atomic_setup_commit` stage.
It fixes gamma LUT loss reported by KDE users when changing brightness
quickly or changing Display settings (such as overscan) with nightlight
on and HDR. As KWin can do a test commit with color settings different
from those that should be applied in a non-test-only commit, if the
driver changes DC stream color state in atomic check, this state can be
eventually HW programmed in commit tail, instead of the respective state
set by the non-blocking commit.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4444
Reported-by: Xaver Hugl <xaver.hugl@gmail.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On clients that utilize AMD_PRIVATE_COLOR properties for HDR support,
brightness sliders can include a hardware controlled portion and a
gamma-based portion. This is the case on the Steam Deck OLED when using
gamescope with Steam as a client.
When a user sets a brightness level while HDR is active, the gamma-based
portion and/or hardware portion are adjusted to achieve the desired
brightness. However, when a modeset takes place while the gamma-based
portion is in-use, restoring the hardware brightness level overrides the
user's overall brightness level and results in a mismatch between what
the slider reports and the display's current brightness.
To avoid overriding gamma-based brightness, only restore HW backlight
level after boot or resume. This ensures that the backlight level is
set correctly after the DC layer resets it while avoiding interference
with subsequent modesets.
Fixes: 7875afafba ("drm/amd/display: Fix brightness level not retained over reboot")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4551
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP validation may fail with multiple displays and higher color depths.
The sink may support others though.
[How]
When DP bandwidth validation fails, progressively fallback through:
- YUV422 8bpc (bandwidth efficient)
- YUV422 6bpc (reduced color depth)
- YUV420 (last resort)
This resolves cases where displays would show no image due to insufficient
DP link bandwidth for the requested RGB mode.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-next for v6.18:
Cross-subsystem Changes:
- Update a number of DT bindings for STM32MP25 Arm SoC
Core Changes:
gem:
- Simplify locking for GPUVM
panel-backlight-quirks:
- Add additional quirks for EDID, DMI, brightness
sched:
- Fix race condition in trace code
- Clean up
sysfb:
- Clean up
Driver Changes:
amdgpu:
- Give kernel jobs a unique id for better tracing
amdxdna:
- Improve error reporting
bridge:
- Improve ref counting on bridge management
- adv7511: Provide SPD and HDMI infoframes
- it6505: Replace crypto_shash with sha()
- synopsys: Add support for DW DPTX Controller plus DT bindings
gud:
- Replace simple-KMS pipe with regular atomic helpers
imagination:
- Improve power management
- Add support for TH1520 GPU
- Support Risc-V architectures
ivpu:
- Clean up
nouveau:
- Improve error reporting
panthor:
- Fail VM bind if BO has offset
- Clean up
rcar-du:
- Make number of lanes configurable
rockchip:
- Add support for RK3588 DPTX output
rocket:
- Use kfree() and sizeof() correctly
- Test DMA status
- Clean up
sitronix:
- st7571-i2c: Add support for inverted displays and 2-bit grayscale
- Clean up
stm:
- ltdc: Add support support for STM32MP257F-EV1 plus DT bindings
tidss:
- Convert to kernel's FIELD_ macros
v3d:
- Improve job management and locking
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250904090932.GA193997@linux.fritz.box
Certain OLED devices malfunction on specific brightness levels.
Specifically, when DP_SOURCE_BACKLIGHT_LEVEL is written to with
the first byte being 0x00 and sometimes 0x01, the panel forcibly
turns off until the device sleeps again.
Below are some examples. This was found by iterating over brighness
ranges while printing DP_SOURCE_BACKLIGHT_LEVEL. It was found that
the screen would malfunction on specific values, and some of them
were collected.
Therefore, introduce a quirk where the minor byte of brightness is
OR'd with 0x03 to avoid the range of invalid values.
This quirk was tested by removing the workarounds and iterating
from 0 to 50_000 value ranges with a cadence of 0.2s/it. The
range of the panel is 1000...400_000, so the values were slightly
interpolated during testing. The custom brightness curve added on
6.15 was disabled.
86016: 10101000000000000
86272: 10101000100000000
87808: 10101011100000000
251648: 111101011100000000
251649: 111101011100000001
86144: 10101000010000000
87809: 10101011100000001
251650: 111101011100000010
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3803
Tested-by: Philip Müller <philm@manjaro.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250829145541.512671-5-lkml@antheas.dev
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
[why]
Read link setting inside mode validation is not always the final downlink setting.
