[Why]
Currently driver enables dmub outbox notification before oubox ISR is
registered. During boot scenario, sometimes dmub issues hpd outbox
message before driver registers ISR and those messages are missed.
[How]
Enable dmub outbox notification after outbox ISR is registered. Also,
restructured outbox enable code to call from dm layer and renamed APIs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pm sysfs should be writable in one VF mode as is in passthrough
[how]
do not remove write access on pm sysfs if device is in one VF mode
Fixes: 11c9cc95f8 ("amdgpu/pm: Make sysfs pm attributes as read-only for VFs")
Signed-off-by: Yiqing Yao <yiqing.yao@amd.com>
Reviewed-by: Monk Liu <Monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Some ASICs, with the PMFW default settings, we may see the
power consumption reported via metrics table is "Very Erratic".
With the socket power alpha filter set as 10/100ms, we can correct
that issue.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang static analysis reports this problem
amdgpu_ctx.c:616:26: warning: Assigned value is garbage
or undefined
args->out.pstate.flags = stable_pstate;
^ ~~~~~~~~~~~~~
amdgpu_ctx_stable_pstate can fail without setting
stable_pstate. So check.
Fixes: 8cda7a4f96 ("drm/amdgpu/UAPI: add new CTX OP to get/set stable pstates")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DCN3/3.01/3.02 at least these use the fpu.
v2: squash in build fix for when DCN is not enabled (Leo)
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Registers that exist within the MCH BAR and are mirrored into the GPU's
MMIO space are a good candidate to separate out into their own header.
For reference, the mirror of the MCH BAR starts at the following
locations in the graphics MMIO space (the end of the MCHBAR range
differs slightly on each platform):
* Pre-gen6: 0x10000
* Gen6-Gen11 + RKL: 0x140000
v2:
- Create separate patch to swtich a few register definitions to be
relative to the MCHBAR mirror base.
- Drop upper bound of MCHBAR mirror from commit message; there are too
many different combinations between various platforms to list out,
and the documentation is spotty for the older pre-gen6 platforms
anyway.
Bspec: 134, 51771
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220215061342.2055952-2-matthew.d.roper@intel.com
The random order of register definitions we have today causes a lot of
confusion and unintentional duplication when new registers/bits are
added to the driver. Let's order the GT register file by MMIO offset
A couple duplicated/unused register definitions are dropped while doing
this re-order: GEN11_GT_INTR_DW{0,1}, GEN11_IIR_REG{0,1}_SELECTOR, and
GEN11_INTR_IDENTITY_REG{0,1} aren't used anywhere in the driver because
we have other parameterized macros referencing those registers.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209051140.1599643-7-matthew.d.roper@intel.com
There's a lot of inconsistent spacing and indentation in our register
definitions. Let's clean things up a bit and follow some consistent
rules:
* "#define" always starts in column 0
* There's exactly one space between '#define' and the name of a
register.
* There's exactly three spaces between '#define' and the name of a
bit/bitfield.
* Tabs (no spaces) are used between a definition name and its value;
the value starts on column 48 unless the name is too long, in which
case a single tab is used.
Final diff for this patch is empty if whitespace is ignored:
$ git diff -w
$
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209051140.1599643-5-matthew.d.roper@intel.com
These SFC registers were defined in an unusual way, taking an engine as
a parameter rather than an engine MMIO base offset. Let's adjust them
to match the style used by other per-engine registers and move them to
intel_engine_regs.h.
While doing this move, we can drop GEN12_HCP_SFC_FORCED_LOCK completely;
it was intended for use in an early version of a hardware workaround,
but was no longer necessary by the time the workaround was finalized.
It is not used anywhere in the driver.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209051140.1599643-3-matthew.d.roper@intel.com
Mipi dsi panel drivers can use mipi_dsi_dcs_{set,get}_display_brightness()
to request backlight changes.
This can be done during panel initialization (dsi is in command mode)
or afterwards (dsi is in Video Mode).
When the DSI is in Video Mode, all commands are rejected.
Detect current DSI mode in mtk_dsi_host_transfer() and switch modes
temporarily to allow commands to be sent.
Signed-off-by: Julien STEPHAN <jstephan@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add support to convert from XR24 to reversed monochrome for drivers that
control monochromatic display panels, that only have 1 bit per pixel.
The function does a line-by-line conversion doing an intermediate step
first from XR24 to 8-bit grayscale and then to reversed monochrome.
The drm_fb_gray8_to_mono_reversed_line() helper was based on code from
drivers/gpu/drm/tiny/repaper.c driver.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133710.3278506-3-javierm@redhat.com
Recently we added generic "edp-panel"s probed by EDID. To support
panels in this way we look at the panel ID in the EDID and look up the
panel in a table that has power sequence timings. If we find a panel
that's not in the table we will still attempt to use it but we'll use
conservative timings. While it's likely that these conservative
timings will work for most nearly all panels, the performance of
turning the panel off and on suffers.
