Issue is seen when PSR enabled with setup frames and when try to disable
PSR at SRDONACK State (0x1). PSR FSM is stuck at SRDONACK(0x1) for more
than 5 seconds. Issue not seen with Setup frames disabled. Currently
disable psr1 if setuptime > vblank to workaround the above issue.
HSD: 16024594674
WA: 18037818876
v1: Initial version
v2: Add debug log and some cosmetic changes. [Jouni, Jani, Nemesa]
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241105103916.1857731-1-animesh.manna@intel.com
Having Panel Replay enabled together with VRR is causing following errors:
xe 0000:00:02.0: [drm] *ERROR* Timed out waiting PSR idle state
xe 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
xe 0000:00:02.0: [drm] *ERROR* CPU pipe A FIFO underrun
xe 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00040080
xe 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00040080
Let's disable Panel Replay as well if VRR is enabled.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241031081025.3215966-1-jouni.hogander@intel.com
We are currently seeing unexpected link trainings with several different
eDP panels. These are caused by these panels stating bad link status in
their dpcd registers. This can be observed by doing following test:
1. Boot up without Xe module loaded
2. Load Xe module with PSR disabled:
$ modprobe xe enable_psr=0
3. Read panel link status register
$ dpcd_reg read --offset 0x200e --count=1
0x200e: 00
4. Enable PSR, sleep for 2 seconds and disable PSR again:
$ echo 0x1 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
$ echo "-1" > /sys/kernel/debug/dri/0000:00:02.0/xe_params/enable_psr
$ echo 0x0 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
$ sleep 2
$ cat /sys/kernel/debug/dri/0/i915_edp_psr_status | grep status
$ echo 0x1 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
Source PSR/PanelReplay status: DEEP_SLEEP [0x80310030]
5. Now read panel link status registers again:
$ dpcd_reg read --offset 0x200e --count=1
0x200e: 80
Workaround this by not trusting link status registers after PSR is enabled
until first short pulse interrupt is received.
v2:
- clear link_ok flag on pipe disable
- remove useless comment
- modify intel_dp_needs_link_retrain return statement
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029122415.1789528-1-jouni.hogander@intel.com
Use x100, or ver * 100 + rel, versions for full IP version checks,
similar to what xe driver does:
- Replace IP_VER(14, 1) inline with 1401, etc.
- Convert DISPLAY_VER_FULL() to DISPLAY_VERx100()
- Convert IS_DISPLAY_VER_FULL() to IS_DISPLAY_VERx100()
- Convert IS_DISPLAY_VER_STEP() to IS_DISPLAY_VERx100_STEP()
This makes ver.rel versions easier to use, follows the xe driver
pattern, and drops the dependency on the IP_VER() macro.
v2: Rebase, drop IP_VER() from xe compat headers
v3: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029155536.753413-1-jani.nikula@intel.com
To reach PC10 when PKG_C_LATENCY is configure we must do the following
things
1) Enter PSR1 only when delayed_vblank < 6 lines and DC5 can be entered
2) Allow PSR2 deep sleep when DC5 can be entered
3) DC5 can be entered when all transocoder have either PSR1, PSR2 or
eDP 1.5 PR ALPM enabled and VBI is disabled and flips and pushes are
not happening.
--v2
-Switch condition and do an early return [Jani]
-Do some checks in compute_config [Jani]
-Do not use register reads as a method of checking states for
DPKGC or delayed vblank [Jani]
-Use another way to see is vblank interrupts are disabled or not [Jani]
--v3
-Use has_psr to check if psr can be enabled or not for dc5_entry cond
[Uma]
-Move the dc5 entry computation to psr_compute_config [Jouni]
-No need to change sequence of enabled and activate,
so dont make hsw_psr1_activate return anything [Jouni]
-Use has_psr to stop psr1 activation [Jouni]
-Use lineage no. in WA
-Add the display ver restrictions for WA
--v4
-use more appropriate name for check_vblank_limit() [Jouni]
-Cover the case for idle frames when dpkgc is not configured [Jouni]
-Check psr only for edp [Jouni]
--v5
-move psr1 handling to plane update [Jouni]
-add todo for cases when vblank is enabled when psr enabled [Jouni]
-use intel_display instead of drm_i915_private
--v6
-check target_dc_state [Jouni]
-fix condition in pre/post plane update [Jouni]
--v7
-fix has_psr condition [Uma]
-fix typo in commit subject [Uma]
-put psr1_wa check in its own helper [Uma]
-fix the dc_entry check [Jouni]
-use HAS_PSR() to cover two edp one with psr and one nonpsr [Jouni]
WA: 22019444797
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240920091203.1043308-2-suraj.kandpal@intel.com
Panel Self Refresh on eDP requires the AUX IO power to be enabled
whenever the output (main link) is enabled. This is required by the
AUX_PHY_WAKE/ML_PHY_LOCK signaling initiated by the HW automatically to
re-enable the main link after it got disabled in power saving states
(see eDP v1.4b, sections 5.1, 6.1.3.3.1.1).
