The driver needs to handle GPIO interrupts to identify SFP module and
configure PHY by sending mailbox messages to firmware.
Since the SFP module needs to wait for ready to get information when it
is inserted, workqueue is added to handle delayed tasks. And each SW-FW
interaction takes time to wait, so they are processed in the workqueue
instead of IRQ handler function.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/399624AF221E8E28+20250521064402.22348-6-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For the following patches to support PHYLINK for AML 25G devices,
separate MAC type wx_mac_aml40 to maintain the driver of 40G devices.
Because 40G devices will complete support later, not now.
And this patch makes the 25G devices use some PHYLINK interfaces, but it
is not yet create PHYLINK and cannot be used on its own. It is just
preparation for the next patches.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/592B1A6920867D0C+20250521064402.22348-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Most of the different code that requires MAC type in the common library
is due to NGBE only supports a few queues and pools, unlike TXGBE, which
supports 128 queues and 64 pools. This difference accounts for most of
the hardware configuration differences in the driver code. So add a flag
bit "WX_FLAG_MULTI_64_FUNC" for them to clean-up the driver code.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/C731132E124D75E5+20250521064402.22348-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When txgbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in txgbe_probe() function, the subsequent
error paths after txgbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when txgbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Fixes: 937d46ecc5 ("net: wangxun: add ethtool_ops for channel number")
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250415032910.13139-1-abdun.nihaal@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a new 40/25/10 Gigabit Ethernet device.
To support basic functions, PHYLINK is temporarily skipped as it is
intended to implement these configurations in the firmware. And the
associated link IRQ is also skipped.
And Implement the new SW-FW interaction interface, which use 64 Byte
message buffer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250221065718.197544-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using MSI/INTx interrupt, the shared interrupts are still being
handled in the device remove routine, before free IRQs. So isb memory
is still read after it is freed. Thus move wx_free_isb_resources()
from txgbe_close() to txgbe_remove(). And fix the improper isb free
action in txgbe_open() error handling path.
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When using MSI or INTx interrupts, request_irq() for pdev->irq will
conflict with request_threaded_irq() for txgbe->misc.irq, to cause
system crash. So remove txgbe_request_irq() for MSI/INTx case, and
rename txgbe_request_msix_irqs() since it only request for queue irqs.
Add wx->misc_irq_domain to determine whether the driver creates an IRQ
domain and threaded request the IRQs.
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Support the addition and deletion of Flow Director filters.
Supported fields: src-ip, dst-ip, src-port, dst-port
Supported flow-types: tcp4, udp4, sctp4, ipv4
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add flow director ATR filter. ATR mode is enabled by default to filter
TCP packets.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When VLAN tag strip is changed to enable or disable, the hardware requires
the Rx ring to be in a disabled state, otherwise the feature cannot be
changed.
Fixes: f3b03c655f ("net: wangxun: Implement vlan add and kill functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware requires VLAN CTAG and STAG configuration always matches. And
whether VLAN CTAG or STAG changes, the configuration needs to be changed
as well.
Fixes: 6670f1ece2 ("net: txgbe: Add netdev features support")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register of GPIO interrupt status is masked before MAC IRQ
is enabled. This is because of hardware deficiency. So manually
clear the interrupt status before using them. Otherwise, GPIO
interrupts will never be reported again. There is a workaround for
clearing interrupts to set GPIO EOI in txgbe_up_complete().
Fixes: aefd013624 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get RX/TX queue number with ethtool -l, and set RX/TX
queue number with ethtool -L. Since interrupts need to be rescheduled,
adjust the allocation of msix enties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support to query RX/TX depth with ethtool -g, and change RX/TX depth
with ethtool -G.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device uses a custom subsystem vendor ID, the function
wx_sw_init() returns before the memory of 'wx->mac_table' is allocated.
The null pointer will causes the kernel panic.
Fixes: 79625f45ca ("net: wangxun: Move MAC address handling to libwx")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wangxun SP chip supports to connect with external PHY (marvell 88x3310),
which links to 10GBASE-T/1000BASE-T/100BASE-T. Add the identification of
media types from subsystem device IDs. For sp_media_copper, register mdio
bus for the external PHY.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since XPCS device identifier is implemented in the firmware version
0x20010 and above, so add a warning to prompt the users to upgrade the
firmware to make sure the driver works.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txgbe_shutdown() relies on txgbe_dev_shutdown() to initialise
wake by passing it by reference. However, txgbe_dev_shutdown()
doesn't use this parameter at all.
wake is then passed uninitialised by txgbe_dev_shutdown()
to pci_wake_from_d3().
Resolve this problem by:
* Removing the unused parameter from txgbe_dev_shutdown()
* Removing the uninitialised variable wake from txgbe_dev_shutdown()
* Passing false to pci_wake_from_d3() - this assumes that
although uninitialised wake was in practice false (0).
I'm not sure that this counts as a bug, as I'm not sure that
it manifests in any unwanted behaviour. But in any case, the issue
was introduced by:
3ce7547e5b ("net: txgbe: Add build support for txgbe")
Flagged by Smatch as:
.../txgbe_main.c:486 txgbe_shutdown() error: uninitialized symbol 'wake'.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Cc: Mengyuan Lou <mengyuanlou@net-swift.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the basic ethtool ops get_drvinfo and get_link for ngbe and txgbe.
Ngbe implements get_link_ksettings, nway_reset and set_link_ksettings
for free using phylib code.
The code related to the physical interface is not yet fully implemented
in txgbe using phylink code. So do not implement get_link_ksettings,
nway_reset and set_link_ksettings in txgbe.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230214091527.69943-1-mengyuanlou@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean Rx and Tx ring interrupts, process packets in the data path.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the configuration of Rx and Tx ring, set Rx flags and implement
ndo_set_rx_mode ops.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine proper interrupt scheme to enable and handle interrupt.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to move the total members in struct adapter to struct wx_hw
to keep the code clean, it's a bad name of 'wx_hw' only for hardware.
Rename 'wx_hw' to 'wx', and rename the pointers at use.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