We'd like to be able to reliably detect the case that we're using the
hardcoded timings without relying on parsing dmesg. This allows us to
implement tests that ensure that no devices get shipped that are
relying on the conservative timings.
Let's add a new debugfs entry to panel devices. It will have one of:
* UNKNOWN - We tried to detect a panel but it wasn't in our table.
* HARDCODED - We're not using generic "edp-panel" probed by EDID.
* A panel name - This is the name of the panel from our table.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.3.I209d72bcc571e1d7d6b793db71bf15c9c0fc9292@changeid
We'd like panels to be able to add things to debugfs underneath the
connector's directory. Let's plumb it through. A panel will be able to
put things in a "panel" directory under the connector's
directory. Note that debugfs is not ABI and so it's always possible
that the location that the panel gets for its debugfs could change in
the future.
NOTE: this currently only works if you're using a modern
architecture. Specifically the plumbing relies on _both_
drm_bridge_connector and drm_panel_bridge. If you're not using one or
both of these things then things won't be plumbed through.
As a side effect of this change, drm_bridges can also get callbacks to
put stuff underneath the connector's debugfs directory. At the moment
all bridges in the chain have their debugfs_init() called with the
connector's root directory.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.2.Ib0bd5346135cbb0b63006b69b61d4c8af6484740@changeid
The ti-sn65dsi86 driver shouldn't hand-roll its own bridge
connector. It should use the normal drm_bridge_connector. Let's switch
to do that, removing all of the custom code.
NOTE: this still _doesn't_ implement DRM_BRIDGE_ATTACH_NO_CONNECTOR
support for ti-sn65dsi86 and that would still be a useful thing to do
in the future. It was attempted in the past [1] but put on the back
burner. However, unless we instantly change ti-sn65dsi86 fully from
not supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR at all to _only_
supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR then we'll still need a bit
of time when we support both. This is a better way to support the old
way where the driver hand rolls things itself.
A new notes about the implementation here:
* When using the drm_bridge_connector the connector should be created
after all the bridges, so we change the ordering a bit.
* I'm reasonably certain that we don't need to do anything to "free"
the new drm_bridge_connector. If drm_bridge_connector_init() returns
success then we know drm_connector_init() was called with the
`drm_bridge_connector_funcs`. The `drm_bridge_connector_funcs` has a
.destroy() that does all the cleanup. drm_connector_init() calls
__drm_mode_object_add() with a drm_connector_free() that will call
the .destroy().
* I'm also reasonably certain that I don't need to "undo" the
drm_bridge_attach() if drm_bridge_connector_init() fails. The
"detach" function is private and other similar code doesn't try to
undo the drm_bridge_attach() in error cases. There's also a comment
indicating the lack of balance at the top of drm_bridge_attach().
[1] https://lore.kernel.org/r/20210920225801.227211-4-robdclark@gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.1.I3ab26b7f197cc56c874246a43e57913e9c2c1028@changeid
Get rid of the inflexible bigjoiner_linked_crtc pointer thing
and just track things as a bitmask of pipes instead. We can
also nuke the bigjoiner_slave boolean as the role of the pipe
can be determined from its position in the bitmask.
It might be possible to nuke the bigjoiner boolean as well
if we make encoder.compute_config() do the bitmask assignment
directly for the master pipe. But for now I left that alone so
that encoer.compute_config() will just flag the state as needing
bigjoiner, and the intel_atomic_check_bigjoiner() is still
responsible for determining the bitmask. But that may have to change
as the encoder may be in the best position to determine how
exactly we should populate the bitmask.
Most places that just looked at the single bigjoiner_linked_crtc
now iterate over the whole bitmask, eliminating the singular
slave pipe assumption.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203183823.22890-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
[why]
In LTTPR non-transparent mode, we need
to reset the cached lane settings before performing
link training on the next PHY repeater. Otherwise,
the cached lane settings will be used for the next
clock recovery e.g. VS = MAX (3) which should not be
the case according to the DP specs. We expect to use
minimum lane settings on each clock recovery sequence.
[how]
Reset DPCD and HW lane settings on each repeater LT.
Set training pattern to 0 for the repeater that failed LT
at the proper place.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The KFD only unmaps all queues, all dynamics queues or all process queues
since RUN_LIST is mapped with all KFD queues.
There's no need to provide a single type unmap so remove this option.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch handles the GPU recovery failure in sriov environment by
retrying the reset if the first reset fails. To determine the condition
of retry, a new macro AMDGPU_RETRY_SRIOV_RESET is added which returns
true if failure is due to ETIMEDOUT, EINVAL or EBUSY, otherwise return
false.A new macro AMDGPU_MAX_RETRY_LIMIT is used to limit the retry to 2.
It also handles the return status in Post Asic Reset by updating the return
code with asic_reset_res and eventually return the return code in
amdgpu_job_timedout().
Signed-off-by: Surbhi Kakarya <surbhi.kakarya@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
