[Why&How]
On amdgpu_dm_connector_destroy(), the driver attempts to cancel pending
HDMI HPD work without checking if the HDMI HPD is enabled.
Added a check that it is enabled before clearing it.
Fixes: 6a681cd903 ("drm/amd/display: Add an hdmi_hpd_debounce_delay_ms module")
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 17b2c526fd)
Analog connectors may be hot-plugged unlike other connector
types that don't support HPD.
Stop DRM from polling other connector types that don't
support HPD, such as eDP, LVDS, etc. These were wrongly
polled when analog connector support was added,
causing issues with the seamless boot process.
Fixes: c4f3f114e7 ("drm/amd/display: Poll analog connectors (v3)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reported-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e924c7004b)
[Why&How]
Right now, the HDMI HPD filter is enabled by default at 1500ms.
We want to disable it by default, as most modern displays with HDMI do
not require it for DPMS mode.
The HPD can instead be enabled as a driver parameter with a custom delay
value in ms (up to 5000ms).
Fixes: c918e75e1e ("drm/amd/display: Add an HPD filter for HDMI")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4859
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6a681cd903)
Internal backlight levels are initialised from ACPI but the values
are sometimes out of sync with the levels in effect until there has
been a read from hardware (eg triggered by reading from sysfs).
This means that the first drm_commit can cause the levels to be set
to a different value than the actual starting one, which results in
a sudden change in brightness.
This path shows the problem (when the values are out of sync):
amdgpu_dm_atomic_commit_tail()
-> amdgpu_dm_commit_streams()
-> amdgpu_dm_backlight_set_level(..., dm->brightness[n])
This patch calls the backlight ops get_brightness explicitly
at the end of backlight registration to make sure dm->brightness[n]
is in sync with the actual hardware levels.
Fixes: 2fe87f54ab ("drm/amd/display: Set default brightness according to ACPI")
Signed-off-by: Vivek Das Mohapatra <vivek@collabora.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 318b1c36d8)
Cc: stable@vger.kernel.org
[Why]
The PSR message was moved in commit 4321742c39 ("drm/amd/display:
Move PSR support message into amdgpu_dm"). This message however shows
for every single link without showing which link is which. This can
send a confusing message to the user.
[How]
Add link name into the message.
Fixes: 4321742c39 ("drm/amd/display: Move PSR support message into amdgpu_dm")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 99f77f6229)
Extra drm-misc-next for v6.19-rc1:
UAPI Changes:
- Add support for drm colorop pipeline.
- Add COLOR PIPELINE plane property.
- Add DRM_CLIENT_CAP_PLANE_COLOR_PIPELINE.
Cross-subsystem Changes:
- Attempt to use higher order mappings in system heap allocator.
- Always taint kernel with sw-sync.
Core Changes:
- Small fixes to drm/gem.
- Support emergency restore to drm-client.
- Allocate and release fb_info in single place.
- Rework ttm pipelined eviction fence handling.
Driver Changes:
- Support the drm color pipeline in vkms, amdgfx.
- Add NVJPG driver for tegra.
- Assorted small fixes and updates to rockchip, bridge/dw-hdmi-qp,
panthor.
- Add ASL CS5263 DP-to-HDMI simple bridge.
- Add and improve support for G LD070WX3-SL01 MIPI DSI, Samsung LTL106AL0,
Samsung LTL106AL01, Raystar RFF500F-AWH-DNN, Winstar WF70A8SYJHLNGA,
Wanchanglong w552946aaa, Samsung SOFEF00, Lenovo X13s panel.
- Add support for it66122 to it66121.
- Support mali-G1 gpu in panthor.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patch.msgid.link/aa5cbd50-7676-4a59-bbed-e8428af86804@linux.intel.com
This adds support for a multiplier. This multiplier is
programmed via the HDR Multiplier in DCN.
With this change the following IGT tests pass:
kms_colorop --run plane-XR30-XR30-multiply_125
kms_colorop --run plane-XR30-XR30-multiply_inv_125
The color pipeline now consists of the following colorops:
1. 1D curve colorop
2. 3x4 CTM
3. Multiplier
4. 1D curve colorop
5. 1D LUT
6. 1D curve colorop
7. 1D LUT
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20251115000237.3561250-42-alex.hung@amd.com
This adds support for a 3x4 color transformation matrix.
