Since IMX serial SOCs support low bus freq mode, some clocks freq
may change to save power. I2C needs to check the clock source and
update the divider.
For example:
i.MX6SL I2C clk is from IPG_PERCLK which is sourced from IPG_CLK.
Under normal operation, IPG_CLK is 66MHz, ipg_perclk is at 22MHz.
In low bus freq mode, IPG_CLK is at 12MHz and IPG_PERCLK is down
to 4MHz. So the I2C driver must update the divider register for
each transaction when the current IPG_PERCLK is not equal to the
clock of previous transaction.
Signed-off-by: Fugang Duan <B38611@freescale.com>
[wsa: removed an outdated comment and simplified debug output]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Test i2c device Maxim max44009, datasheet is located at:
http://www.maximintegrated.com/datasheet/index.mvp/id/7175
The max44009 support repeat operation like:
read -> repeat restart -> read/write
The current i2c imx host controller driver don't support this
operation that causes i2c bus hang due to "MTX" is cleared in
.i2c_imx_read(). If "read" is the last message there have no problem,
so the current driver supports all SMbus operation like:
write -> repeat restart -> read/write
IMX i2c controller for master receiver has some limitation:
- If it is the last byte for one operation, it must generate STOP
signal before read I2DR to prevent controller from generating another
clock cycle.
- If it is the last byte in the read, and then do repeat restart, it must
set "MTX" before read I2DR to prevent controller from generating another
extra clock cycle.
The patch is to fix the issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should always check if the bus is free, independently if it is a read
or write. It should be done before the first message, though. After
that, we ourselves keep the bus busy. Remove a 'ret' assignment which
only silenced a build warning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead. Actually, this is even more readable since the old
function used a mix of "=" and "|=".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Kaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull iommu fixes from Joerg Roedel:
"Three fixes for the AMD IOMMU driver:
- fix a locking issue around get_user_pages()
- fix two issues with device aliasing and exclusion range handling"
* tag 'iommu-fixes-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: fix enabling exclusion range for an exact device
iommu/amd: Take mmap_sem when calling get_user_pages
iommu/amd: Fix interrupt remapping for aliased devices
Pull iscsi_ibft fix from Konrad Rzeszutek Wilk:
"Fix iBFT regression on Broadcom NICs introduced in 3.2"
* tag 'stable/for-linus-3.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
iscsi_ibft: Fix finding Broadcom specific ibft sign
Pull SH driver fix from Simon Horman:
"Compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI
This resolves a regression introduced in v3.14 by commit bf98c1eac1
("ARM: Rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY")"
* tag 'renesas-sh-drivers-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI
Pull media fixes from Mauro Carvalho Chehab:
"Most of the changes are drivers fixes (rtl28xuu, fc2580, ov7670,
davinci, gspca, s5p-fimc and s5c73m3).
There is also a compat32 fix and one infoleak fixup at the media
controller"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] V4L2: fix VIDIOC_CREATE_BUFS in 64- / 32-bit compatibility mode
[media] V4L2: ov7670: fix a wrong index, potentially Oopsing the kernel from user-space
[media] media-device: fix infoleak in ioctl media_enum_entities()
[media] fc2580: fix tuning failure on 32-bit arch
[media] Prefer gspca_sonixb over sn9c102 for all devices
[media] media: davinci: vpfe: make sure all the buffers unmapped and released
[media] staging: media: davinci: vpfe: make sure all the buffers are released
[media] media: davinci: vpbe_display: fix releasing of active buffers
[media] media: davinci: vpif_display: fix releasing of active buffers
[media] media: davinci: vpif_capture: fix releasing of active buffers
[media] s5p-fimc: Fix YUV422P depth
[media] s5c73m3: Add missing rename of v4l2_of_get_next_endpoint() function
[media] rtl28xxu: silence error log about disabled rtl2832_sdr module
[media] rtl28xxu: do not hard depend on staging SDR module
Pull staging driver fixes from Greg KH:
"Here are five staging driver fixes for 3.15-rc6 that resolve some
reported issues. They are for the imx and rtl8723au drivers"
* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723au: Do not reset wdev->iftype in netdev_close()
staging: rtl8723au: Use correct pipe type for USB interrupts
imx-drm: imx-tve: correct DDC property name to 'ddc-i2c-bus'
imx-drm: imx-drm-core: skip components whose parent device is disabled
imx-drm: imx-drm-core: fix imx_drm_encoder_get_mux_id
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an SHPCHP hotplug regression, a "wait for pending
transaction" problem (used in device reset paths), and an email
address update.
