On dm816x the clocks are sourced from a FAPLL (Flying Adder PLL)
that does not seem to be used on the other omap variants.
There are four instances of the FAPLL on dm816x that each have three
to seven child synthesizers.
I've set up the FAPLL as a single fapll.c driver. Later on we could
potentially have the PLL code generic. To do that, we would have to
consider the following:
1. Setting the PLL to bypass mode also sets the child synthesizers
into bypass mode. As the bypass rate can also be generated by
the PLL in regular mode, there's no way for the child synthesizers
to detect the bypass mode based on the parent clock rate.
2. The PLL registers control the power for each of the child
syntheriser.
Note that the clocks are currently still missing the set_rate
implementation so things are still running based on the bootloader
values. That's OK for now as most of the outputs have dividers and
those can be set using the existing TI component clock code.
I have verified that the extclk rates are correct for a few clocks,
so adding the set_rate support should be fairly trivial later on.
This code is partially based on the TI81XX-LINUX-PSP-04.04.00.02
patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
On the A80 SoC, the 4 mmc controllers each have a separate register
controlling their register access clocks and reset controls. These
registers in turn share a ahb clock gate and reset control.
This patch adds a platform device driver for these controls. It
requires both clocks and reset controls to be available, so using
CLK_OF_DECLARE might not be the best way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The module 0 style clocks, or storage module clocks as named in the
official SDK, are almost the same as the module 0 clocks on earlier
Allwinner SoCs. The only difference is wider mux register bits.
As with earlier Allwinner SoCs, mmc module clocks are a special case
of mod0 clocks, with phase controls for 2 child clocks, output and
sample.
This patch adds support for both.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Instead of having three different clocks for the main MMC clock and the two
phase sub-clocks, which involved having three different drivers sharing the
same register, rework it to have the same single driver registering three
different clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Add the ADSP clock support to the R-Car generation 2 CPG driver. This clock
gets derived from PLL1. The layout of the ADSPCKCR register is similar to
those of the clocks supported by the 'clk-div6' driver but the divider encoding
is non-linear, so can't be supported by that driver...
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the RCAN clock support to the R-Car generation 2 CPG driver. This clock
gets derived from the USB_EXTAL clock, dividing it by 6. The layout of the
RCANCKCR register is similar to those of the clocks supported by the 'clk-div6'
driver but has no divider field, and so can't be supported by that driver...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch unifies the sun6i AHB1 clock, originally supported
with separate mux and divider clks. It also adds support for
the pre-divider on the PLL6 input, thus allowing the clock to
be muxed to PLL6 with proper clock rate calculation.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
Allwinner Clocks additions for 3.19
A few patches that should go through the clock tree, mostly fixes, cleanups,
and new clocks additions to start to support the A80.
Some clock modules on the A31 use PLL6x2 as one of their inputs.
This patch changes the PLL6 implementation for A31 to a divs clock,
i.e. clock with multiple outputs that have different dividers.
The first output will be the normal PLL6 output, and the second
will be PLL6x2.
This patch fixes the PLL6 N factor in the clock driver, and removes
any /2 dividers in the PLL6 factors clock part. The N factor counts
from 1 to 32, mapping to values 0 to 31, as shown in the A31 manual.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This driver does not match the hardware, which is actually compatible
to sun4i-a10-apb1-clk. Since we've switch to the correct one, drop
this driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock controller module (CCM) has several clock inputs, which
are connected to external crystal oscillators. To reflect this,
assign these fixed clocks to the CCM node directly.
This especially resolves initialization order dependencies we had
with the earlier initialization code: When resolving of the fixed
clocks failed in clk-vf610, the code created fixed clocks with a
rate of 0.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This commit unifies the APB1 mux with the APB1 clock, using the new
factors infrastructure.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Add mux mask bits]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has 12 PLL clocks, 3 AHB clocks, 2 APB clocks, and a
new "GT" bus, which I assume is some kind of data bus connecting
the processor cores, memory and various busses. Also there is a
bus clock for a ARM CCI400 module.
As far as I can tell, the GT bus and CCI400 bus clock must be
protected.
This patch adds driver support for peripheral related PLLs and
bus clocks on the A80. The GT and CCI400 clocks are added as well
as these 2 along with the PLLs they are clocked from must not be
disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull clock tree updates from Mike Turquette:
"The clk tree changes for 3.18 are dominated by clock drivers. Mostly
fixes and enhancements to existing drivers as well as new drivers.
This tag contains a bit more arch code than I usually take due to some
OMAP2+ changes. Additionally it contains the restart notifier
handlers which are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree
I had to revert one patch and follow up with one more fix near the tip
of this tag. Some dead code is introduced but it will soon become
live code after 3.18-rc1 is released as the rest of the PXA family is
converted over to the common clock framework.
Another trend in this tag is that multiple vendors have started to
push the complexity of changing their CPU frequency into the clock
driver, whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to
some confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems."
* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
clk: pxa clocks build system fix
Revert "arm: pxa: Transition pxa27x to clk framework"
clk: samsung: register restart handlers for s3c2412 and s3c2443
clk: rockchip: add restart handler
clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
doc/kernel-parameters.txt: clarify clk_ignore_unused
arm: pxa: Transition pxa27x to clk framework
dts: add devicetree bindings for pxa27x clocks
clk: add pxa27x clock drivers
arm: pxa: add clock pll selection bits
clk: dts: document pxa clock binding
clk: add pxa clocks infrastructure
clk: gpio-gate: Ensure gpiod_ APIs are prototyped
clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
clk: ti: LLVMLinux: Move __init outside of type definition
clk: ti: consider the fact that of_clk_get() might return an error
clk: ti: dra7-atl-clock: fix a memory leak
clk: ti: change clock init to use generic of_clk_init
clk: hix5hd2: add I2C clocks
clk: hix5hd2: add watchdog0 clocks
...
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support. Among the things new for this release
are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier
SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still
ongoing"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits)
ARM: hisi: depend on ARCH_MULTI_V7
CNS3xxx: Fix debug UART.
ARM: at91: fix nommu build regression
ARM: meson: add basic support for MesonX SoCs
ARM: meson: debug: add debug UART for earlyprintk support
irq: Export handle_fasteoi_irq
ARM: mediatek: Add earlyprintk support for mt6589
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
ARM: debug: fix alphanumerical order on debug uarts
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
...
Document the device-tree binding of Marvell PXA based SoCs.
PXA clocks are mostly fixed rate and fixed ratio clocks derived from an
external oscillator, and gated by a register set (CKEN or CKEN*).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Allwinner Clocks Additions for 3.18
The most important part of this serie is the addition of the phase API to
handle the MMC clocks in the Allwinner SoCs.
Apart from that, the A23 gained a new mbus driver, and there's a fix for a
incorrect divider table on the APB0 clock.
The MBUS clock on sun8i is slightly different from the old mod0 clocks.
The divider is 3 bits wider, while also needing a divider table for the
higher 4 values, which all set the same divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