With this change the following IGT tests pass:
kms_colorop --run plane-XR30-XR30-ctm_3x4_50_desat
kms_colorop --run plane-XR30-XR30-ctm_3x4_overdrive
kms_colorop --run plane-XR30-XR30-ctm_3x4_oversaturate
kms_colorop --run plane-XR30-XR30-ctm_3x4_bt709_enc
kms_colorop --run plane-XR30-XR30-ctm_3x4_bt709_dec
The color pipeline now consists of the following colorops:
1. 1D curve colorop
2. 3x4 CTM
3. 1D curve colorop
4. 1D LUT
5. 1D curve colorop
6. 1D LUT
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20251115000237.3561250-40-alex.hung@amd.com
This patch adds colorops for custom 1D LUTs in the SHAPER and
BLND HW blocks.
With this change the following IGT tests pass:
kms_colorop --run plane-XR30-XR30-srgb_inv_eotf_lut
kms_colorop --run plane-XR30-XR30-srgb_inv_eotf_lut-srgb_eotf_lut
The color pipeline now consists of the following colorops:
1. 1D curve colorop
2. 1D curve colorop
3. 1D LUT
4. 1D curve colorop
5. 1D LUT
The 1D curve colorops support sRGB, BT2020, and PQ scaled to 125.0.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20251115000237.3561250-39-alex.hung@amd.com
This patchset enables support for the PQ_125 EOTF and its inverse
on all existing plane 1D curve colorops, i.e., on DEGAM, SHAPER,
and BLND blocks.
With this patchset the following IGT subtests are passing:
kms_colorop --run plane-XR30-XR30-pq_125_eotf
kms_colorop --run plane-XR30-XR30-pq_125_inv_eotf
kms_colorop --run plane-XR30-XR30-pq_125_eotf-pq_125_inv_eotf
kms_colorop --run plane-XR30-XR30-pq_125_eotf-pq_125_inv_eotf-pq_125_eotf
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20251115000237.3561250-33-alex.hung@amd.com
Expose a 3rd 1D curve colorop, with support for
DRM_COLOROP_1D_CURVE_SRGB_EOTF and program the BLND block
to perform the sRGB transform when the colorop is not in
bypass
With this change the following IGT test passes:
kms_colorop --run plane-XR30-XR30-srgb_eotf-srgb_inv_eotf-srgb_eotf
The color pipeline now consists of the following colorops:
1. 1D curve colorop w/ sRGB EOTF support
2. 1D curve colorop w/ sRGB Inverse EOTF support
3. 1D curve colorop w/ sRGB EOTF support
Signed-off-by: Alex Hung <alex.hung@amd.com>
Co-developed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20251115000237.3561250-31-alex.hung@amd.com
Expose a 2nd curve colorop with support for
DRM_COLOROP_1D_CURVE_SRGB_INV_EOTF and program HW to
perform the sRGB Inverse EOTF on the shaper block
when the colorop is not in bypass.
With this change the follow IGT tests pass:
kms_colorop --run plane-XR30-XR30-srgb_inv_eotf
kms_colorop --run plane-XR30-XR30-srgb_eotf-srgb_inv_eotf
The color pipeline now consists of the following colorops:
1. 1D curve colorop w/ sRGB EOTF support
2. 1D curve colorop w/ sRGB Inverse EOTF support
Signed-off-by: Alex Hung <alex.hung@amd.com>
Co-developed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patch.msgid.link/20251115000237.3561250-30-alex.hung@amd.com
The function dereferences amdgpu_dm_connector->dc_link early to
initialize verified_link_cap and dc, but later still checks
amdgpu_dm_connector->dc_link for NULL in the analog path.
This late NULL check is redundant, introduce a local dc_link pointer,
use it consistently, and drop the superfluous NULL check while using
dc_link->link_id.id instead.