It is found true in Synaptics branch device.
At bootup, the preferred mode being set right after 1080p is set. It occurred
before graphic load. That modeset switch in a short period of time makes
the branch device switch back and forth from lower and higher link rate,
observed at Synaptics branch device.
DP2 RTK hub on the other hand, sticks to highest available downlink rate after bootup.
Existing check of runtime downlink setting in mode validation shows asynchronous at
branch device link switch, i.e., downlink switch to higher link rate not yet complete
when the mode validation tries to probe the downlink setting. That makes mode validation
checking downlink setting making wrong decision by pruning modes that should pass the
validation after the downlink setting switch is complete.
[how]
If Synaptics is found at the last branch, skip checking downlink setting
at mode validation.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following warning in struct documentation:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:168: warning: expecting prototype for struct dm_vupdate_work. Prototype was for struct vupdate_offload_work instead
Fixes: c210b757b4 ("drm/amd/display: fix dmub access race condition")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Accessing DC from amdgpu_dm is usually preceded by acquisition of
dc_lock mutex. Most of the DC API that DM calls are under a DC lock.
However, there are a few that are not. Some DC API called from interrupt
context end up sending DMUB commands via a DC API, while other threads were
using DMUB. This was apparent from a race between calls for setting idle
optimization enable/disable and the DC API to set vmin/vmax.
Offload the call to dc_stream_adjust_vmin_vmax() to a thread instead
of directly calling them from the interrupt handler such that it waits
for dc_lock.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dml2_soc_bb struct can continuously receive updates for future ASICs.
Alignment issues may arise since VBIOS DMCUB contains an older version of
the SOC BB.
Populating the bounding box with values from DMCUB is no longer necessary
since values such as UCLK will be overridden by values acquired by PMFW
anyways.
[HOW]
Use bb_from_dmub to store DCN specific bounding box parameters in DMCUB.
Add helpers to translate DCN specific struct to the corresponding
dml2_soc_bb field.
To avoid alignment issues:
Deprecate applying DMCUB SoC BB for DCN4
For future projects:
Create a flattened struct containing all sensitive parameters in the
bounding box. New parameters can be added to the bottom of the new struct
as needed.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMI quirks are relatively big code that makes amdgpu_dm 200 lines
larger.
[How]
Move DMI quirks into a dedicated source file and make all quirks
variables for `struct amdgpu_display_manager`.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
htmldocs build warning: "Function parameter or struct member 'fused_io'
not described in 'amdgpu_display_manager'".
[How]
Add missing description.
Fixes: ce801e5d6c ("drm/amd/display: HDCP Locality check using DMUB Fused IO")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP locality check has strict timing requirements, currently broken
due to reliance on msleep which does not guarantee accuracy.
The PR moves the write-poll-read sequence into DMUB using new generic
Fused IO interface, where the timing accuracy is greatly improved.
New flow is enabled using DCN resource capability bit (none for now),
or using a debug flag.
[How]
* Extended mod_hdcp_config with new function for requesting DMUB
to execute a sequence of fused I2C/AUX commands and synchronously
wait until an outbox reply arrives or a timeout expires.
* If the timeout expires, send an abort to DMUB.
* Update HDCP to use the DMUB for locality check if supported.
* Add DC_HDCP_LC_FORCE_FW_ENABLE and DC_HDCP_LC_ENABLE_SW_FALLBACK.
* Make the first enable new flow regardless of resource capabilities.
* Make the second enable fallback to old SW flow.
* Clean up makefile source file listings for easier updates.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't try to operate on a drm_wb_connector as an amdgpu_dm_connector.
While dereferencing aconnector->base will "work" it's wrong and
might lead to unknown bad things. Just... don't.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose the OEM i2c bus on boards that support it.
This bus is used for OEM specific features like RGB, etc.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Observed frame rate get dropped by tool like glxgear. Even though the
output to monitor is 60Hz, the rendered frame rate drops to 30Hz lower.
It's due to code path in some cases will trigger
dm_dp_mst_is_port_support_mode() to read out remote Link status to
assess the available bandwidth for dsc maniplation. Overhead of keep
reading remote DPCD is considerable.
