[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending
[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dc sw clock implementation of navi10 and raven are not exact the
same. dcccg, dchub reference clock initialization is done after dc calls
vbios dispcontroller_init table. for raven family, before
dispcontroller_init is called by dc, the ref clk values are referred
by sw clock implementation and program asic register using wrong
values. this causes dchub pstate error. This need provide valid ref
clk values. for navi10, since dispcontroller_init is not called,
dchubbub_global_timer_enable = 0, hubbub2_get_dchub_ref_freq will
hit aeert. this need remove hubbub2_get_dchub_ref_freq from this
location and move to dcn20_init_hw.
[HOW] for all asic, initialize dccg, dchub ref clk with data from
vbios firmware table by default. for raven asic family, use these data
from vbios, for asic which support sw dccg component, like navi10,
read ref clk by sw dccg functions and update the ref clk.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this header, we get a compiler error in some configurations:
.../dc/dcn20/dcn20_hwseq.c: In function 'dcn20_hwss_wait_for_blank_complete':
.../dc/dcn20/dcn20_hwseq.c:1493:3: error: implicit declaration of function 'udelay' [-Werror=implicit-function-declaration]
Note: the use of udelay itself may be problematic, as can occupy
the CPU for 200ms in a busy-loop here.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. With the introduction
of new asics we are required to coordinate vmid use with external
components.
This change converts vmid logic to a DAL module allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
VM implemenation is missing conversion from HW values in hubbub
DM not passing actual PTB during flip
[how]
add proper HW conversion from logical values
fix cases where we programmed VA even though we are in PA
plumb in PTB from DM
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently DSC power gating is disabled by default because the power
transition doesn't happen, causing a crash on some systems
[how]
Fix the lack of power state transition and enable DSC power gating
by default.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want a test pattern to show up on screen when we're blanked and have
visual confirm enabled, for debugging. Raven does this, it's a mistake that
Navi does not.
[How]
- in "blank_pixel_data", set appropriate DPG pattern for visual confirm
- refactor DPG calls out of "enable_stream_timing"
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Plane disable gets calls when we enable blank. On DCN2, we blank by using
DPG to display a black colour instead of using OTG blank. DPG runs off the
OPP clock, therefore we shouldn't disable the OPP clock when disabling the
plane. We do need to disable the OPP clock when disabling the entire pipe,
that will be addressed in a separate commit.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GSL is being used to synchronize pipes when vsync is off but
on transition to vsync on during a mode change GSL is not
being reset correctly.
[How]
Disable GSL on any plane that is disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to ensure that incoming flips are latched and
complete immediately, we need to program the vupdate
interrupt to come during the back porch of each frame.
[How]
Program the vupdate start_line to be in the back porch
like it's done for DCN1.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1 and DCN2.
In addition, future HW will need to access the HUBPREQ_DEBUG and
CUR_TTU_CNTL0 register for hubp_init. Add that here.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OPTC data format was left at its default value (444) when enabling
ODM combine. This caused issues with FPGA capture.
[How]
Write the OPTC_DATA_FORMAT field when enabling ODM combine.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when an update programming sequence requires both
front end and back end pipe to be updated synchronously,
a global update lock needs to be set to ensure that
we don't get a frame with only front end update but
not the back end update.
[how]
setup global lock parameters on enable_stream_timing.
enable global lock when pipe_control_lock_global is called.
disable global lock when pipe_control_lock is called.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can split validation into three parts: getting voltage level, getting
watermarks, and rq/dlg calculations. The voltage level is enough to answer
the question "do we support this state", and the rest of it is to determine
what hardware programming is needed to support the state. Most of the calls
to validate_bandwidth only care about the first part, so we added an early
return in that case
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.
[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn20_apply_ctx_for_surface can be called with 0 planes, which means we
should blank the display. In this case when we get down to
dcn20_setup_gsl_group_as_lock, pipe_ctx->plane_state is NULL, but we don't
check for it. However, this function is only called by
dcn20_pipe_control_lock, and in that function we alraedy have a local for
the immediate flip status, which is what we care about in the plane state.
[How]
- pass in immediate flip status as parameter
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn*_disable_plane() doesn't unlock the pipe anymore, making the extra
lock unnecessary.
In addition - during full plane updates - all necessary pipes should be
locked/unlocked together when modifying hubp to avoid tearing in
pipesplit setups.
[How]
Remove redundant locks, and add function to lock all pipes. If an
interdependent pipe update is required, lock down all pipes. Otherwise,
lock only the top pipe for the updated pipe tree.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous fix was done for DCN1 that needed to be ported to DCN2:
commit 60c677534e73 ("drm/amd/display: Disconnect mpcc when changing tg")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