The function uses dc_link at the very beginning without checking if it
is NULL. But later in the code, it suddenly checks if dc_link is NULL.
This check is too late to be useful, because the code has already used
dc_link earlier. So this NULL check does nothing.
We simplify the code by storing amdgpu_dm_connector->dc_link in a local
dc_link variable and using it throughout the function. Since dc_link is
already dereferenced early, the later NULL check is unnecessary and is
removed.
Fixes the below:
amdgpu_dm_connector_get_modes():
variable dereferenced before check 'amdgpu_dm_connector->dc_link'
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c
8845 &amdgpu_dm_connector->dc_link->verified_link_cap;
8846 const struct dc *dc = amdgpu_dm_connector->dc_link->dc;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Dereference
...
8856
8857 if (amdgpu_dm_connector->dc_sink &&
8858 amdgpu_dm_connector->dc_link &&
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Checked too late.
Presumably this NULL check could be removed?
...
Fixes: d46e422f65 ("drm/amd/display: Cleanup uses of the analog flag")
Reported by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Timur Kristóf <timur.kristof@gmail.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Existing routine has two conversion sequence,
pbn_to_kbps and kbps_to_pbn with margin.
Non of those has without-margin calculation.
kbps_to_pbn with margin conversion includes
fec overhead which has already been included in
pbn_div calculation with 0.994 factor considered.
It is a double counted fec overhead factor that causes
potential bw loss.
[How]
Add without-margin calculation.
Fix fec overhead double counted issue.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3735
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some monitors perform rapid “autoscan” HPD re‑assertions right after a
disconnect or powersaving mode enablement. These appear as a quick
disconnect→reconnect with an identical EDID. Since Linux has no HDMI
hotplug detection (HPD) filter, these quick reconnects are seen as hotplug
events, which can unintentionally wake a system with DPMS off.
An example: https://gitlab.freedesktop.org/drm/amd/-/issues/2876
Such 'fake reconnects' are considered when the interval between a
disconnect and a connect is within 1500ms (experimentally chosen using
several monitors), and the two connections have the same EDID.
[How]
Implement a time-based debounce mechanism:
1. On HDMI disconnect detection, instead of immediately processing the
HPD event, save the current sink and schedule delayed work (default 1500ms)
2. If another HDMI disconnect HPD event arrives during the debounce period,
it reschedules the pending work, ensuring only the final state is processed.
3. When the debounce timer expires, re-detect the display and compare the
new sink with the cached one using EDID comparison.
4. If sinks match (same EDID), this was a spontaneous HPD toggle:
- Update connector state internally
- Skip hotplug event to prevent desktop rearrangement
If sinks differ, this was a real display change:
- Process normally with the hotplug event
The debounce delay is configurable via module parameter
'hdmi_hpd_debounce_delay_ms'.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2876
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds the missing @aconnector, @connector, and @force descriptions:
@aconnector – This is the DM (Display Manager) connector. It gives
access to the DRM connector, the DC link, and hotplug/poll state. The
code uses it to check the link, update the sink, and manage connector
state changes.
@connector – This is the main DRM connector given by the DRM core.
Inside the detect function, it is converted to amdgpu_dm_connector so we
can run DC link detection, either light or full.
@force – This flag tells the function whether to run a full detect
again. If false, we avoid heavy DAC load detect steps to prevent
flicker. If true, we force a re-detect even when we normally skip it.
Fixes the below with gcc W=1:
function param 'aconnector' not described in 'amdgpu_dm_connector_poll'
function param 'force' not described in 'amdgpu_dm_connector_poll'
function param 'connector' not described in 'amdgpu_dm_connector_detect'
function param 'force' not described in 'amdgpu_dm_connector_detect'
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_dp_mst_topology_queue_probe() is used under the assumption that
mst is already initialized. If we connect system with SST first
then switch to the mst branch during suspend, we will fail probing
topology by calling the wrong API since the mst manager is yet to
be initialized.
