Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
A few more Qualcomm driver updates for v6.13
Make the Adreno driver invoke the SMMU aperture setup firmware function,
which is required to allow the GPU to manage per-process page tables in
some firmware versions - as an example Rb3Gen2 has no GPU without this.
Add X1E Devkit to the list of devices that has functional EFI variable
access through the uefisecapp.
Flip the "manual slice configuration quirk" in the Qualcomm LLCC driver,
as this only applies to a single platform, and introduce support for
QCS8300, QCS615, SAR2130P, and SAR1130P.
Lastly, add IPQ5424 and IPQ5404 to the Qualcomm socinfo driver.
* tag 'qcom-drivers-for-6.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
soc: qcom: llcc: Add configuration data for QCS615
dt-bindings: cache: qcom,llcc: Document the QCS615 LLCC
soc: qcom: llcc: add support for SAR2130P and SAR1130P
soc: qcom: llcc: use deciman integers for bit shift values
dt-bindings: cache: qcom,llcc: document SAR2130P and SAR1130P
Link: https://lore.kernel.org/r/20241113032425.356306-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit c14e64b469 ("soc: qcom: llcc: Support chipsets that can write
to llcc") made the code not configure certain registers on SDM845 due
to firmware security policies. That turned out only to concern SDM845,
but the condition was chosen such that all other entries (for SoCs that
didnot need it) were required to set .need_llcc_cfg = true.
Flip the condition, so the default is "doesn't need the workaround".
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241104-topic-llcc_flip-v1-1-3003c846d131@oss.qualcomm.com
[bjorn: Dropped a few newly added need_llcc_cfg uses]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm driver updates for v6.13
Enable QSEECOM, and thereby access to EFI variables, for Lenovo Yoga
Slim 7x, Dell XPS 13, Microsoft Surface Pro 9.
Last Level Cache Controller (LLCC) driver code is shuffled, to improve
readability of the tables.
The Qualcomm socinfo driver gains support for QCS615, QCS9100, SAR1130P,
SAR2130P, and SA8255P.
A few drivers are simplified using dev_err_probe() and guard(), and a
few kernel-doc issues are corrected.
Mentioning of the #linux-msm IRC channel is added to the MAINTAINERS
file.
* tag 'qcom-drivers-for-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (30 commits)
soc: qcom: socinfo: add QCS9100 ID
dt-bindings: arm: qcom,ids: add SoC ID for QCS9100
dt-bindings: soc: qcom,aoss-qmp: Document the QCS8300 AOSS channel
dt-bindings: soc: qcom: add qcom,qcs8300-imem compatible
dt-bindings: firmware: qcom,scm: document SCM on QCS8300 SoCs
soc: qcom: socinfo: add support for SA8255P
dt-bindings: arm: qcom: add the SoC ID for SA8255P
soc: qcom: smp2p: Simplify code with dev_err_probe()
soc: qcom: smem: Simplify code with dev_err_probe()
soc: qcom: rpmh-rsc: Simplify code with dev_err_probe()
dt-bindings: soc: qcom: aoss-qmp: document support for SA8255p
dt-bindings: firmware: qcom,scm: document support for SA8255p
dt-bindings: soc: qcom,aoss-qmp: Add SAR2130P compatible
dt-bindings: firmware: qcom,scm: Add SAR2130P compatible
soc: qcom: socinfo: add SoC IDs for SAR1130P and SAR2130P
dt-bindings: arm: qcom,ids: add SoC ID for SAR2130P and SAR1130P
dt-bindings: soc: qcom: aoss-qmp: Add SM8750
soc: qcom: socinfo: Add QCS615 SoC ID table entry
dt-bindings: arm: qcom,ids: add SoC ID for QCS615
soc: qcom: smem: Fix up kerneldoc
...