[How]
Store the remote link BW in mst_local_bw and use end-to-end full_pbn
as an indicator to decide whether update the remote link bw or not.
Whenever we need the info to assess the BW, visit the stored one first.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3720
Fixes: fa57924c76 ("drm/amd/display: Refactor function dm_dp_mst_is_port_support_mode()")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds the cec_notifier feature to amdgpu driver.
The changes will allow amdgpu driver code to notify EDID
and HPD changes to an eventual CEC adapter.
Signed-off-by: Kun Liu <Kun.Liu2@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Variables relates to secure display are spreading out within struct
amdgpu_display_manager.
[How]
Encapsulate relevant variables into struct secure_display_context and
adjust relevant affected codes.
Reviewed-by: HaoPing Liu <haoping.liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Under mst scenario, mst streams are from the same link_enc_hw_inst.
As the result, can't utilize that as the phy index for distinguising
different stream sinks.
[How]
Sort the connectors by:
link_enc_hw_instance->mst tree depth->mst RAD
After sorting the phy index assignment, store connector's relevant info
into dm mapping array. Once need the index, just look up the static
array.
Reviewed-by: HaoPing Liu <haoping.liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HPD sense notification has been implemented in DMUB, which
can occur during low power states and need to be
notified from firmware to driver.
[HOW]
Define callback and register new HPD sense notification.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the `power_saving_policy` property is set to bit mask
"Require color accuracy" ABM should be disabled immediately and
any requests by sysfs to update will return an -EBUSY error.
When the `power_saving_policy` property is set to bit mask
"Require low latency" PSR should be disabled.
When the property is restored to an empty bit mask ABM and PSR
can be enabled again.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703051722.328-3-mario.limonciello@amd.com
[Why]
DCN is the display hardware for amdgpu. DRM planes are backed by DCN
hardware pipes, which carry pixel data from one end (memory), to the
other (output encoder).
Each DCN pipe has the ability to blend in a cursor early on in the
pipeline. In other words, there are no dedicated cursor planes in DCN,
which makes cursor behavior somewhat unintuitive for compositors.
For example, if the cursor is in RGB format, but the top-most DRM plane
is in YUV format, DCN will not be able to blend them. Because of this,
amdgpu_dm rejects all configurations where a cursor needs to be enabled
on top of a YUV formatted plane.
From a compositor's perspective, when computing an allocation for
hardware plane offloading, this cursor-on-yuv configuration result in an
atomic test failure. Since the failure reason is not obvious at all,
compositors will likely fall back to full rendering, which is not ideal.
Instead, amdgpu_dm can try to accommodate the cursor-on-yuv
configuration by opportunistically reserving a separate DCN pipe just
for the cursor. We can refer to this as "overlay cursor mode". It is
contrasted with "native cursor mode", where the native DCN per-pipe
cursor is used.
[How]
On each crtc, compute whether the cursor plane should be enabled in
overlay mode. If it is, mark the CRTC as requesting overlay cursor mode.
Overlay cursor should be enabled whenever there exists a underlying
plane that has YUV format, or is scaled differently than the cursor. It
should also be enabled if there is no underlying plane, or if underlying
planes do not cover the entire CRTC.
During DC validation, attempt to enable a separate DCN pipe for the
cursor if it's in overlay mode. If that fails, or if no overlay mode is
requested, then fallback to native mode.
v2:
* Update commit message for when overlay cursor should be enabled
* Also consider scale and no-underlying-plane case (cursor on crtc bg)
* Consider all underlying planes when determinig overlay/native, not
just the plane immediately beneath the cursor, as it may not cover the
entire CRTC.
* Fix typo s/decending/descending/
* Force native cursor on pre-DCN hardware
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
It actually exposes '6' types in enum dmub_notification_type. Not 5. Using smaller
number to create array dmub_callback & dmub_thread_offload has potential to access
item out of array bound. Fix it.
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, amdgpu will always set up the brightness at 100% when it
loads. However this is jarring when the BIOS has it previously
programmed to a much lower value.
The ACPI ATIF method includes two members for "ac_level" and "dc_level".
These represent the default values that should be used if the system is
brought up in AC and DC respectively.
Use these values to set up the default brightness when the backlight
device is registered.
v2: squash in ACPI fix
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allocate some memory, send the address in chunks to dmub, and finally
ask it to copy the bounding box data into the newly allocated memory.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
