Pull more thermal control updates from Rafael Wysocki:
"These are mostly assorted updates of thermal drivers used on ARM
platforms:
- Use dev_err_probe() helpers to simplify the init code in the Qoriq
thermal driver (Frank Li)
- Power down the Qoriq's TMU at suspend time (Alice Guo)
- Add ipq5332, ipq5424 compatible to the QCom's tsens thermal driver
and TSENS enable / calibration support for V2 (Praveenkumar I)
- Add missing rk3328 mapping entry (Trevor Woerner)
- Remove duplicate struct declaration from the thermal core header
file (Xueqin Luo)
- Disable the monitoring mode during suspend in the LVTS Mediatek
driver to prevent temperature acquisition glitches (Nícolas F. R.
A. Prado)
- Disable Stage 3 thermal threshold in the LVTS Mediatek driver
because it disables the suspend ability and does not have an
interrupt handler (Nícolas F. R. A. Prado)
- Fix low temperature offset interrupt in the LVTS Mediatek driver to
prevent multiple interrupts from triggering when the system is at
its normal functionning temperature (Nícolas F. R. A. Prado)
- Enable interrupts in the LVTS Mediatek driver only on sensors that
are in use (Nícolas F. R. A. Prado)
- Add the BCM74110 compatible DT binding and the corresponding code
to support a chip based on a different process node than previous
chips (Florian Fainelli)
- Correct indentation and style in DTS example (Krzysztof Kozlowski)
- Unify hexadecimal annotatation in the rcar_gen3 driver (Niklas
Söderlund)
- Factor out the code logic to read fuses on Gen3 and Gen4 in the
rcar_gen3 thermal driver (Niklas Söderlund)
- Drop unused driver data from the QCom's spmi temperature alarm
driver (Johan Hovold)"
* tag 'thermal-6.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/drivers/qcom-spmi-temp-alarm: Drop unused driver data
thermal: rcar_gen3: Reuse logic to read fuses on Gen3 and Gen4
thermal: rcar_gen3: Use lowercase hex constants
dt-bindings: thermal: Correct indentation and style in DTS example
thermal/drivers/brcmstb_thermal: Add support for BCM74110
dt-bindings: thermal: Update for BCM74110
thermal/drivers/mediatek/lvts: Only update IRQ enable for valid sensors
thermal/drivers/mediatek/lvts: Start sensor interrupts disabled
thermal/drivers/mediatek/lvts: Disable low offset IRQ for minimum threshold
thermal/drivers/mediatek/lvts: Disable Stage 3 thermal threshold
thermal/drivers/mediatek/lvts: Disable monitor mode during suspend
thermal: core: Remove duplicate struct declaration
thermal/drivers/rockchip: Add missing rk3328 mapping entry
thermal/drivers/tsens: Add TSENS enable and calibration support for V2
dt-bindings: thermal: tsens: Add ipq5332, ipq5424 compatible
thermal/drivers/qoriq: Power down TMU on system suspend
thermal/drivers/qoriq: Use dev_err_probe() simplify the code
Pull devicetree updates from Rob Herring:
"DT Bindings:
- Drop duplicate devices in trivial-devices.yaml
- Add a common serial peripheral device schema and reference it in
serial device schemas.
