[Why]
Due to very small clock register delta between DCN35 and DCN351, clock
spread is being checked on the wrong register for DCN351, causing the
display driver to believe that DPREFCLK downspread to be disabled when
in some stacks it is enabled. This causes the clock values for audio to
be incorrect.
[How]
Both DCN351 and DCN35 use the same clk_mgr, so we modify the DCN35
function that checks for SSC enable to read CLK6 instead of CLK5 when
using DCN351. This allows us to read for DPREFCLK downspread correctly
so the clock can properly compensate when setting values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Kevin Gao <kevin.gao3@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
dp_is_128b_132b_signal dereferences pipe->stream so it is necessary to
check it in advance.
Also fix erroneous spaces and move a variable declaration to top.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should never apply a minimum dispclk value while in prepare_bandwidth
or while displays are active. This is always an optimization for when
all displays are disabled.
[How]
Defer dispclk optimization until safe_to_lower = true and display_count
reaches 0.
Since 0 has a special value in this logic (ie. no dispclk required)
we also need adjust the logic that clamps it for the actual request
to PMFW.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting min dispclk to 50Mhz outside clock lowering function causes
unnecessary calls to SMU to lower dispclk and causes dentist hangs when
there is no stream on the pipes.
[How]
Move the set minimum dispclk logic inside the lowering dispclk if
statement.
Fixes: 2344413205 ("DCN35 set min dispclk to 50Mhz")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
immediate_disable_crtc does not reset ODM. if switching to disable_crtc
which will disable ODM as well. i.e. need to restore ODM mem cfg at
reenable it at end of w/a.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is a workaround for an dcn3.1 hang that happens if otg dispclk
is ramped while otg is on and stream enc is off.
But this w/a should not trigger when we have a dig active.
[How]
Avoid disable otg when dig FE/BE FIFO was not switched.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Jingwen Zhu <jingwen.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In OTG disable workarund, CRTC is disabled immediately
to improve performance, but this may cause timing issue
in DP HPO encoder FIFO and result in blank CRCs.
[How]
Replace the immediate CRTC disable call with normal disable call
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Xi (Alex) Liu <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The null checks for ctx->dc_bios are redundant as it was already
dereferenced previously, as reported by Coverity; therefore the
null checks are removed.
This fixes 7 REVERSE_INULL issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Tell the system about the current host router bandwidth to be used to
measure and calculate the right voltage to be used.
[how]
Send SMU message of each DPIA host router bandwidth.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous patch to allow DTBCLK disable didn't address boot case. Driver
thinks DTBCLK is disabled by default, so we don't send disable message to
PMFW. DTBCLK is then enabled at idle desktop on boot, burning power.
[How]
Set dtbclk_en to true on boot so that disable message is sent during first
commit.
Fixes: 27750e176a ("drm/amd/display: Allow DTBCLK disable for DCN35")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On 14us for exit latency time causes underflow for 8K monitor with HDR on.
Increasing the latency to 28us fixes the underflow.
[How]
Increase the latency to 28us. This workaround should be sufficient
before we figure out why SR exit so long.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous patch to allow DTBCLK disable didn't address boot case. Driver
thinks DTBCLK is disabled by default, so we don't send disable message to
PMFW. DTBCLK is then enabled at idle desktop on boot, burning power.
[How]
Set dtbclk_en to true on boot so that disable message is sent during first
commit.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.
For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.
We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching to another HDMI mode, we are unnecesarilly
disabling/enabling FIFO causing both HPO and DIG registers to be set at
the same time when only HPO is supposed to be set.
This can lead to a system hang the next time we change refresh rates as
there are cases when we don't disable OTG/FIFO but FIFO is enabled when
it isn't supposed to be.
[How]
Removing the enable/disable FIFO entirely.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
w/a use case:
- dual display, compliance, toggling between the displays
- switching between 120Hz 420 -> 144Hz 444 and vice versa
- switching between 144Hz -> 60Hz TMDS or vice versa
It'd typically involve TMDS in some capacity since that's the only link
signal we leave the OTG running but DIO/PHY off you can hit this in
cases where you have multiple displays as well it syncs with the first
active OTG, so if you had OTG[0] mapped and FIFO off you'd hit it even
if OTG[1] was mapped and had FIFO
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DTBCLK is enabled on idle and it will burn power.
[How]
There's a few issues here:
- Always enabling DTBCLK on clock manager init
- Setting refclk when DTBCLK is supposed to be disabled
- Not applying the correct calculated version refclk, but instead the
base value which might be zero
On dtbclk_en change we'll message PMFW to enable or disable the clock
accordingly.
The DTBDTO will be then based on refclk, but it will be set to the
default fixed value if there was nothing calculated in DML despite the
clock being considered enabled.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.
The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.
[How]
Build the table based on DcfClock with the following assumptions:
1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.
2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.
3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