[How]
At dm_resume(), once it's detected as mst branc connected, check if
the mst is initialized already. If not, call
dm_helpers_dp_mst_start_top_mgr() instead to initialize mst
V2: Adjust the commit msg a bit
Fixes: bc068194f5 ("drm/amd/display: Don't write DP_MSTM_CTRL after LT")
Cc: Fangzhi Zuo <jerry.zuo@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are some new changes for HDCP2 firmware locality check. The
implementation doesn't perfectly fit the intended design and clarity.
1. Clarify and consolidate variable responsibilities.
The previous implementation introduced the following variables:
- config.ddc.funcs.atomic_write_poll_read_i2c (optional pointer)
- hdcp->config.ddc.funcs.atomic_write_poll_read_aux (optional pointer)
- hdcp->connection.link.adjust.hdcp2.force_sw_locality_check (bool)
- hdcp->config.debug.lc_enable_sw_fallback (bool)
- use_fw (bool)
They will be used together to determine two operations:
- Whether to use FW locality check
- Whether to use SW fallback on FW locality check failure
The refactor streamlines this by introducing two variables in the hdcp2
link adjustment, while ensuring function pointers are always assigned
and remain independent from policy decisions:
- use_fw_locality_check (bool) -> true if fw locality should be used.
- use_sw_locality_fallback (bool) -> true to reset use_fw_locality_check
back to false and retry on fw locality check failure.
2. Mixed meanings of l_prime_read transition input
l_prime_read originally means if l_prime is read when sw locality check
is used. When FW locality check is used, l_prime_read means if lc init
write, l prime poll and l_prime read combo operation is successful. The
mix of meanings is confusing. The refactor introduces a new variable
l_prime_combo_read to isolate the second meaning into its own variable.
3. Missing specific error code on firmware locality error.
The original change reuses the generic DDC failure error code when
firmware fails to return locality check result. This is not ideal as
DDC failure indicates an error occurred during an I2C/AUX transaction.
FW locality failure could be caused by polling timeout in firmware or
failure to acquire firmware access. Which sits at a higher level of
abstraction above DDC hardware. An incorrect error code could mislead
the debug into a wrong direction.
4. Correcting misplaced comments. The previous implementation of the
firmware locality check resulted in some comments in hdcp2_transition
being incorrectly positioned. This refactor relocates those comments to
their appropriate locations for better clarity.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 978fa2f6d0 ("drm/amd/display: Use scaling for non-native
resolutions on eDP") started using the GPU scaler hardware to scale
when a non-native resolution was picked on eDP. This scaling was done
to fill the screen instead of maintain aspect ratio.
The idea was supposed to be that if a different scaling behavior is
preferred then the compositor would request it. The not following
aspect ratio behavior however isn't desirable, so adjust it to follow
aspect ratio and still try to fill screen.
Note: This will lead to black bars in some cases for non-native
resolutions. Compositors can request the previous behavior if desired.
Fixes: 978fa2f6d0 ("drm/amd/display: Use scaling for non-native resolutions on eDP")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4538
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we have an amdgpu_dm_connector->dc_sink first before
adding common modes for analog outputs. If we don't have a
sink yet we can safely skip this.
Fixes: 70181ad96e ("drm/amd/display: Add common modes to analog displays without EDID")
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VRR is not supported on analog signals.
Don't add freesync modes to analog displays or when
VRR is unsupported by DC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the EDID of an analog display is not available, we can't
know the possible modes supported by the display. However, we
still need to offer the user to select from a variety of common
modes. It will be up to the user to select the best one, though.
This is how it works on other operating systems as well as the
legacy display code path in amdgpu.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This feature is useful for analog connections without EDID:
- Really old monitors with a VGA connector
- Cheap DVI/VGA adapters that don't connect DDC pins
When a connection is established through DAC load detection,
the driver is supposed to fill in the supported modes for the
display, which we already do in amdgpu_dm_connector_get_modes.
Also, because the load detection causes visible glitches, do not
attempt to poll the connector again after it was detected this
way. Note that it will still be polled after sleep/resume or
when force is enabled, which is okay.
v2:
Add dc_connection_dac_load connection type.
Properly release sink when no display is connected.
Don't print error when EDID isn't read from an analog display.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