- Convert nxp,lpc1850-wdt, zii,rave-wdt, ti,davinci-wdt,
snps,archs-pct, fsl,bcsr, fsl,fpga-qixis-i2c, fsl,fpga-qixis,
fsl,cpm-enet, fsl,cpm-mdio, fsl,ucc-hdlc, maxim,ds26522,
aspeed,ast2400-cvic, aspeed,ast2400-vic, fsl,ftm-timer,
ti,davinci-timer, fsl,rcpm, and qcom,ebi2 to DT schema
- Add support for rockchip,rk3576-wdt, qcom,apss-wdt-sa8255p,
fsl,imx8qm-irqsteer, qcom,pm6150-vib, qcom,sa8255p-pdc,
isil,isl69260, ti,tps546d24, and lpc32xx DMA mux
- Drop duplicate nvidia,tegra186-ccplex-cluster.yaml and
mediatek,mt6795-sys-clock.yaml
- Add arm,gic ESPI and EPPI interrupt type specifiers
- Add another batch of legacy compatible strings which we have no
intention of documenting
- Add dmas/dma-names properties to FSL lcdif
- Fix wakeup-source reference to m8921-keypad.yaml
- Treewide fixes of typos in bindings
DT Core:
- Update dtc/libfdt to upstream version v1.7.0-95-gbcd02b523429
- More conversions to scoped iterators and __free() initializer
- Handle overflows in address resources on 32-bit systems
- Extend extracting compatible strings in sources from function
parameters
- Use of_property_present() in DT unittest
- Clean-up of_irq_to_resource() to use helpers
- Support #msi-cells=<0> in of_msi_get_domain()
- Improve the kerneldoc for of_property_match_string()
- kselftest: Ignore nodes that have ancestors disabled"
* tag 'devicetree-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (59 commits)
dt-bindings: watchdog: Add rockchip,rk3576-wdt compatible
dt-bindings: cpu: Drop duplicate nvidia,tegra186-ccplex-cluster.yaml
dt-bindings: clock: mediatek: Drop duplicate mediatek,mt6795-sys-clock.yaml
of/irq: Use helper to define resources
of/irq: Make use of irq_get_trigger_type()
dt-bindings: clk: vc5: Make SD/OE pin configuration properties not required
drivers/of: Improve documentation for match_string
of: property: Do some clean up with use of __free()
dt-bindings: watchdog: qcom-wdt: document support on SA8255p
dt-bindings: interrupt-controller: fsl,irqsteer: Document fsl,imx8qm-irqsteer
dt-bindings: interrupt-controller: arm,gic: add ESPI and EPPI specifiers
dt-bindings: dma: Add lpc32xx DMA mux binding
dt-bindings: trivial-devices: Drop duplicate "maxim,max1237"
dt-bindings: trivial-devices: Drop duplicate LM75 compatible devices
dt-bindings: trivial-devices: Deprecate "ad,ad7414"
dt-bindings: trivial-devices: Drop incorrect and duplicate at24 compatibles
dt-bindings: wakeup-source: update reference to m8921-keypad.yaml
dt-bindings: interrupt-controller: qcom-pdc: document support for SA8255p
dt-bindings: Fix various typos
of: address: Unify resource bounds overflow checking
...
Pull devicetree updates from Rob Herring:
"DT Bindings:
- Convert and add a bunch of IBM FSI related bindings
- Add a new schema listing legacy compatibles which will (probably)
never be documented. This will silence various checks warning about
them.
- Add bindings for Sierra Wireless mangOH Green SPI IoT interface,
new Arm 2024 Cortex and Neoverse CPUs, QCom sc8180x PDC, QCom SDX75
GPI DMA, imx8mp/imx8qxp fsl,irqsteer, and Renesas RZ/G2UL CRU and
CSI-2 blocks
- Convert Spreadtrum sprd-timer, FSL cpm_qe, FSL fsl,ls-scfg-msi, FSL
q(b)man-*, FSL qoriq-mc, and img,pdc-wdt bindings to DT schema
- Drop obsolete stericsson,abx500.txt
DT core:
- Update dtc to upstream version v1.7.0-93-g1df7b047fe43
- Add support to run DT validation on DTs with applied overlays
- Add helper for creating boolean properties in dynamic nodes and use
that for dynamic PCI nodes
- Clean-up early parsing of '#{address,size}-cells'"
* tag 'devicetree-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (39 commits)
dt-bindings: timer: sprd-timer: convert to YAML
dt-bindings: incomplete-devices: document devices without bindings
dt-bindings: trivial-devices: document the Sierra Wireless mangOH Green SPI IoT interface
scripts/dtc: Update to upstream version v1.7.0-93-g1df7b047fe43
dt-bindings: soc: fsl: Add fsl,ls1028a-reset for reset syscon node
dt-bindings: soc: fsl: cpm_qe: convert to yaml format
dt-bindings: i2c: i2c-fsi: Convert to json-schema
dt-bindings: fsi: Document the FSI Hub Controller
dt-bindings: fsi: Document the AST2700 FSI controller
dt-bindings: fsi: ast2600-fsi-master: Convert to json-schema
dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller
dt-bindings: fsi: Document the FSI controller common properties
dt-bindings: fsi: Document the IBM SBEFIFO engine
dt-bindings: fsi: p9-occ: Convert to json-schema
dt-bindings: fsi: Document the IBM SCOM engine
dt-bindings: fsi: fsi2spi: Document SPI controller child nodes
dt-bindings: interrupt-controller: convert fsl,ls-scfg-msi to yaml
dt-bindings: soc: fsl: Convert q(b)man-* to yaml format
dt-bindings: misc: fsl,qoriq-mc: convert to yaml format
dt-bindings: drop stale Anson Huang from maintainers
...