PCI device hotplug:
- Fix SHPCHP bus speed mismatch issue (Marcel Apfelbaum)
Miscellaneous:
- Fix pci_wait_for_pending_transaction() (Gavin Shan)
- Update email address (Ben Hutchings)"
* tag 'pci-v3.15-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Wrong register used to check pending traffic
PCI: shpchp: Check bridge's secondary (not primary) bus speed
PCI: Update my email address
Pull /dev/random fix from Ted Ts'o:
"This fixes a BUG_ON-causing regression that was introduced during the
last merge window"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix BUG_ON caused by accounting simplification
Pull clock framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
As usual most fixes are for platform-specific clock drivers, but there
are also two fixes to the clk core after recent changes to the way
that clock unregistration is handled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: tegra: Fix wrong value written to PLLE_AUX
clk: shmobile: clk-mstp: change to using clock-indices
clk: Fix slab corruption in clk_unregister()
clk: Fix double free due to devm_clk_register()
clk: socfpga: fix clock driver for 3.15
clk: divider: Fix best div calculation for power-of-two and table dividers
clk: bcm281xx: don't use unnamed structs or unions
Pull spi fixes from Mark Brown:
"A few core fixes around outlying cases here, nothing that should
affect most users but useful fixes. The diffstat is rather larger
than one might hope due some simple code motion in the fix for
!CONFIG_DMA, the actual meaningful change is much smaller.
- Fix handling of unsupported dual and quad mode support on slave
registration so that drivers that can degrade gracefully do so,
preventing regressions for drivers this is added.
- Fix build in !CONFIG_DMA cases following addition of generic DMA
mapping support.
- Fix error handling for queue creation which due to wider kernel
changes can be triggered more easily.
- A couple of driver specific fixes"
* tag 'spi-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: Prevent DMA from transferring too many bytes
spi: core: Don't destroy master queue if we fail to create it
spi: qup: Fix return value checking for pm_runtime_get_sync()
spi: core: Protect DMA code by #ifdef CONFIG_HAS_DMA
spi: core: Ignore unsupported Dual/Quad Transfer Mode bits
Pull GPIO fixes from Linus Walleij:
- fix a null pointer bug in the ICH6 chipset driver
- fix device tree registration for the mcp23s08 driver
* tag 'gpio-v3.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mcp23s08: Bug fix of SPI device tree registration.
gpio: ich: set regs and reglen for i3100 and ich6 chipset
Pull libata fixes from Tejun Heo:
"Mostly device-specific fixes. The only thing which isn't is the fix
for zpodd oops-on-detach bug"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: imx: PLL clock needs 100us to settle down
ata: pata_at91 only works on sam9
libata: clean up ZPODD when a port is detached
ahci: imx: software workaround for phy reset issue in resume
ahci: imx: add namespace for register enums
ahci: disable DEVSLP for Intel Valleyview
Pull crypto fixes from Herbert Xu:
"This fixes a NULL pointer dereference on allocation failure in caam,
as well as a regression in the ctr mode on s390 that was added with
the recent concurrency fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390 - fix aes,des ctr mode concurrency finding.