Link: https://lore.kernel.org/r/20241102231953.871067-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/soc to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way do a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Herve Codina <herve.codina@bootlin.com> # for fsl/qe/{qmc,tsa}.c
Acked-by: Bjorn Andersson <andersson@kernel.org> # qcom parts
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au> # aspeed
Link: https://lore.kernel.org/r/20241029074859.509587-2-u.kleine-koenig@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On most modern qualcomm SoCs, the configuration necessary to enable the
Tag/Data RAM related irqs being propagated to the SoC irq controller is
already done in firmware (in DSF or 'DDR System Firmware')
On some like the x1e80100, these registers aren't even accesible to the
kernel causing a crash when edac device is probed.
Hence, make the irq configuration optional in the driver and mark x1e80100
as the SoC on which this should be avoided.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Reported-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240903101510.3452734-1-quic_rjendra@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Until SM8450, there was only one broadcast region (Broadcast_OR)
used to broadcast write and check for status bit 0.
>From SM8450 onwards another broadcast region (Broadcast_AND) has been
added which checks for status bit 1. This hasn't been updated and
Broadcast_OR region was wrongly being used to check for status bit 1 all
along.
Hence define new regmap structure for Broadcast_AND region and initialize
this regmap when HW block version is greater than 4.1, otherwise
initialize as a NULL pointer for backwards compatibility.
Switch from broadcast_OR to broadcast_AND region (when defined in DT)
for checking status bit 1 as Broadcast_OR region checks only for bit 0.
Signed-off-by: Unnathi Chalicheemala <quic_uchalich@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/9cf19928a67eaa577ae0f02de5bf86276be34ea2.1717014052.git.quic_uchalich@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Commit c14e64b469 ("soc: qcom: llcc: Support chipsets that can
write to llcc") add the support for chipset where capacity based
allocation and retention through power collapse can be programmed
based on content of SCT table mentioned in the llcc driver where
the target like sdm845 where the entire programming related to it
is controlled in firmware. However, the commit introduces a bug
where capacity/retention register get overwritten each time it
gets programmed for each slice and that results in misconfiguration
of the register based on SCT table and that is not expected
behaviour instead it should be read modify write to retain the
configuration of other slices.
This issue is totally caught from code review and programming test
and not through any power/perf numbers so, it is not known what
impact this could make if we don't have this change however,
this feature are for these targets and they should have been
programmed accordingly as per their configuration mentioned in
SCT table like others bits information.
This change brings one difference where it keeps capacity/retention
bits of the slices that are not mentioned in SCT table in unknown
state where as earlier it was initialized to zero.
Fixes: c14e64b469 ("soc: qcom: llcc: Support chipsets that can write to llcc")
Signed-off-by: Atul Dhudase <quic_adhudase@quicinc.com>
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1701876771-10695-1-git-send-email-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230925095532.1984344-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714175142.4067795-1-robh@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pull ARM SoC driver updates from Arnd Bergmann:
"The most notable updates this time are for Qualcomm Snapdragon
platforms. The Inline-Crypto-Engine gets a new DT binding and driver,
and a number of drivers now support additional Snapdragon variants, in
particular the rsc, scm, geni, bwm, glink and socinfo, while the llcc
(edac) and rpm drivers get notable functionality updates.
Updates on other platforms include:
- Various updates to the Mediatek mutex and mmsys drivers, including
support for the Helio X10 SoC
- Support for unidirectional mailbox channels in Arm SCMI firmware
- Support for per cpu asynchronous notification in OP-TEE firmware
- Minor updates for memory controller drivers.