It is possible to have thermal zones which don't have any trip points.
These zones in effect simply represent a temperature sensor without any
action associated with it. While the schema has always required a
'trips' node, users have existed for a long time without it. Update the
schema to match reality.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240709150154.3272825-1-robh@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The temperature output register of the Loongson-2K2000 is defined in the
chip configuration domain, which is different from the Loongson-2K1000,
so it can't be fallbacked.
We need to use two groups of registers to describe it: the first group
is the high and low temperature threshold setting register; the second
group is the temperature output register.
It is true that this fix will cause ABI corruption, but it is necessary
otherwise the Loongson-2K2000 temperature sensor will not work properly.
Fixes: 72684d99a8 ("thermal: dt-bindings: add loongson-2 thermal")
Cc: Yinbo Zhu <zhuyinbo@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/5198999d679f1a1c3457385acb9fadfc85da1f1e.1713837379.git.zhoubinbin@loongson.cn
Pull more thermal control updates from Rafael Wysocki:
"These update thermal drivers for ARM platforms by adding new hardware
support (r8a779h0, H616 THS), addressing issues (Mediatek LVTS,
Mediatek MT7896, thermal-of) and cleaning up code.
Specifics:
- Fix memory leak in the error path at probe time in the Mediatek
LVTS driver (Christophe Jaillet)
- Fix control buffer enablement regression on Meditek MT7896 (Frank
Wunderlich)
- Drop spaces before TABs in different places: thermal-of, ST drivers
and Makefile (Geert Uytterhoeven)
- Adjust DT binding for NXP as fsl,tmu-range min/maxItems can vary
among several SoC versions (Fabio Estevam)
- Add support for the H616 THS controller on Sun8i platforms (Martin
Botka)
- Don't fail probe due to zone registration failure because there is
no trip points defined in the DT (Mark Brown)
- Support variable TMU array size for new platforms (Peng Fan)
- Adjust the DT binding for thermal-of and make the polling time not
required and assume it is zero when not found in the DT (Konrad
Dybcio)
- Add r8a779h0 support in both the DT and the rcar_gen3 driver (Geert
Uytterhoeven)"
* tag 'thermal-6.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/drivers/rcar_gen3: Add support for R-Car V4M
dt-bindings: thermal: rcar-gen3-thermal: Add r8a779h0 support
thermal/of: Assume polling-delay(-passive) 0 when absent
dt-bindings: thermal-zones: Don't require polling-delay(-passive)
thermal/drivers/qoriq: Fix getting tmu range
thermal/drivers/sun8i: Don't fail probe due to zone registration failure
thermal/drivers/sun8i: Add support for H616 THS controller
thermal/drivers/sun8i: Add SRAM register access code
thermal/drivers/sun8i: Extend H6 calibration to support 4 sensors
thermal/drivers/sun8i: Explain unknown H6 register value
dt-bindings: thermal: sun8i: Add H616 THS controller
soc: sunxi: sram: export register 0 for THS on H616
dt-bindings: thermal: qoriq-thermal: Adjust fsl,tmu-range min/maxItems
thermal: Drop spaces before TABs
thermal/drivers/mediatek: Fix control buffer enablement on MT7896
thermal/drivers/mediatek/lvts_thermal: Fix a memory leak in an error handling path