The Panel Replay mode on non-eDP outputs on the other hand is only
supported by keeping the main link active, thus not requiring the above
AUX_PHY_WAKE/ML_PHY_LOCK signaling (eDP v1.4b, section 6.1.3.3.1.2).
Thus enabling the AUX IO power for this case is not required either.
Based on the above enable the AUX IO power only for eDP/PSR outputs.
Bspec: 49274, 53370
v2:
- Add a TODO comment to adjust the requirement for AUX IO based on
whether the ALPM/main-link off mode gets enabled. (Rodrigo)
Cc: Animesh Manna <animesh.manna@intel.com>
Fixes: b8cf5b5d26 ("drm/i915/panelreplay: Initializaton and compute config for panel replay")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240910111847.2995725-1-imre.deak@intel.com
We do not have ALPM on DP Panel Replay. Due to this SRD_STATUS[SRD State]
doesn't change from SRDENT_ON after Panel Replay is enabled until it gets
disabled.
On eDP Panel Replay DEEP_SLEEP is not reached.
_psr2_ready_for_pipe_update_locked is waiting DEEP_SLEEP bit getting reset.
Take these into account in Panel Replay code by not waiting PSR getting
idle after enabling VBI.
Fixes: 29fb595d48 ("drm/i915/psr: Panel replay uses SRD_STATUS to track it's status")
Cc: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240906070033.289015-5-jouni.hogander@intel.com
Use a forward declaration for struct cec_notifier instead of including
media/cec-notifier.h in intel_display_types.h, and only include it where
needed.
Also realize that a lot of places depend on including linux/debugfs.h
via intel_display_types.h -> media/cec-notifier.h -> media/cec.h, and
include that too where needed.
v2: hsw_ips.c also needs debugfs.h (kernel test robot)
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240827104521.4151471-1-jani.nikula@intel.com
eDP1.5 support ALPM with Panel Replay as well. We need to check ALPM
related things for Panel Replay as well.
Bspec: 68920
v5:
- instead of using crtc_state->has_panel_replay provide aux_less flag
v4:
- do not move _compute_psr2_sdp_prior_scanline_indication
- move ALPM related checks to separate function
v3: move vblank check as well
v2: do not move Vblank >= PSR2_CTL Block Count Number maximum line count
check
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-9-jouni.hogander@intel.com
Currently PSR2 SU Region Early Transport is enabled by default on Lunarlake
if panel supports it despite enable_psr module parameter value. This patch
makes it possible for user to limit used PSR mode and prevent SU Region
Early Transport by setting enable_psr as 2. With default (-1) PSR2 SU
Region Early Transport is allowed.
v2: fix/improve commit desciption
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240618053026.3268759-6-jouni.hogander@intel.com
If user is specifically limiting PSR mode to PSR1 or PSR2: disable Panel
Replay. With default value -1 all modes are allowed including Panel
Replay. Disabling PSR using value 0 disables Panel Replay as well.
Also own compute config helper is added for Panel Replay. This makes sense
because number of Panel Replay specific checks are increasing.
v2: Squash adding Panel Replay compute config helper
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240618053026.3268759-5-jouni.hogander@intel.com
SU SDP scanline indication should be taken into account when checking
vblank length. In Bspec we have:
PSR2_CTL[ SU SDP scanline indication ] = 0: (TRANS_VBLANK Vertical Blank
End- TRANS_VBLANK Vertical Blank Start) > PSR2_CTL Block Count Number value
in lines
PSR2_CTL[ SU SDP scanline indication ] = 1: (TRANS_VBLANK Vertical Blank
End- TRANS_VBLANK Vertical Blank Start- 1) > PSR2_CTL Block Count Number
value in lines
Bspec: 49274
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-12-jouni.hogander@intel.com