crypto: caam - add allocation failure handling in SPRINTFCAT macro
Pull scsi target fixes from Nicholas Bellinger:
"This series include:
- Close race between iser-target network portal shutdown + accepting
new connection logins (sagi)
- Fix free-after-use regression in tcm_fc post conversion to
percpu-ida pre-allocation (nab)
- Explicitly disable Immediate + Unsolicited Data for iser-target
connections when T10-PI is enabled (sagi + nab)
- Allow pi_prot_type + emulate_write_cache attributes to be set to
zero regardless of backend support (andy)
- memory leak fix (mikulas)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: fix memory leak on XCOPY
target: Don't allow setting WC emulation if device doesn't support
iscsi-target: Disable Immediate + Unsolicited Data with ISER Protection
tcm_fc: Fix free-after-use regression in ft_free_cmd
iscsi-target: Change BUG_ON to REJECT in iscsit_process_nop_out
Target/iscsi,iser: Avoid accepting transport connections during stop stage
Target/iser: Fix iscsit_accept_np and rdma_cm racy flow
Target/iser: Fix wrong connection requests list addition
target: Allow non-supporting backends to set pi_prot_type to 0
Pull ACPI and power management fixes from Rafael Wysocki:
"Still fixing regressions (partly by reverting commits that broke
things for people), fixing other stable-candidate bugs and adding some
blacklist entries for ACPI video and _OSI.
Two ACPICA regression fixes (one recent and one for a 3.14 commit), a
fix for an ACPI-related regression in TPM (introduced in 3.14), a
revert of the ACPI AC driver conversion in 3.13 that went wrong for an
unknown reason, two reverts of commits that attempted to remove an old
user space interface in /proc and broke some utilities, in 3.13 too, a
fix for a CPU hotplug bug in the ACPI processor driver (stable
material), two (stable candidate) fixes for intel_pstate and a few new
blacklist entries, mostly for systems that shipped with Windows 8.
Specifics:
- ACPICA fix for a stale pointer access introduced by a recent commit
in the XSDT validation code from Lv Zheng.
- ACPICA fix for the default value of the command line switch to
favor 32-bit FADT addresses (in case there's a conflict between a
64-bit and a 32-bit address). The previous default was that the
32-bit version would take precedence and we tried to change it to
the other way around and it didn't work. From Lv Zheng.
- A TPM commit related to ACPI _DSM in 3.14 caused the driver to
refuse to load if a specific _DSM was missing and that broke resume
from system suspend on Chromebooks that require the TPM hardware to
be restored to a working state during resume by the OS. Restore
the old behavior to load the driver if the _DSM in question is not
present, but prevent it from using the feature the _DSM is for.
- ACPI AC driver conversion in 3.13 broke thermal management on at
least one machine and has to be reverted. From Guenter Roeck.
- Two reverts of 3.13 commits that attempted to remove the old ACPI
battery interface in /proc, but turned out to break some utilities
still using that interface. From Lan Tianyu.
- ACPI processor driver fix to prevent acpi_processor_add() from
modifying the CPU device's .offline field which leads to breakage
if the initial online of the CPU fails. From Igor Mammedov.
- Two intel_pstate fixes, one to take a BayTrail documentation update
into account and one to avoid forcing the maximum P-state on init
which causes CPU PM trouble on systems with P-states coordination
when one of the CPU cores is initialized after an offline/online
cycle triggered by user space. Both stable candidates, from Dirk
Brandewie.
- Fix for the ACPI video DMI blacklist entry for Dell Inspiron 7520
from Aaron Lu.
- Two new ACPI video blacklist entries for machines shipping with
Win8 that need to use native backlight so that it can be controlled
in a usual way (which doesn't work otherwise due bugs in the ACPI
tables) from Hans de Goede.
- Two ACPI _OSI quirks for systems that need them to work correctly
with Linux from Edward Lin and Hans de Goede"
* tag 'pm+acpi-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Revert native brightness quirk for ThinkPad T530
intel_pstate: remove setting P state to MAX on init
ACPICA: Tables: Restore old behavor to favor 32-bit FADT addresses.