- Minor updates for Renesas, TI, Amlogic, Apple, Broadcom, Tegra,
Allwinner, Versatile Express, Canaan, Microchip, Mediatek and i.MX
SoC drivers, mainly updating the use of MODULE_LICENSE() macros and
obsolete DT driver interfaces"
* tag 'soc-drivers-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: ti: smartreflex: Simplify getting the opam_sr pointer
bus: vexpress-config: Add explicit of_platform.h include
soc: mediatek: Kconfig: Add MTK_CMDQ dependency to MTK_MMSYS
memory: mtk-smi: mt8365: Add SMI Support
dt-bindings: memory-controllers: mediatek,smi-larb: add mt8365
dt-bindings: memory-controllers: mediatek,smi-common: add mt8365
memory: tegra: read values from correct device
dt-bindings: crypto: Add Qualcomm Inline Crypto Engine
soc: qcom: Make the Qualcomm UFS/SDCC ICE a dedicated driver
dt-bindings: firmware: document Qualcomm QCM2290 SCM
soc: qcom: rpmh-rsc: Support RSC v3 minor versions
soc: qcom: smd-rpm: Use GFP_ATOMIC in write path
soc/tegra: fuse: Remove nvmem root only access
soc/tegra: cbb: tegra194: Use of_address_count() helper
soc/tegra: cbb: Remove MODULE_LICENSE in non-modules
ARM: tegra: Remove MODULE_LICENSE in non-modules
soc/tegra: flowctrl: Use devm_platform_get_and_ioremap_resource()
soc: tegra: cbb: Drop empty platform remove function
firmware: arm_scmi: Add support for unidirectional mailbox channels
dt-bindings: firmware: arm,scmi: Support mailboxes unidirectional channels
...
The Qualcomm LLCC/EDAC drivers were using a fixed register stride for
accessing the (Control and Status Registers) CSRs of each LLCC bank.
This stride only works for some SoCs like SDM845 for which driver
support was initially added.
But the later SoCs use different register stride that vary between the
banks with holes in-between. So it is not possible to use a single register
stride for accessing the CSRs of each bank. By doing so could result in a
crash.
For fixing this issue, let's obtain the base address of each LLCC bank from
devicetree and get rid of the fixed stride. This also means, there is no
need to rely on reg-names property and the base addresses can be obtained
using the index.
First index is LLCC bank 0 and last index is LLCC broadcast. If the SoC
supports more than one bank, then those need to be defined in devicetree
for index from 1..N-1.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Steev Klimaszewski <steev@kali.org> # Thinkpad X13s
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-13-manivannan.sadhasivam@linaro.org
The LLCC EDAC register offsets varies between each SoCs. Until now, the
EDAC driver used the hardcoded register offsets. But this caused crash
on SM8450 SoC where the register offsets has been changed.
So to avoid this crash and also to make it easy to accommodate changes for
new SoCs, let's pass the LLCC version specific register offsets to the
EDAC driver.
Currently, two set of offsets are used. One is starting from LLCC version
v1.0.0 used by all SoCs other than SM8450. For SM8450, LLCC version
starting from v2.1.0 is used.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220825043859.30066-3-manivannan.sadhasivam@linaro.org
The register offsets used by the LLCC block retains its layout for multiple
versions. For instance, starting from version v1.0.0 to v2.0.1 the offsets
are same. And starting from v2.1.0, the offsets changed.
But the current reg_offset naming convention is confusing. So to reflect
this change correctly in driver, let's encode the start version from which
the offsets got changed in reg_offset struct name. This will be
llcc_v1_reg_offset for v1.0.0 and llcc_v2_1_reg_offset for v2.1.0.
This will allow multiple SoCs to use the same reg_offset clearly.
And in the future if the offsets got changed again, then that specific
version could be encoded in the struct name.
Suggested-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220825043859.30066-2-manivannan.sadhasivam@linaro.org
LLCC HW version info is made up of major, branch, minor and echo
version bits each of which are 8bits. Several features in newer
LLCC HW are based on the full version rather than just major or
minor versions such as write-subcache enable which is applicable
for versions v2.0.0.0 and later, also upcoming write-subcache
cacheable for SM8450 SoC which is only present in versions v2.1.0.0
and later, so it makes it easier and cleaner to just directly
compare with the full version than adding additional major/branch/
minor/echo version checks. So remove the earlier major version check
and add full version check for those features.
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/a82d7c32348c51fcc2b63e220d91b318bf706c83.1643355594.git.quic_saipraka@quicinc.com
