This is a preparation patch for the introduction of CAN XL.
CAN FD and CAN XL uses similar bittiming parameters. Add one level of
nesting for all the CAN FD parameters. Typically:
priv->can.data_bittiming;
becomes:
priv->can.fd.data_bittiming;
This way, the CAN XL equivalent (to be introduced later) would be:
priv->can.xl.data_bittiming;
Add the new struct data_bittiming_params which contains all the data
bittiming parameters, including the TDC and the callback functions.
This done, update all the CAN FD drivers to make use of the new
layout.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250501171213.2161572-2-mailhol.vincent@wanadoo.fr
[mkl: fix rcar_canfd]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
dev_err_probe() is used to log an error message during the probe process
of a device.
It can simplify the error path and unify a message template.
Using this helper is totally fine even if err is known to never
be -EPROBE_DEFER.
The benefit compared to a normal dev_err() is the standardized format
of the error code, it being emitted symbolically and the fact that
the error code is returned which allows more compact error paths.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Link: https://patch.msgid.link/20240830110651.519119-1-yanzhen@vivo.com
mkl: fix indention
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add hardware timestamp support for all usbcan based devices (M16C).
The usbcan firmware is slightly different compared to the other Kvaser USB
interfaces:
- The timestamp is provided by a 32-bit counter, with 10us resolution.
Hence, the hardware timestamp will wrap after less than 12 hours.
- Each Rx CAN or Tx ACK command only contains the 16-bits LSB of the
timestamp counter.
- The 16-bits MSB are sent in an asynchronous event (command), if any
change occurred in the MSB since the last event.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20240701154936.92633-13-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Debian's gcc-13 [1] throws the following error in
kvaser_usb_hydra_cmd_size():
[1] gcc version 13.0.0 20221214 (experimental) [master r13-4693-g512098a3316] (Debian 13-20221214-1)
| drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c:502:65: error:
| array subscript ‘struct kvaser_cmd_ext[0]’ is partly outside array
| bounds of ‘unsigned char[32]’ [-Werror=array-bounds=]
| 502 | ret = le16_to_cpu(((struct kvaser_cmd_ext *)cmd)->len);
kvaser_usb_hydra_cmd_size() returns the size of given command. It
depends on the command number (cmd->header.cmd_no). For extended
commands (cmd->header.cmd_no == CMD_EXTENDED) the above shown code is
executed.
Help gcc to recognize that this code path is not taken in all cases,
by calling kvaser_usb_hydra_cmd_size() directly after assigning the
command number.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/all/20221219110104.1073881-1-mkl@pengutronix.de
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c
2871edb32f ("can: kvaser_usb: Fix possible completions during init_completion")
abb8670938 ("can: kvaser_usb_leaf: Ignore stale bus-off after start")
8d21f5927a ("can: kvaser_usb_leaf: Fix improved state not being reported")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device will respond with a CMD_ERROR_EVENT command, with error_code
KVASER_USB_{LEAF,HYDRA}_ERROR_EVENT_PARAM, if the CMD_SET_BUSPARAMS_REQ
contains invalid bittiming parameters.
However, this command does not contain any channel reference.
To check if the CMD_SET_BUSPARAMS_REQ was successful, redback and compare
the requested bittiming parameters with the device reported parameters.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-12-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When auto-restart is enabled, the kvaser_usb_leaf driver considers
transition from any state >= CAN_STATE_BUS_OFF as a bus-off recovery
event (restart).
However, these events may occur at interface startup time before
kvaser_usb_open() has set the state to CAN_STATE_ERROR_ACTIVE, causing
restarts counter to increase and CAN_ERR_RESTARTED to be sent despite no
actual restart having occurred.
Fix that by making the auto-restart condition checks more strict so that
they only trigger when the interface was actually in the BUS_OFF state.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 it was observed
that if the device was bus-off when stopped, at next start (either via
interface down/up or manual bus-off restart) the initial
CMD_CHIP_STATE_EVENT received just after CMD_START_CHIP_REPLY will have
the M16C_STATE_BUS_OFF bit still set, causing the interface to
immediately go bus-off again.
The bit seems to internally clear quickly afterwards but we do not get
another CMD_CHIP_STATE_EVENT.
Fix the issue by ignoring any initial bus-off state until we see at
least one bus-on state. Also, poll the state periodically until that
occurs.
It is possible we lose one actual immediately occurring bus-off event
here in which case the HW will auto-recover and we see the recovery
event. We will then catch the next bus-off event, if any.
This issue did not reproduce with 0bfd:0017 Kvaser Memorator
Professional HS/HS FW 2.0.50.
Fixes: 71873a9b38 ("can: kvaser_usb: Add support for more Kvaser Leaf v2 devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 sends a
CMD_CHIP_STATE_EVENT indicating bus-off after stopping the device,
causing a stopped device to appear as CAN_STATE_BUS_OFF instead of
CAN_STATE_STOPPED.
Fix that by not handling error events on stopped devices.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tested 0bfd:0017 Kvaser Memorator Professional HS/HS FW 2.0.50 and
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 do not seem to send
any unsolicited events when error counters decrease or when the device
transitions from ERROR_PASSIVE to ERROR_ACTIVE (or WARNING).
This causes the interface to e.g. indefinitely stay in the ERROR_PASSIVE
state.
Fix that by asking for chip state (inc. counters) event every 0.5 secs
when error counters are non-zero.
Since there are non-error-counter devices, also always poll in
ERROR_PASSIVE even if the counters show zero.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
kvaser_usb_leaf_rx_error_update_can_state() sets error state according
to error counters when the hardware does not indicate a specific state
directly.
However, this is currently gated behind a check for
M16C_STATE_BUS_ERROR which does not always seem to be set when error
counters are increasing, and may not be set when error counters are
decreasing.
This causes the CAN_STATE_ERROR_WARNING state to not be set in some
cases even when appropriate.
Change the code to set error state from counters even without
M16C_STATE_BUS_ERROR.
The Error-Passive case seems superfluous as it is already set via
M16C_STATE_BUS_PASSIVE flag above, but it is kept for now.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The TX queue seems to be implicitly flushed by the hardware during
bus-off or bus-off recovery, but the driver does not reset the TX
bookkeeping.
Despite not resetting TX bookkeeping the driver still re-enables TX
queue unconditionally, leading to "cannot find free context" /
NETDEV_TX_BUSY errors if the TX queue was full at bus-off time.
Fix that by resetting TX bookkeeping on CAN restart.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
flush_comp is initialized when CMD_FLUSH_QUEUE is sent to the device and
completed when the device sends CMD_FLUSH_QUEUE_RESP.
This causes completion of uninitialized completion if the device sends
CMD_FLUSH_QUEUE_RESP before CMD_FLUSH_QUEUE is ever sent (e.g. as a
response to a flush by a previously bound driver, or a misbehaving
device).
Fix that by initializing flush_comp in kvaser_usb_init_one() like the
other completions.
This issue is only triggerable after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