ACPI / video: correct DMI tag for Dell Inspiron 7520
intel_pstate: Set turbo VID for BayTrail
ACPI / TPM: Fix resume regression on Chromebooks
ACPI / proc: Do not say when /proc interfaces will be deleted in Kconfig
ACPI / processor: do not mark present at boot but not onlined CPU as onlined
ACPI: Revert "ACPI / AC: convert ACPI ac driver to platform bus"
ACPI / blacklist: Add dmi_enable_osi_linux quirk for Asus EEE PC 1015PX
ACPI: blacklist win8 OSI for Dell Inspiron 7737
ACPI / video: Add use_native_backlight quirks for more systems
ACPI: Revert "ACPI / Battery: Remove battery's proc directory"
ACPI: Revert "ACPI: Remove CONFIG_ACPI_PROCFS_POWER and cm_sbsc.c"
ACPICA: Tables: Fix invalid pointer accesses in acpi_tb_parse_root_table().
Pull device mapper fixes from Mike Snitzer:
"A dm-crypt fix for a cpu hotplug crash that switches from using
per-cpu data to a mempool allocation (which offers allocation with cpu
locality, and there is no inter-cpu communication on slab allocation).
A couple dm-thinp stable fixes to address "out-of-data-space" issues.
A dm-multipath fix for a LOCKDEP warning introduced in 3.15-rc1"
* tag 'dm-3.15-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: fix lock order inconsistency in multipath_ioctl
dm thin: add timeout to stop out-of-data-space mode holding IO forever
dm thin: allow metadata commit if pool is in PM_OUT_OF_DATA_SPACE mode
dm crypt: fix cpu hotplug crash by removing per-cpu structure
Pull device tree fixes from Grant Likely:
"Drivercore bugfixes for v3.15
This branch contains bug fixes important to get into v3.15. There is
a fix for modifying properties seen during early boot, a fix for an
incorrect prototype when CONFIG_OF=n, and a couple of corrections to
device tree memory nodes on a few platforms"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
mips: dts: Fix missing device_type="memory" property in memory nodes
arm: dts: Fix missing device_type="memory" for ste-ccu8540
of: fix CONFIG_OF=n prototype of of_node_full_name()
of: make of_update_property() usable earlier in the boot process
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for various loose ends:
- Fix workarounds for R4000 erratum.
- Patch up DEC, Siemens-Nixdorf and Loongson hardware support.
- Wire up renameat2 syscall.
- Delete unused file - it was causing false warnings from maintenance
scripts.
- Revert a patch because it's functionality is now implemented twice
which causes superfluous /proc/cpuinfo output.
- Fix a microMIPS regression"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mm: Fix broken microMIPS kernel regression.
MIPS: Add new AUDIT_ARCH token for the N32 ABI on MIPS64
MIPS: Wire up renameat2 syscall.
MIPS: inst.h: Rename BITFIELD_FIELD to __BITFIELD_FIELD.
MIPS: Remove file missed when removing rm9k support a while ago.
MIPS/loongson2_cpufreq: Fix CPU clock rate setting
MIPS: Loongson: No need to select GENERIC_HARDIRQS_NO__DO_IRQ
MIPS: csum_partial.S CPU_DADDI_WORKAROUNDS bug fix
MIPS: __strncpy_from_user_asm CPU_DADDI_WORKAROUNDS bug fix
MIPS: __delay CPU_DADDI_WORKAROUNDS bug fix
MIPS: DEC/SNI: O32 wrapper stack switching fixes
MIPS: DEC: Bus error handler <asm/cpu-type.h> fixes
MAINTAINERS: TURBOchannel: Update entry
Revert "MIPS: MT: proc: Add support for printing VPE and TC ids"
Intel fixes for regressions, black screens and hangs, for 3.15.
* tag 'drm-intel-fixes-2014-05-16' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Increase WM memory latency values on SNB
drm/i915: restore backlight precision when converting from ACPI
drm/i915: Use the first mode if there is no preferred mode in the EDID
drm/i915/dp: force eDP lane count to max available lanes on BDW
drm/i915/vlv: reset VLV media force wake request register
drm/i915/SDVO: For sysfs link put directory and target in correct order
drm/i915: use lane count and link rate from VBT as minimums for eDP
drm/i915: clean up VBT eDP link param decoding
drm/i915: consider the source max DP lane count too
